湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 产品规格书 Product Specification Sheet 深圳海翼智新科技有限公司 CUSTOMER/客户： CUSTOMER P.N./客户料号： T8001 MODEL NO./产品型号： PA11 PRODUCT NO./产品编码： P0077-P1 REV1.1 REVERSION NO./版本： PREPARED DATE/拟制日期： 2018-07-03 CUSTOMER AUTHORIZED SIGNATURE/客户承认签核 PREPARED BY/拟 制: CHECKED BY/审 核: APPROVED BY/批 准: Please return to us one copy of “SPECIFICATION FOR APPROVAL” with you approved signature./客户确认签字，盖章后请回传一份承认书给我司.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD E. C. LIST/变更履历表 Rev. 版本 Description of Change/变更内容描述 Changed Remark Date/日期 /备注 Before/变更前 After/变更后 1.0 Original Release（初次发行） --- 2018.05.25 1.1 --- 更新外观图(更新贴纸) 2018.07.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD ** Table Of Content/目录 ** 1. Apply for Scope ……………………………………………………………………………………3 适用范围 2. Battery Specification …………………………………………… ………………………………3 电池规格 3. PCM Specification …………………………………………………………………………………7 保护板规格 4. Cell Specification ……………………………………………………… 电芯规格 5.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 1. Apply for Scope 适用范围 This specification describes the function of chargeable Li-ion polymer battery that made in GIANTSUN POWER CORPORATION. 本规格说明书描述了湖南炬神电子有限公司生产的可充电锂电池产品性能指标。 2. Battery Specification 电池规格： （本体高 66.8mm+出线长度 60.0±3mm）*37.5*19 3.7V/2600mAh 2pcs）。 7.4V/2600mAh （锂电芯:创明 18650 2.1 Shape Picture Content 电池外观图 2.1.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 2.2 Battery Specification Parameter: 电池参数规格 表一 No. Items Specifications 序号 项目 规格 1 2 3 4 5 6 7 8 Appearance 外观 Nominal Voltage 标称电压 Nominal Capacity 标称容量 Minimum Capacity 最小容量 Charge Voltage 充电电压 Discharge Cut-off Voltage 放电截止电压 Over-Charging Protection Voltage 过充保护电压 Over-Discharging Protection Voltage 过放保护电压 The surface is clear and no scratch, no mechanical abrasion, match well with the main machine 电池外表面清洁，无擦伤，无机械损伤，与主机配合良好 7.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD No. 序号 15 16 17 18 19 20 21 Items 项目 Impedance Specifications 规格 ≤200mΩ. The impedance shall be measured at AC 1000 Hz initially. 内阻 Cycle Life 循环寿命 Pack Dimension 电池尺寸 Storage 储存 Warranty Time 质量保证期 Battery Weight 电池重量 Delivery voltage 出货电压 Charge the battery at 0.5C under 15℃~35℃until the battery voltage reaches 4.20V, and then charge it under the constant voltage until the current ≤0.02C. Stay it for 0.5h-1h, and then discharge it at 0.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 2.3 Safety Performance 安全性能 表二 No. 序号 1 2 3 Items 项目 Over-Charge Protection 过充保护 Test Method and Condition 测试方法与条件 At 20±5℃ conditions, after fast-charging, use an external 10V power to load the battery and last for 8 hours, then check the appearance of battery. 在环境温度(20±5)℃下, 电池快 速充电结束后,用电压为 10V 外接电源 持续给电池载入 8 小时，再检查电池外 观。 At20±5℃conditions,discharge battery to 6.0V with 0.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 3. PCM Specification 保护板规格 3.1 Electrical Characteristics (at RT=25℃ ) 电气性能 (在环境温度：25℃) A). Protection Criteria 保护规格 a). Over-Charging Protection Voltage: 过充保护电压: 8.56±0.05V b). Over-Charging Protection Delay Time: 过充电保护延时： 0.7～1.3S c). Over-Discharging Protection Voltage: 过放保护电压: d). Over-Discharging Protection Delay Time 过放电保护延时 5.8 ±0.16V e). Over-Charge Current Protection : 过充电流保护： 4～9A f).
