ETS Installation Guide For ETS8PS, ETS16PS, ETS16PR, and ETS32PR Multiport Device Servers Part Number 900-401 Revision A April 2005
Copyright and Trademark The information in this guide may change without notice. The manufacturer assumes no responsibility for any errors which may appear in this guide. AppleTalk, Chooser, and Macintosh are trademarks of Apple Computer Corp. LaserJet and Bitronics are trademarks of Hewlett Packard. Centronics is a registered trademark of Centronics Data Computer Corp. PostScript is a trademark of AdobeSystems, Inc. DEC and LAT are trademarks of Digital Equipment Corporation.
Disclaimer and Revisions This product has been designed to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against such interference when operating in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with this guide, may cause harmful interference to radio communications.
Contents 1: Introduction 7 Supported Serial Protocols _______________________________________________ 7 RS-232 ____________________________________________________________________ 7 RS-423 ____________________________________________________________________ 7 How to Use This Manual _________________________________________________ 8 2: Installation 9 ETSP Product Descriptions _______________________________________________ 9 ETSPS Front Panels _________________________________________________________
Contents 5: Printing on the ETS 25 LPR Printing __________________________________________________________25 LPR on Windows NT 3.5.
Contents Choosing the Right Software File__________________________________________ 56 Obtaining Software ____________________________________________________ 56 Via the Web _______________________________________________________________ 56 Via FTP __________________________________________________________________ 56 Reloading Software ____________________________________________________ 57 Reloading Sequence ________________________________________________________ 57 TCP/IP ______________________________
1: Introduction The Lantronix ETS (ETS8PS, ETS16PS, ETS16PR, and ETS32PR) is a multi-port device server providing shared network access to terminals, devices, console ports, and printers for a variety of network protocols and operating systems. The ETS supports the TCP/IP, IPX (NetWare), Local Area Transport (LAT), AppleTalk (EtherTalk), and Microsoft LAN Manager protocols. Note: In this manual, all ETS servers will be referred to as “the ETS” unless a distinction needs to be made between models.
Introduction How to Use This Manual 2:Installation Explains how to physically install the ETS. 3:Getting Started Explains the minimum configuration needed. 4:Using the ETS Explains some of the ways that you can use your ETS. 5:Printing on the ETS 6:NetWare Configuration 7:LAT Configuration 8:AppleTalk Configuration 9:DLC Configuration for LAN Manager Chapters 5 through 9 cover protocol-specific setup needed to install print queues and otherwise use the ETS.
2: Installation This chapter describes the various ETS models and shows how to install them into a basic network configuration. The ETSPS models will be explained first. For ETSPR descriptions and installation instructions, skip to ETSPR Product Descriptions. ETSP Product Descriptions ETSPS Front Panels The front panel of all ETSP models has a Test/Reset button (called Reset on the ETS8PS and ETS16PS), seven LEDs, and a power switch.
Installation Figure 2-1. ETS8PS and ETS16PS Back Panels ETS16PS Back Panel The back panel of the ETS16PS has a power plug, an AUI Ethernet port, a 10BASET Ethernet port, and 16 RJ45 serial ports. Figure 2-2. ETS16PS Back Panel Installing the ETSP The following two diagrams show properly-installed ETSP servers. Figure 2-3.
Installation To install the ETS, complete the following steps in order. Refer to the numbers in the previous figure. 1. Select a location for the ETS. When choosing a location, keep in mind the environmental restrictions discussed in E:Specifications. 2. Connect one or more serial devices to the ETS. Note: The default serial port settings are 9600 baud, 8 bit characters, no parity, 1 stop bit, and Xon-Xoff flow control. See C:Pinouts for information on what kinds of device attachments the ETS supports. 3.
