RoboVac Owner’s Manual T2150/T2151 51005001723 V01
Table of Contents 02 Important Safety Instructions 15 About Your RoboVac What's in the Box RoboVac Anatomy LED Indication 19 Using Your RoboVac Important Tips Before Use Preparation Charge Your RoboVac Use Your RoboVac with the EufyHome App Start / Stop Cleaning Select a Cleaning Mode Select a Suction Power Level Use Mopping System Use Your RoboVac with Amazon Alexa / the Google Assistant 31 Cleaning and Maintenance Clean the Dust Collector and Filter Clean the Side Brushes Replace the Side Brushes C
Important Safety Instructions To reduce the risk of injury or damage, read these safety instructions carefully and keep them at hand when setting up, using, and maintaining this device. WARNING SYMBOLS USED This is the safety alert symbol. This symbol alerts you to potential hazards that could result in property damage and/or serious bodily harm or death.
• Do not operate this device in areas with exposed electrical outlets on the floor. • Do not expose the electronics of this device, its battery, or the integrated Charging Base. There are no userserviceable parts inside. • Do not use this device on an unfinished, unsealed, waxed or rough floor. It may result in damage to the floor and this device. Use only on hard floor surfaces or low-pile carpet. • This device has been designed to be used on floors without scratching them.
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver.
Consignes importantes de sécurité Pour réduire le risque de blessure ou de dommage, lisez attentivement les consignes de sécurité et gardez-les à portée de main lors de la configuration, l'utilisation et l'entretien de cet appareil. SYMBOLES D'AVERTISSEMENT UTILISÉS Il s'agit du symbole d'avertissement de sécurité. Ce symbole vous alerte sur les dangers potentiels qui peuvent entraîner des dommages matériels et/ou des lésions corporelles graves ou la mort..
d'un cordon d'alimentation et le traîne avec lui, un objet peut tomber d'une table ou d'une étagère. • Si la pièce à nettoyer possède un balcon, une barrière physique doit être utilisée pour empêcher l'accès au balcon et garantir un fonctionnement sécurisé. • Ne rien placer sur le dessus de cet appareil. • Gardez à l'esprit que cet appareil se déplace par ses propres moyens. Faites attention en marchant dans la zone où cet appareil fonctionne, afin d'éviter de marcher dessus.
Déclaration FCC Cet appareil est conforme au Chapitre 15 du règlement FCC. Le fonctionnement est soumis aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si celui-ci est susceptible d'en compromettre le fonctionnement.
Avis de marque déposée • Amazon, Echo, Alexa et tous les logos associés sont des marques commerciales d'Amazon.com, Inc. ou de ses filiales. • Apple et le logo Apple sont des marques déposées d'Apple Inc., enregistrées aux États-Unis et dans d'autres pays. App Store est une marque de service d'Apple Inc., enregistrée aux États-Unis et dans d'autres pays. • Google Play et le logo Google Play sont des marques de Google Inc. • Google Home est une marque de Google Inc.
C. Dust Collector RoboVac Anatomy A. Top & Side Filter Auto cleaning control button Wi-Fi status light Bumper D. Suction Inlet Infrared sensor Dust collector Dust collector Dust collector release button B. Bottom Drop sensor Charging contact pins Charging contact pins Swivel wheel Side brushes Drop sensor E.
F. Water Tank (Wi-Fi Status Light) Washable mopping cloth Status Slowly flashing blue Waiting for connection Rapidly flashing blue Connecting with your wireless router Solid blue Connected to your wireless router Slot Fliter element Fliter element Using Your RoboVac Important Tips Before Use Cloth attachment area Snap joints Snap joints Water inlet Water inlet cover a b c d e f Movable pulley LED Indication You can see the status of RoboVac from the LED indicators.
Anti-drop sensors will prevent RoboVac from tumbling down stairs and steep drops in most cases. Sensors are less effective if dirty or used on carpeted/reflective/very dark-colored floors. It is recommended to place physical barriers to block off areas where RoboVac may fall. 4 Turn on the main power switch on the bottom of RoboVac. Place physical barriers in front of fireplaces and areas that may cause damage to RoboVac if entered.