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 3.8 PCB description 线路板描述 3.8.1 布局图 3.8.2 顶层走线 3.8.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 4. Cell Specification 电芯规格：创明 3.7V/2600mAh 4.1 Model: CMICR18650F8-2600mAh 型号： CMICR18650F8-2600mAh 4.2 Cell Specification 电芯规格 表三 No. 序号 1 2 3 4 Items 项目 Charge Voltage 充电电压 Nominal Voltage 标称电压 Nominal Capacity 标称容量 Minimum Capacity 最小容量 5 Charge Current 充电电流 6 Standard Charging Method 标准充电方法 7 Charging Time 充电时间 8 9 10 11 12 13 Specifications 规格 4.2V 3.7V 2600mAh @0.2C Discharge(放电) 2500mAh @0.2C Discharge(放电) Standard charge: 0.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 4.3 Battery Cell Performance Criteria 电芯性能检查及测试 4.3.1 Electrical characteristics 电气性能 No. 序号 1 Items 项目 Test Method and Condition 测试方法与条件 Standard Charge 标准充电 Charging the cell initially with constant current at 0.2C and then with constant voltage at 4.2V till charge current declines ≤ 0.02C. 先用 0.2C 恒流充电至 4.2V ，再恒压 4.2V 充 电直至充电电流≤ 0.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 4.3.2 reliability 可靠性 表五 1 Vibration Test 振动测试 2 Drop Test 跌落测试 3 pressure test 挤压测试 4 External Short 外部短路 5 重物冲击 6 温度循环 After standard charging, fixed the cell to vibration table and subjected to vibration cycling that the frequency is to be varied at the rate of 1Hz per minute between 10Hz an 55Hz, the excursion of the vibration is 1.6mm. The cell shall be vibrated for 30 minutes per axis of XYZ axes.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 7 过压充电 8 欠压放电 温度转换时间不大于 30min; c) 再次将实验箱温度升为 75℃ ±2℃ ,温度转换 时间不大于 30min; d) 重复步骤 a~c,共循环 10 次。 将电池组按照 4.3.1 规定的试验方法充满电后,继 续以最大充电电流 2600mA 恒流充电至 12V,并保持 该电压进行恒压充电 1H。 将电池组按照 4.3.1 规定的试验方法充满电后,以 其最大放电电流 2600mA 恒流放电。电池组放电至 保护电路动作。放电后静置 10min,并继续按照 4.3.1 规定的试验方法充满电。 电池组应不起火、不爆 炸、不漏液。 电池组应不起火、不爆 炸、不漏液。 4.3.3 Visual Inspection 外观检查 There shall be no such defect as scratch, flaw, crack, and leakage, which may adversely affect commercial value of the cell.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 6. Safety warning/安全警告 a) Do not dismantle, open or shred secondary cells or batteries. 不要拆卸、打开或粉碎二级电池或电池。 b) In the event of a cell leaking, do not allow the liquid to come into contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 产品规格书 Product Specification Sheet 深圳海翼智新科技有限公司 CUSTOMER/客户： CUSTOMER P.N./客户料号： T8001 MODEL NO./产品型号： PA11 PRODUCT NO./产品编码： P0077-P2 REV1.1 REVERSION NO./版本： PREPARED DATE/拟制日期： 2018-07-05 CUSTOMER AUTHORIZED SIGNATURE/客户承认签核 PREPARED BY/拟 制: CHECKED BY/审 核: APPROVED BY/批 准: Please return to us one copy of “SPECIFICATION FOR APPROVAL” with you approved signature./客户确认签字，盖章后请回传一份承认书给我司.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD E. C. LIST/变更履历表 Rev. 版本 Description of Change/变更内容描述 Changed Remark Date/日期 /备注 Before/变更前 After/变更后 1.0 Original Release（初次发行） --- 2018.05.25 1.1 --- 更新外观图(更新贴纸) 2018.07.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD ** Table Of Content/目录 ** 1. Apply for Scope ……………………………………………………………………………………3 适用范围 2. Battery Specification …………………………………………… ………………………………3 电池规格 3. PCM Specification …………………………………………………………………………………7 保护板规格 4. Cell Specification ……………………………………………………… 电芯规格 5.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 1. Apply for Scope 适用范围 This specification describes the function of chargeable Li-ion polymer battery that made in GIANTSUN POWER CORPORATION. 本规格说明书描述了湖南炬神电子有限公司生产的可充电锂电池产品性能指标。 2. Battery Specification 电池规格：（本体高 66.8mm+出线长度 60.0±3mm）*37.5*19 SW18650-26HPA 3.65V/2600mAh 2pcs）。 7.3V/2600mAh 2.1 Shape Picture Content 电池外观图 2.1.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 2.2 Battery Specification Parameter: 电池参数规格 表一 No.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD No. 序号 15 16 17 18 19 20 21 Items 项目 Impedance Specifications 规格 ≤200mΩ. The impedance shall be measured at AC 1000 Hz initially. 