Installation ETS32PR Front Panel The ETS32PR has 32 RJ45 serial ports, a Reset button, an AUI Ethernet port, an RJ45 Ethernet port for 10/100BASE-T, several status LEDs, and a power switch. Figure 2-5. ETS32PR Front Panel Note: The first RJ45 port is also the serial console port. Use it as a method for the initial setup or troubleshooting. ETSPR LEDs Each ETSPR has a total of 37 LEDs.
Installation Figure 2-6. Sample ETSPR Network Layout (ETS16PR shown) To install the ETS, complete the following steps in order: 1. Attach the two rack mount brackets to your ETS and attach your bracketed ETS to your rack. The brackets should go on both front corners or both rear corners. (This is only necessary if you would like to mount the unit on a rack.) Figure 2-7. Rack Mount Bracket Installation 2. Connect one or more serial devices to the ETS.
Installation a) It runs through a set of power-up diagnostics for approximately 12 seconds. The LEDs show varying patterns corresponding to the tests being run. b) It tries to obtain TCP/IP configuration information via DHCP, BOOTP, and RARP. This may take as long as 15 seconds if no hosts answer the requests. During this step, the OK LED blinks approximately 3 times per second and the NET LED blinks occasionally. 7. Install EZWebCon on your 32-bit Windows PC computer.
3: Getting Started It is important to consider the following points before logging into and configuring the ETS: You must configure the ETS IP address before any TCP/IP functionality is available. You cannot use the ThinWeb Manager until you have configured an IP address. Changing any server, service, or port setting requires privileged user status. The default privileged password is system. The login password is required for remote console logins. The default login username is access.
Getting Started Once you have connected to the ETS, you will see the Lantronix ThinWeb Manager interface. Use the left-hand menu to navigate to subpages where you can configure important settings as well as view statistics and other server information. Note: Do not use the ThinWeb Manager until the IP is configured. See TCP/IP Configuration. Figure 3-2. ThinWeb Manager Interface MENU Incoming Logins Incoming logins made via EZWebCon can be used to configure the ETS.
Getting Started b) For IP Address, enter the desired IP address to use for this ETS. The IP address should be on the same subnet as the PC running EZWebCon. c) For Subnet Mask, change the values provided only if you wish to use a mask other than the default. The default value should be correct in most cases. d) For Loadhost, enter the IP address of the loadhost where you intend to store your operating code. 3. Click OK. 4. Reboot the ETS. EZWebCon will let you know whether the configuration was successful.
Getting Started Type Help at the ‘Local_>’ prompt for assistance. Enter Username> gopher Local> SET PRIVILEGED Password> system (not echoed) Local>> DEFINE SERVER IPADDRESS 192.0.1.228 Local>> DEFINE SERVER SUBNET MASK 255.255.255.0 Any host wishing to access the ETS will have to be told the ETS’ IP address. This is typically configured in the UNIX file /etc/hosts or via a nameserver. Refer to the host’s documentation for additional information.
4: Using the ETS The sections in this chapter show how to use the ETS in a variety of applications. For detailed instructions on how to set up the ETS as a console server, see Console Server Example. For instructions on how to use the ETS in serial tunnel mode, see Serial Tunnel Example on page 23. For information about using the ETS with the Lantronix Comm Port Redirector, see Comm Port Redirector on page 24. Keep in mind that you must reboot the ETS after issuing a Define command.
Using the ETS In addition to direct Telnet connections, you can use the ETS’ built-in menu feature. The ETS menu allows you to connect to the IP address of the ETS and be greeted with a menu with which to connect to each attached serial device. Menu choices are an easy way to let users access often-used hosts and services without needing to know any ETS command syntax, the IP addresses of the non-local devices, or the socket numbers involved. Figure 4-2.
Using the ETS Figure 4-6. Menu Entries for manipulating the ETS Local>> DEFINE MENU 3 “HPUX Server” “connect local port_3” Local>> DEFINE MENU 4 “Linux Server” “connect local port_4” Local>> DEFINE MENU 5 “PBX Switch” “connect local port_5” To allow users to access a local service on the ETS, add a general ETS command. Figure 4-7. Menu Entries for manipulating the ETS Local>> DEFINE MENU 6 “ETS Prompt” “exit” Local>> DEFINE MENU 7 “Logout” “logout” NOTE: The Exit command only works in menu mode.