7 Connect the round connector of the adapter into the power socket on the Charging Base and the other end into a wall outlet. When the Charging Base connects to AC power, the LED indicator on the Charging Base is SOLID WHITE. • Turn off the main power switch if RoboVac will not be used for a long period of time. To preserve the battery’s lifespan, recharge at least once every 6 months.
Wi-Fi Status Light Slowly flashing blue Waiting for connection Rapidly flashing blue Connecting with your wireless router Solid blue Connected with your wireless router 1 Press on RoboVac to start cleaning in Auto Mode. 2 Press again to pause cleaning. • If you have any problems during the Wi-Fi setup process, refer to the “Troubleshooting > Wi-Fi connection” section in this Manual. • If RoboVac gets stuck in any space, tap Find My Robot in the app to find the machine.
Press on RoboVac to start cleaning in Auto Mode. Select a Suction Power Level In the EufyHome app, select a suction power level according to your needs: • Standard (Default) • Max When RoboVac starts cleaning the next time, it will clean according to the suction power level you previously selected. Use Mopping System • The mopping mode is not recommended when no one is at home. • Only use the mopping mode on a floor without carpets.
3 Open the water inlet cover to fill the water, then close the cover. 6 When RoboVac finishes working and returns to the Charging Base, press the release button to remove the dust collector and the water tank. Do not use floor cleaner or detergent which may block the filter elements. 4 Install the water tank into the bottom of RoboVac until a click is heard. The mopping mode is only intended for a clean floor without stubborn stains.
Use Your RoboVac with Amazon Alexa / the Google Assistant Amazon Alexa or the Google Assistant is a smart voice control device that enables you to control RoboVac with your voice. Currently this feature only supports English, German, French, and Spanish. You could check regularly if more languages are supported at https://www.eufylife.com/ support/. Cleaning and Maintenance For optimal performance, follow the instructions below to clean and maintain RoboVac regularly.
2 Open and empty the dust collector. 5 Place the filter back into the dust collector. 6 Push the dust collector back into the main unit. 3 Remove the filter. Clean the Side Brushes 4 Tap the filter to remove dust. Foreign substances, such as hair, can easily get tangled in the side brushes, and dirt may adhere to them. Be sure to clean them regularly. 1 Remove the side brushes.
2 Carefully unwind and pull off any hair or string that is wrapped between the main unit and the side brushes. 3 Use a cloth dampened with warm water to remove dust from the brushes or to gently reshape them. Clean the Sensors and Charging Pins To maintain the best performance, clean the drop sensors and charging pins regularly. • Dust off the drop sensors and charging contact pins using a cloth or cleaning brush. Only use the side brushes when they are completely dry.
2 Clean any hair or debris wrapped around the wheel or entangled inside the wheel 2 Remove the cover plate and then take out the rubber strip. cavity. 3 Reinstall the wheel and push in until it clicks into place. 1 Do not clean the swivel wheel with water. 2 Clean the Mopping Cloth and Water Tank It is recommended to clean the mopping cloth and water tank after each use. 3 Install the new rubber strip in place. 24h 2 1 1 After each use, remove the mopping cloth from the water tank.
Troubleshooting Problems Solutions Problems RoboVac’s movements • Clean the sensors carefully with a dry cloth. or travel path are • Restart RoboVac by turning the power switch off and on. abnormal. • Make sure the main power switch is in the ON position. RoboVac cannot be activated. • Make sure the battery is fully charged. • If you still have trouble, turn off the main power switch and then turn it back on. • Check if RoboVac is trapped or stuck on an obstacle. RoboVac stops working suddenly.
Problems Solutions Voice Prompt • Check if there are any Internet connection problems. You cannot control RoboVac with the Google Assistant. • Check if you have installed the Google Home app onto your smart device and initiated the “EufyHome” action in the Google Home app. For details, refer to the “Smart Integrations” page in the EufyHome App.
- You are using a 2.4GHz router or a dual-band router that is configured to support a 2.4GHz frequency band. RoboVac does not support 5GHz frequency band. - If RoboVac cannot connect to the Wi-Fi network and you are using a 2.4/5GHz mixed network, switch to a 2.4GHz network for Wi-Fi setup. You can switch back once your setup is complete. - When connecting to a hidden network, make sure you enter the correct network name, SSID (case sensitive), and connecting to a 2.4GHz wireless network.