内阻 Cycle Life 循环寿命 Pack Dimension 电池尺寸 Storage 储存 Warranty Time 质量保证期 Battery Weight 电池重量 Delivery voltage 出货电压 Charge the battery at 0.5C under 25℃until the battery voltage reaches 8.40V, and then charge it under the constant voltage until the current ≤0.02C. Stay it for 0.5h-1h, and then discharge it at 0.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 2.3 Safety Performance 安全性能 表二 No. 序号 1 2 3 Items 项目 Over-Charge Protection 过充保护 Test Method and Condition 测试方法与条件 At 20±5℃ conditions, after fast-charging, use an external 10V power to load the battery and last for 8 hours, then check the appearance of battery. 在环境温度(20±5)℃下, 电池快 速充电结束后,用电压为 10V 外接电源 持续给电池载入 8 小时，再检查电池外 观。 At20±5℃conditions,discharge battery to 5.8V with 0.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 3. PCM Specification 保护板规格 3.1 Electrical Characteristics (at RT=25℃ ) 电气性能 (在环境温度：25℃) A). Protection Criteria 保护规格 a). Over-Charging Protection Voltage: 过充保护电压: 8.56±0.05V b). Over-Charging Protection Delay Time: 过充电保护延时： 0.7～1.3S c). Over-Discharging Protection Voltage: 过放保护电压: d). Over-Discharging Protection Delay Time 过放电保护延时 5.8 ±0.16V e). Over-Charge Current Protection : 过充电流保护： 4～9A f).
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 3.2 Environmental Condition 环境条件 A). Operating Temperature Range: 充放电温度范围： Charge 充电： Discharge 放电： B). Storage Temperature Range: 存储温度范围： 0℃～+45℃ -20℃～+60℃ -5℃～+45℃ 3.3 At -20～60℃(Discharge) and 0℃～+45℃(Charge) conditions Battery protection performance shall be normal. 电池在-20～60℃（放电），0℃～+45℃（充电）环境温度内，电池保护性能是正常的. 3.4 Parts list 主要元件清单 NO.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 3.5.2 Discharge Performance at Low Temperature 低温放电性能 At -20±2℃ conditions, keep the battery for 2hrs, discharge the battery to 5.8V with 0.2C constant current， After keep the battery 2hrs at 20±5℃，then check the appearance of battery. 电池置于-20±2℃环温下 2 小时，然后以 0.2C 电流恒流放电至 5.8V，再放在 20±5℃环温下 2 小时 后，确认电池外观. --- The discharge capacity is above 80% of original capacity. The appearance is no distortion, no explosion, no leakage. ---放电容量是原始容量的 80%以上.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 3.8 PCB description 线路板描述 3.8.1 布局图 3.8.2 顶层走线 3.8.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 4. Cell Specification 电芯规格：振华 3.65V/2600mAh 4.1 Model: SW18650-26HPA-2600mAh 型号：SW18650-26HPA-2600mAh 4.2 Cell Specification 电芯规格 表三 No. 序号 1 2 3 4 Items 项目 Charge Voltage 充电电压 Nominal Voltage 标称电压 Nominal Capacity 标称容量 Minimum Capacity 最小容量 5 Charge Current 充电电流 6 Standard Charging Method 标准充电方法 7 8 9 10 11 12 13 Specifications 规格 4.2V 3.65V 2600mAh @0.2C Discharge(放电) 2500mAh @0.2C Discharge(放电) Standard charge: 0.5C 标准充电： 0.5C 0.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 4.3 Battery Cell Performance Criteria 电芯性能检查及测试 4.3.1 Electrical characteristics 电气性能 No. 序号 1 Items 项目 Test Method and Condition 测试方法与条件 Standard Charge 标准充电 Charging the cell initially with constant current at 0.5C and then with constant voltage at 4.2V till charge current declines ≤ 0.02C. 先用 0.5C 恒流充电至 4.2V ，再恒压 4.2V 充 电直至充电电流≤ 0.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 4.3.2 reliability 可靠性 表五 1 Vibration Test 振动测试 2 Drop Test 跌落测试 3 pressure test 挤压测试 4 External Short 外部短路 5 重物冲击 6 温度循环 After standard charging, fixed the cell to vibration table and subjected to vibration cycling that the frequency is to be varied at the rate of 1Hz per minute between 10Hz an 55Hz, the excursion of the vibration is 1.6mm. The cell shall be vibrated for 30 minutes per axis of XYZ axes.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 7 过压充电 8 欠压放电 温度转换时间不大于 30min; c) 再次将实验箱温度升为 75℃ ±2℃ ,温度转换 时间不大于 30min; d) 重复步骤 a~c,共循环 10 次。 将电池组按照 4.3.1 规定的试验方法充满电后,继 续以最大充电电流 2600mA 恒流充电至 12V,并保持 该电压进行恒压充电 1H。 将电池组按照 4.3.1 规定的试验方法充满电后,以 其最大放电电流 2600mA 恒流放电。电池组放电至 保护电路动作。放电后静置 10min,并继续按照 4.3.1 规定的试验方法充满电。 电池组应不起火、不爆 炸、不漏液。 电池组应不起火、不爆 炸、不漏液。 4.3.3 Visual Inspection 外观检查 There shall be no such defect as scratch, flaw, crack, and leakage, which may adversely affect commercial value of the cell.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 5.