Using the ETS Figure 4-10. Configuring Switches Local>> Local>> Local>> Local>> DEFINE DEFINE DEFINE DEFINE PORT PORT PORT PORT 2-4 2-4 2-4 2-4 LOCAL SWITCH ^X FORWARD SWITCH ^F BACKWARD SWITCH ^B BREAK LOCAL Note: Define Port Break Local allows the ETS to recognize the switches you just configured. To check switch configurations, enter the Show/List Port command and specify the ports that are used for menu mode. Figure 4-11.
Using the ETS 4. To return to the menu from your Linux session, press the configured Local Switch key. In this case, the Local Switch is Ctrl-X (see Figure 4-10). Note: Switch keys only work within sessions. They do not work from the menu screen - you must enter a menu number to go to a session from the menu screen. Serial Tunnel Example Two ETS device servers can be connected to emulate a direct serial connection across a LAN or WAN.
Using the ETS UDP Configuration When the UDP protocol is used, there is no connection; each ETS must be told explicitly which hosts it is allowed to accept packets from. Each ETS would have to be configured to both send packets to and accept packets from the other ETS. ETS_A Local>> DEFINE PORT 2 DEDICATED TELNET 192.168.5.10:4096U Local>> DEFINE PORT 2 AUTOSTART ENABLED Local>> DEFINE PORT 2 ACCESS DYNAMIC ETS_B Local>> DEFINE PORT 3 DEDICATED TELNET 192.168.5.
5: Printing on the ETS The EZWebCon configuration software is the easiest method for ETS configuration. The following sections cover print configuration methods for TCP/IP hosts. Note: Printing directly to a port is the easiest method for printing to the ETS. If you would like instructions for printing to a service, see the Device Server Reference Manual located on the CD-ROM.
Printing on the ETS Creating a Standard TCP/IP port allows communication through a RAW Telnet port. This is supported by default. Creating a LPR port allowing jobs to be submitted to a “Service” offered by the ETS. Services are the basic method allowing the ETS to provide a queuing mechanism to a network host. (See the ETS Reference Manual for in-depth instructions on creating queues.) To enable LPR support, install Print Services for UNIX: 1.
Printing on the ETS 5. In the Add Port dialog box, enter the IP address of the ETS in the Printer Name or IP Address field. Enter a user-friendly name in the Port Name field. (Windows uses this as the display name for this printer configuration).
Printing on the ETS 6. In the Additional Information required dialog box, select Custom as the Device Type. Click Settings. 7. If configuring the printer to use a Standard TCP/IP port, select RAW. Identify the appropriate ETS port to use in the Port Number field.
Printing on the ETS Note: Lantronix uses the following convention to identify the TCP ports on the ETS: 3000 + port number. For example: Port 1 = 3001, Port 2 = 3002, Port 3 = 3003 etc. 8. If configuring the printer to use a LPR port, select LPR. Identify the appropriate ETS service to use in the Queue Name field. To determine the services running on the ETS do the following: Access the ETS Local> prompt (via telnet or a terminal console).
Printing on the ETS 11. Click Next. Click Finish. LPR on Windows NT 3.5.1 (and later) This section assumes that TCP/IP, Simple TCP/IP, and Microsoft TCP/IP printing have been installed on the Windows NT host. 1. In the Control Panel, double-click the Printers icon. 2. Double-click the Add Printer icon. 3. In the window that appears, choose My computer and click Next. 4. Select the Add Port button and click Next.
Printing on the ETS 5. Select LPR Port. Note: If LPR Port is not an option, open the Network Control Panel and add “Microsoft TCP/IP Printing” to the List of services. 6. Enter the name or IP address of your ETS on the first line, and enter the name of your ETS print service on the second line. 7. Select the manufacturer and printer type. 8. Enter the queue name.
Printing on the ETS 9. If applicable, choose Shared and select the type of operating system that the printer will be working with. (First confirm that the print queue is working). 10. Test the printer by choosing Yes and clicking Finish. LPR on Windows 95/98 Lantronix provides a utility to enable LPR printing on Windows 95/98. To request this utility, contact Lantronix Technical Support and ask for “ltxlpr.exe”. 1. Install the file ltxlpr.exe.
Printing on the ETS Figure 5-1. Adding /etc/hosts Entry xxx.xxx.xxx.xxx ETS_xxxxxx 2. Add the host print queue to the /etc/printcap file. The punctuation shown in Figure 5-7 is required, and no extra spaces should be added. Figure 5-2. Adding /etc/printcap Entry ets_prt|Printer on LAB ETS:\ :rm=ETS_xxxxxx:\ :rp=ETS_xxxxxx_TEXT:\ :sd=/usr/spool/lpd/ets_prt: This will create a host queue named ets_prt.
Printing on the ETS 4. From the dialog box that appears, choose remote. 5. From the next dialog box, choose Remote Printing. 6. The Add a Standard Remote Print Queue dialog box will appear. Enter the following information. The name of the print queue, The name of the ETS unit, The name of the ETS service, The type of print spooler on the remote server, and A description of the printer on the remote server. 7. A dialog box will appear: “Added print queue ets_prt”. Click Done.
Printing on the ETS 2. Answer the questions that follow. Figure 5-6. Configuring Remote Printer Remote Printing Configuration Enter information for remote printers or local printers accepting remote printing requests Please enter the printer name (q to quit): backupprinter Is printer backupprinter a remote printer or a local printer? (r/l) r Please enter the name of the remote host that backupprinter is attached to: ETS_xxxxxx The backupprinter is connected to host ETS_xxxxxx.
Printing on the ETS Unix Host Troubleshooting Table 5-1. TCP Troubleshooting 36 Area to Check Explanation The ETS IP address and name are entered in the host file. Telnet to the ETS using the name in the host file and verify that the ETS name is resolvable and that the ETS is reachable via the network.
6: NetWare Configuration The EZWebCon configuration software is the easiest way to configure the ETS. The following sections cover print configuration methods for NetWare hosts. Note: The ETS needs an IP address before you can use EZWebCon. See TCP/IP Configuration on page 16 for instructions. This chapter explains creating NDS print queues with NetWare Administrator and with the PCONSOLE Quick Setup option. To create NDS print queues, you must be running NetWare version 4.x with NDS capabilities.
NetWare Configuration Figure 6-2. Defining Directory Service Tree Local>> DEFINE PROTOCOL NETWARE DSTREE foodco Note: For an explanation of the structure of the NetWare Directory Service tree, see your host documentation. 3. Define the directory service context in which the ETS is located. Figure 6-3. Defining Directory Service Context Local>> DEFINE PROTOCOL NETWARE DSCONTEXT ou=kiwi.ou=exotic.o=fruit 4.
NetWare Configuration 3. From the main menu, choose Quick Set-Up. 4. When prompted by PCONSOLE, enter the information with which to configure the print queue. The print server name (ETS_xxxxxx), The new printer name (service name, such as ETS_xxxxxx), The new print queue name, and The print queue volume (the name of the file server from which the printer receives print requests). The remaining fields can be left in their default settings. 5. Press the F10 key to save the print queue information.
NetWare Configuration Area to Check Explanation The DSTree, DSContext, and DSLicense Type Show Protocol NetWare NDS. This command shows the tree and the context that you have configured, a failure code, and an NDS error code for each server. DSTree is the directory service tree on which the ETS is located. DSContext is the context where the ETS is located; it must match the context on the file server (The DSContext must be of the following form: ou=fruit.o=exotic). DSLicensed should be yes.