湖南炬神电子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD Product Specification Sheet 產品規格書 CUSTOMER/客戶： 深圳海翼智新科技有限公司 CUSTOMER P.N./客戶料號： T8111 MODEL NO./產品型號： PA12A22 PRODUCT NO./產品編碼： P0078-P3 REVERSION NO./版本： 1.3 PREPARED DATE/擬制日期： 2018-08-15 CUSTOMER AUTHORIZED SIGNATURE/客户承认签核 PREPARED BY/拟 制: CHECKED BY/审 核: APPROVED BY/批 准: Please return to us one copy of “SPECIFICATION FOR APPROVAL” with you approved signature./客户确认签字，盖章后请回传一份承认书给我司.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD SPECIFICATION AMENDMENT RECORDS (規格變更記錄) Edition Description Date Approved 版本 描述 日期 審核 1.0 初始版本 2018.06.07 1.1 更新外观贴纸 2018.07.05 1.2 更新外观图及外观贴纸 2018.08.09 1.3 增加警告语 2018.08.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD Content 目錄 1. Apply for Scope ……………………………………………………………………………………4 適用範圍 2. Battery Specification ……………………………………………………………………………4 電池規格 3. PCM Specification …………………………………………………………………………………8 保護板規格 4. Cell Specification ………………………………………………………………………………10 電芯規格 5. Battery Appearance Dimension 電池外觀尺寸 6.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 1. Apply for Scope 適用範圍 This specification describes the function of chargeable Li-ion polymer battery that made in GIANTSUN POWER CORPORATION. 本規格說明書描述了湖南炬神电子有限公司生產的可充電鋰電池產品性能指標。 2. Battery Specification 電池規格：尺寸：67.85X38.25X38.25mm 7.2V/6700mAh （鋰電芯:LG 18650 3.6V/3350mAh 2.1 Shape Picture Content 電池外觀圖 2.1.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 2.2 Battery Specification Parameter: 電池參數規格 表一 No. Items Specifications 序號 項目 規格 1 2 3 4 5 6 7 8 Appearance 外觀 Nominal Voltage 標稱電壓 Nominal Capacity 標稱容量 Minimum Capacity 最小容量 Charge Voltage 充電電壓 Discharge Cut-off Voltage 放電截止電壓 Over-Charging Protection Voltage 過充保護電壓 Over-Discharging Protection Voltage 過放保護電壓 The surface is clear and no scratch, no mechanical abrasion, match well with the main machine 電池外表面清潔，無擦傷，無機械損傷，與主機配合良好 7.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD No. 序號 15 Items 項目 Specifications 規格 ≤300mΩ . The impedance shall be measured at AC 1000 Hz Impedance initially. 內阻 Charge the battery at 0.2C under 15℃~35℃ After 300 16 Cycles Cycle Life recoverabl 循环寿命 e capacity ≥ 75% 17 18 Length:电池本体 67.85±0.1mm； Width:38.25±0.1mm Thickness:38.25±0.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 2.3 Safety Performance 安全性能 表二 No. 序號 1 2 3 Items 項目 Test Method and Condition 測試方法與條件 At 20±5℃ conditions, after fast-charging, use an external 10V power to load the battery and last Over-Charge for 8 hours, then check the Protection appearance of battery. 過充保護 在環境溫度(20±5)℃下, 電池快 速充電結束後,用電壓為 10V 外接電源 持續給電池載入 8 小時，再檢查電池外 觀。 At20±5℃conditions,discharge battery to 5.6V with 0.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 3. PCM Specification 保護板規格 3.1 Electrical Characteristics (at RT=25℃ ) 電氣性能 (在環境溫度：25℃) A). Protection Criteria 保護規格 a). Over-Charging Protection Voltage: 過充保護電壓: 8.56±0.05V b). Over-Charging Protection Delay Time: 過充電保護延時： 0.7～1.3S c). Over-Discharging Protection Voltage: 過放保護電壓: d). Over-Discharging Protection Delay Time 過放電保護延時 5.6 ±0.16V 70～150ms e). Over-Charge Current Protection : 過充電流保護： 5～8A f).