NetWare Configuration Bit Meaning Remedy 7 Authentication failed Ensure the ETS login password is the same as the print server object password. If the ETS is using the default password (access), there should be no print server object password.
7: LAT Configuration The EZWebCon configuration software is the easiest way to configure the ETS. The following sections cover print configuration methods for LAT hosts. Note: The ETS needs an IP address before you can use EZWebCon. . To use LAT you must obtain a LAT license from your dealer or Lantronix and use the Set/Define Protocol LAT License command on your ETS. LAT print queues can be created by printing to a port or printing to a service. Printing directly to a port requires no ETS configuration.
LAT Configuration Figure 7-4. Translating LAT Error Codes $ SHOW QUEUE/FULL/ALL queue_name (note the error code nnnnnnnn) $ SET MESSAGE SYS$MESSAGE:NETWRKMSG.EXE $ EXIT %Xnnnnnnnn Table 7-1. Troubleshooting LAT Configurations Using a Port Area to Check Explanation The specified node name matches the ETS node name Use the Show Server command to verify. The specified port name matches the port’s name Use the List Port 1 command to verify. Table 7-2.
8: AppleTalk Configuration The EZWebCon configuration software is the easiest way to configure the ETS. The following sections cover print configuration methods for AppleTalk hosts. Note: The ETS needs an IP address before you can use EZWebCon. Note: Macintoshes that do not support EtherTalk will need either an Ethernet card or a LocalTalk-to-EtherTalk router to use the ETS.
AppleTalk Configuration AppleTalk Host Troubleshooting Table 8-1. AppleTalk Host Troubleshooting Area to Check Explanation The printer is available to be selected in the Chooser Make sure the printer is in the right zone. Bidirectional communication Lock the printer in PostScript mode and issue the Test Service PostScript Count n command. This sends a job to the printer and waits for the response.
9: DLC Configuration for LAN Manager The EZWebCon configuration software is the easiest way to configure the ETS. This chapter explains DLC/Digital Network Port configuration for Windows NT 4.x hosts. Note: The Server needs an IP address before you can use EZWebCon. Printing using an LPD client is the preferred method for sending print jobs to the ETS. Windows 95 does not support DLC printing (see 5:Printing on the ETS for more information).
A: Contact Information If you are experiencing an error that is not described in this book, or if you are unable to fix the error, you may: To check our online knowledge base or send a question to Technical Support, go to http://www.lantronix.com/support. Email us at support@lantronix.com. Call us at: (800) 422-7044 Domestic (949) 453-7198 International (949) 450-7226 Fax Our phone lines are open from 6:00AM - 5:30 PM Pacific Time Monday through Friday excluding holidays.
B: Troubleshooting This appendix discusses how to diagnose and fix errors quickly yourself without having to contact a dealer or Lantronix. It will help to connect a terminal to the serial port while diagnosing an error to view any summary messages that are displayed. When troubleshooting, always ensure that the physical connections (power cable, network cable, and serial cable) are secure. Note: Some unexplained errors may be caused by duplicate IP addresses on the network.
Troubleshooting Problem/Message The terminal shows a Boot> prompt rather than a Local> prompt. The ETS passes powerup diagnostics, but attempts to download new Flash ROM code from a network host. Error Remedy A rapidly-blinking OK LED may signal boot failure. Reboot the unit. When the ETS is running normally, the OK LED blinks every two seconds. The ETS is not connected properly to the Ethernet. Ensure that the ETS is firmly connected to a functional and properly-terminated network node.
Troubleshooting Area to Check Explanation The ETS is in the loadhost’s /etc/hosts file The ETS must be in this file for the host to answer a BOOTP or TFTP request. The download file is in the correct directory and is world-readable The download file must be in the correct directory and world-readable. Specify the complete pathname for the download file in the BOOTP configuration file, or add a default pathname to the download filename.