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 3.2 Environmental Condition 環境條件 A). Operating Temperature Range: 充放电温度范围： Charge 充电： 0℃～+45℃ Discharge 放电： -20℃～+50℃ B). Storage Temperature Range: 存储温度范围： -20℃～+50℃ 3.3 At -20～50℃(Discharge) and 0℃～+45℃(Charge) conditions Battery protection performance shall be normal. 电池在-20～50℃（放电），0℃～+45℃（充电）环境温度内，电池保护性能是正常的。 3.4 Parts list 主要元件清單 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Designator Comment B+, VM1, B- Quantity 镍砖 4x4x0.3mm 3 0.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 3.5.2 Discharge Performance at Low Temperature 低溫放電性能 At -10±2℃ conditions, keep the battery for 2hrs, discharge the battery to 5.6V with 0.2C constant current， After keep the battery 2hrs at 20±5℃，then check the appearance of battery. 電池置於-10±2℃環溫下 2 小時，然後以 0.2C 電流恒流放電至 5.60V，再放在 20±5℃環溫下 2 小時 後，確認電池外觀. --- The discharge capacity is above 80% of original capacity. The appearance is no distortion, no explosion, no leakage. ---放電容量是原始容量的 80%以上.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 3.8 PCB description 線路板描述 3.8.1 布局图 3.8.2 顶层走线 3.8.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 4. Cell Specification 電芯規格：LG 3.63V/3350mAh 4.1 Model: LG LGABF1L1865 3350mAh PB 型號： LG LGABF1L1865 3350mAh PB 4.2 Cell Specification 電芯規格 表三 No. 序號 1 2 3 4 Items 項目 Charge Voltage 充電電壓 Nominal Voltage 標稱電壓 Nominal Capacity 標稱容量 Minimum Capacity 最小容量 5 Charge Current 充電電流 6 Standard Charging Method 標準充電方法 7 Charging Time 充電時間 8 9 10 11 12 13 Specifications 規格 4.2V 3.6V 3350mAh @0.2C Discharge(放電) 3250mAh @0.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 4.3 Battery Cell Performance Criteria 電芯性能檢查及測試 4.3.1 Electrical characteristics 電氣性能 No. 序號 Items 項目 1 Standard Charge 標準充電 2 Initial Capacity 初始容量 3 Cycle Life 循环寿命 4 5 6 Test Method and Condition 測試方法與條件 Charging the cell initially with constant current at 0.2C and then with constant voltage at 4.2V till charge current declines to 50mA. 先用 0.2C 恒流充電至 4.2V ，再恒壓 4.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 4.3.2 reliability 可靠性 表五 1 Vibration Test 振動測試 2 Drop Test 跌落測試 3 pressure test 挤压测试 4 External Short 外部短路 5 重物冲击 6 温度循环 After standard charging, fixed the cell to vibration table and subjected to vibration cycling that the frequency is to be varied at the rate of 1Hz per minute between 10Hz an 55Hz, the excursion of the vibration is 1.6mm. The cell shall be vibrated for 30 minutes per axis of XYZ axes.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 7 过压充电 8 欠压放电 温度转换时间不大于 30min; c) 再次将实验箱温度升为 75℃ ±2℃ ,温度转换 时间不大于 30min; d) 重复步骤 a~c,共循环 10 次。 将电池组按照 4.3.1 规定的试验方法充满电后,继 续以最大充电电流 3350mAh 恒流充电至 12V,并保持 该电压进行恒压充电 1H。 将电池组按照 4.3.1 规定的试验方法充满电后,以 其最大放电电流 3350mAh 恒流放电。电池组放电至 保护电路动作。放电后静置 10min,并继续按照 4.3.1 规定的试验方法充满电。 电池组应不起火、不爆 炸、不漏液。 电池组应不起火、不爆 炸、不漏液。 4.3.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 5.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO.
湖南炬神電子有限公司 HU NAN GIANTSUN POWER ELECTRONICS CO., LTD 6. Safety warning/安全警告 a) Do not dismantle, open or shred secondary cells or batteries. 不要拆卸、打开或粉碎二级电池或电池。 b) In the event of a cell leaking, do not allow the liquid to come into contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.
Safety Data Sheet According to HCS-2012 APPENDIX D TO §1910.1200 Version: 2.0/EN Revision date: 2018.01.01 Product name: Lithium metal battery Issue date: 2018.09.25 1. Identification (a) Product identifier Product name: Lithium metal battery (b) Other means of identification Product description: Model: CR123A Nominal Voltage: 3.0V Typical Capacity: 1400mAh Lithium content: 0.
Safety Data Sheet According to HCS-2012 APPENDIX D TO §1910.1200 Version: 2.0/EN Revision date: 2018.01.01 Product name: Lithium metal battery Issue date: 2018.09.25 Emergency Overview Signal word Danger Hazard Statements Harmful if swallowed Harmful in contact with skin Causes severe skin burns and eye damage Suspected of causing cancer Causes damage to organs through prolonged or repeated exposure This product is an article which contains a chemical substance.
Safety Data Sheet According to HCS-2012 APPENDIX D TO §1910.1200 Version: 2.0/EN Revision date: 2018.01.01 Product name: Lithium metal battery Issue date: 2018.09.
Safety Data Sheet According to HCS-2012 APPENDIX D TO §1910.1200 Version: 2.0/EN Revision date: 2018.01.01 Product name: Lithium metal battery Eye contact: Skin contact: Inhalation: Ingestion: Self-protection of the first aider Issue date: 2018.09.25 Show this safety data sheet to the doctor in attendance. Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. Keep eye wide open while rinsing. Remove contact lenses, if present and easy to do. Continue rinsing.
Safety Data Sheet According to HCS-2012 APPENDIX D TO §1910.1200 Version: 2.0/EN Revision date: 2018.01.01 Product name: Lithium metal battery Issue date: 2018.09.25 (c) Methods and materials for containment and cleaning up If the battery casing is dismantled, small amounts of electrolyte may leak. Collect all released material in a plastic lined container. Dispose off according to the local law and rules. Avoid leached substances to get into the earth, canalization or waters. 7.
Safety Data Sheet According to HCS-2012 APPENDIX D TO §1910.1200 Version: 2.0/EN Revision date: 2018.01.01 Product name: Lithium metal battery Skin and body Protection: Respiratory Protection: Hygiene Measures: Issue date: 2018.09.25 Not necessary under normal conditions, Wear protective gloves and protective clothing such as long sleeved clothing, impervious gloves, chemical resistant apron, and antistatic boots if handling an open or leaking battery. Not necessary under normal conditions.
Safety Data Sheet According to HCS-2012 APPENDIX D TO §1910.1200 Version: 2.0/EN Revision date: 2018.01.01 Product name: Lithium metal battery Issue date: 2018.09.25 Strong oxidizer, strong acid. (f) Hazardous decomposition products Under fire conditions, the electrode materials can form carcinogenic nickel and cobalt oxides. 11.
Safety Data Sheet According to HCS-2012 APPENDIX D TO §1910.1200 Version: 2.0/EN Product name: Lithium metal battery Revision date: 2018.01.01 Issue date: 2018.09.25 No information available. (c) Bioaccumulative potential No information available. (d) Mobility in soil No information available. (e) Other adverse effects No information available. 13.
Safety Data Sheet According to HCS-2012 APPENDIX D TO §1910.1200 Version: 2.0/EN Revision date: 2018.01.01 Product name: Lithium metal battery (f) Transport in bulk (according to Annex II of MARPOL 73/78 and the IBC Code) (g) Special precautions Issue date: 2018.09.25 No information available. No information available. 15. Regulatory information With regard to transport, the following regulations are cited and considered: - The International Civil Aviation Organization (ICAO) Technical Instructions.