Troubleshooting Figure B-1. BCP Command Examples Boot> SET IPADDRESS 192.0.1.229 Boot> SET SOFTWARE /tftpboot/ETS*.SYS Boot> SET LOADHOST 192.0.1.188 Boot> SET SECONDARY 192.0.1.22 Boot> FLASH % Initialization begins in 5 seconds..... These commands set the Server’s address, the software loadfile, and the loadhost’s IP address (as well as that of a backup loadhost). The server then reboots using the Flash command and will attempt to load the file ETS*.SYS from the host at 192.0.1.188.
Troubleshooting SET RARP {Enabled, Disabled} Enables or disables the sending of RARP queries during the boot sequence. It is enabled by default. SET Secondary ip_address Specifies a backup loadhost. The IP address should be in standard numeric format (no text names are allowed). The backup loadhost will be queried if the primary host cannot load the server. SET Software filename Specifies the name of the file to load. The ETS will automatically add .SYS to the filename you specify.
C: Pinouts Ethernet Connector Figure C-1. RJ45 Ethernet Connector RJ45 Serial Connectors ETS servers are RS-423 compliant, and are thus limited by the equipment at the remote end of the serial line. If the port is connected to an RS-232 device, it is subject to RS-232 limits: 15m (50 ft.) in length at 9600 baud, and to 2m (6 ft.) at 115.2K baud, although longer lengths will generally work. Figure C-2.
Pinouts Figure C-3. Pinouts of RJ45-DB25 Connections The arrows in Figure C-3 represent the direction of the signal. The pinouts assume that the 8-conductor cable connecting the ETS and the adapter block is a swapped/ rolled serial cable. Both the transmit and receive ground signals on the ETS connector are wired to the signal ground on a DB25 adapter. Figure C-4.
Pinouts Figure C-5. Wire Splicer To splice the wires, cut off the end of the wire that does not extend through the connector and insert both wires into the connector. Make sure that the wire that does not extend through the connector is in as far as possible to ensure a solid connection. Make sure that the wire that does extend through the connector extends far enough on the other side to be inserted in to the DB25 connector.
D: Updating Software Choosing the Right Software File Lantronix intends to provide multiple software files for the ETS models. Each software file will contain the core ETS operating code for that particular model. Table D-1. Available ETS Software Software File Name Models Supported ETS.SYS Old, do not use this file ETSP.SYS ETS8P, ETS16PS ETS16PR.SYS ETS16PR ETS32PR.SYS ETS32PR Obtaining Software Current software files (ETS*.SYS) are available on the distribution CD.
Updating Software Figure D-1. Sample FTP Login 230-Welcome to the Lantronix FTP Server. 230230-IMPORTANT: Please get the README file before proceeding. 230-IMPORTANT: Set BINARY mode before transferring executables. 220230-Direct questions to support@lantronix.com or 800-422-7044 (US) 230230 Guest login ok, access restrictions apply. Remote system type is [your type will be displayed here].
Updating Software Some BOOTP and TFTP implementations require a specific directory for the ETS*.SYS file. See your host’s documentation for instructions. To manually configure the ETS IP parameters for software reload, use the following commands. Figure D-2. Configuring TCP/IP Reload Local> SET PRIVILEGED Password> SYSTEM (not echoed) Local>> DEFINE SERVER IPADDRESS nnn.nnn.nnn.nnn Local>> DEFINE SERVER SOFTWARE “/tftpboot/ETS*.SYS” Local>> DEFINE SERVER LOADHOST nnn.nnn.nnn.
Updating Software Troubleshooting Flash ROM Updates Many of the problems that occur when updating the Flash ROM can be solved by completing the following steps: Table D-2. Flash ROM Troubleshooting Area to Check Explanation NetWare Ensure the file is in the login directory. Since the ETS cannot actually log into the file server, it has very limited access to the server directories. TFTP Check the file and directory permissions.
E: Specifications Power Information Power Requirements Voltage: 95 - 250 Volts AC, 3-wire single phase, auto-ranging Frequency: 47-63 Hz Operating Current: 300 mA @ 120 V Power Consumption: 40 Watts (maximum) Fuse Rating: 1.6A, 250 Volts Power Supply Cord Cord type: 3 conductors, 1.0 mm2 minimum conductor size (approximately 18 AWG) Rated for: 250 Volts AC, 10 Amps Length: 3.
F: Frequently-Used Commands This appendix lists some of the most frequently-used commands of the Multiport Device Server command set. More information about the command set, including additional options, can be found in the Device Server Reference Manual located on the CD-ROM and available for download from http://lantronix.com/support/download/index.html. Conventions Please note the following before continuing: Commands are divided into Server (general), Port, and Protocol sections.
Frequently-Used Commands Command Option(s) Description DEFINE SERVER GATEWAY ipaddr Specifies the host to be used as a TCP/IP gateway to forward packets between networks. Enter an IP address. DEFINE SERVER INCOMING option Enables incoming LAT and Telnet connections. BOTH LAT Enables only incoming LAT connections. NONE Disables incoming connections. TELNET Enables only incoming Telnet connections. PASSWORD Causes the ETS to prompt for a password for all incoming connections.
Frequently-Used Commands Command Option(s) Description RTEL {EN/DIS} DEFINE SERVICE “name” option DEFINE SERVICE “name” option INITIALIZE option LOGOUT option PURGE SERVICE option DLC {EN/DIS} Specifies which service will handle print requests from DLC hosts. DLC can be enabled on one service per ETS. BANNER {EN/DIS} When Enabled, causes the ETS to print a banner page before jobs. BINARY {EN/DIS} When Enabled, the ETS will not process data passed through the service.
Frequently-Used Commands Command {SHOW/MONITOR} SERVICE option ZERO COUNTERS option Option(s) Description COUNTERS Displays characteristics related to the various counters kept by the ETS. Displays characteristics about all configured services once (Show) or continually every three seconds (Monitor). “service” Displays only characteristics related to the named service. ALL Zeroes all port, node, and server counters. PORT num Zeroes port counters for the specified port.
Frequently-Used Commands Command Option(s) Description {SHOW/MONITOR} PORT 2 Displays the port’s configuration characteristics once (Show) or continually every three seconds (Monitor). Counters and Status keywords can be added. TEST PORT 2 option COUNT rows WIDTH cols Sends an ASCII data stream to the port for the specified number of rows and/or columns. POSTSCRIPT Sends a PostScript test page to the port.
Frequently-Used Commands Command NETWARE ENCAPSULATION option {EN/DIS} Option(s) Description ETHER_II Configures the ETS to use Ethernet v2 frame format. 802_2 Configures the ETS to use 802.2 frame format with NetWare SAPs. SNAP Configures the ETS to use 802.2 frame format with SNAP SAPs. DEFINE PROTO NETWARE LOADHOST server See DEFINE SERVER NETWARE LOADHOST server. PURGE IPSECURITY option ALL Removes the entire IP security table.
G: Compliance and Warranty Information Declaration of Conformity (according to ISO/IEC Guide 22 and EN 45014) Manufacturer’s Name & Address: Lantronix 15353 Barranca Parkway, Irvine, CA 92618 USA Declares that the product: Product Name: Terminal Server Model Name/Number: ETS8PS ETS16PS ETS16PR ETS32PR Conforms to the following standards or other normative documents: Safety: EN 60950:1988 + A1, A2 Electromagnetic Emissions: EN55022: 1998 (CISPR 22, Class A: 1993, A1 1995, A2: 1996) IEC 1000-3-2/A14:
Compliance and Warranty Information Warranty Lantronix warrants each Lantronix product to be free from defects in material and workmanship for a period of ONE YEAR. During this period, if a customer is unable to resolve a product problem with Lantronix Technical Support, a Return Material Authorization (RMA) will be issued. Following receipt of a RMA number, the customer shall return the product to Lantronix, freight prepaid.
