Model 4340 Digital Camera System (CCTV) User Manual Archived 6/3/13
ETS-Lindgren L.P. reserves the right to make changes to any product described herein in order to improve function, design, or for any other reason. Nothing contained herein shall constitute ETS-Lindgren L.P. assuming any liability whatsoever arising out of the application or use of any product or circuit described herein. ETS-Lindgren L.P. does not convey any license under its patent rights or the rights of others. © Copyright 2007–2012 by ETS-Lindgren L.P. All Rights Reserved.
Table of Contents Notes, Cautions, and Warnings ................................................ v 1.0 Introduction .......................................................................... 7 Standard Configuration and Components ................................................... 7 Optional Configurations and Additional Components ................................ 10 If You Have a Chamber With A Shielded Control Room .................... 10 If You Have a Tripod Mount ......................................
Chamber With Shielded Control Room—Additional Pre-installation Tasks ................................................................................................ 35 Chamber With Shielded Control Room—Installation Tasks ............... 35 If You Have a Tripod Mount (For Use with or without Shielded Control Room)....................................................................................................... 37 Tripod Mount—Additional Pre-Installation Tasks ...............................
Notes, Cautions, and Warnings Note: Denotes helpful information intended to provide tips for better use of the product. Caution: Denotes a hazard. Failure to follow instructions could result in minor personal injury and/or property damage. Included text gives proper procedures. Warning: Denotes a hazard. Failure to follow instructions could result in SEVERE personal injury and/or property damage. Included text gives proper procedures.
This page intentionally left blank.
1.0 Introduction The ETS-Lindgren Model 4340 Digital Camera System (CCTV) is designed to monitor tests conducted in anechoic or reverb chambers and large test cells where moderate EMI field strengths are present. Depending on the configuration, the camera is connected to a personal computer outside the chamber by either Ethernet or fiber optic cables. When the camera and computer are on, the camera image displays in a browser window at the computer.
Archived 6/3/13 8 | Introduction
The standard configuration for the Model 4340 CCTV includes these components: Toshiba Network Camera 1K-WB21A—Includes Ethernet cable and power cable connected to camera. Shielded camera enclosure with dome—Includes camera penetration connected to enclosure, and absorber wrap for the enclosure.
Optional Configurations and Additional Components Following are the optional configurations for the Model 4340 CCTV, including a list of additional components required to install the configuration. For diagrams and more information on installing an optional configuration, see Install Optional Components on page 33.
IF YOU HAVE A MULTI-CAMERA SYSTEM For use with or without a shielded control room. You need these additional components: The number of cameras in a multi-camera configuration may require additional components other than those in the following list. Please contact ETS-Lindgren to configure a multi-camera system.
Power Supply Options The 10/100 Ethernet filter provides the power for all configurations except the tripod mount, which is powered by a battery pack. 10/100 ETHERNET FILTER See the 10/100 Ethernet Filter Installation Manual for all filter information and installation instructions. They are not included in this document. BATTERY PACK AND CHARGER The tripod mount configuration is powered by a battery pack. The battery pack contains a 12V 13Ah Nickel-Metal Hydride (NiMH) battery housed in a shielded case.
H-491009 Tripod The H-491009 tripod includes a 1/4–20 thread center pole and a 3/8-inch thread center pole. Use the 3/8-inch thread center pole to mount the camera onto the tripod. This dielectric tripod is the preferred method for mounting field probes for making unperturbed field measurements. It includes a 1/4–20 UNC threaded stud for mounting any ETS-Lindgren probe with a tripod mount. It is designed with an adjustable center post and a rotating mount.
INSTALLATION AND SETUP CHECKLIST Complete pre-installation tasks—See page 23. Install the 10/100 Ethernet filter—See page 25. Mount the camera—For wall or ceiling mount, see page 29. For tripod mount, see page 37. Install optional items—See page 33. Set up the computer—See page 47. Operate the camera—See page 49.
2.0 Maintenance Before performing any maintenance, follow the safety information in the ETS-Lindgren Product Information Bulletin included with your shipment. Maintenance of the Model 4340 CCTV is limited to external components such as cables or connectors. WARRANTY Servicing or modifying the camera without ETS-Lindgren authorization may void your warranty. There are no internal user serviceable items. Only qualified personnel should service this equipment. Contact ETS-Lindgren for service.
Replacement and Optional Parts ETS-Lindgren may substitute a similar part or new part number with the same functionality for another part/part number. Contact ETS-Lindgren for questions about part numbers and ordering parts. Following are the part numbers for ordering replacement or optional parts for the Model 4340 CCTV.
Part Description Part Number DCCTV System, Tripod Configuration, for use with or without shielded control room—Does not include computer, does not include computer monitor 4340-03XPC DCCTV Camera, Pan and Tilt 111095 LMF-4095 10/100 Ethernet Filter, for use without shielded control room, includes internal fiber optic-to-Ethernet converter E-LMF-4095 LMF-4106 10/100 Ethernet Filter, for use with shielded control room, includes external fiber optic-to-Ethernet converter E-LMF-4106 Computer, DCCTV Mo
This page intentionally left blank.
3.0 Specifications Camera Enclosure, Converter Enclosure, Dome The converter enclosure is included only with a tripod configuration. Enclosure/Dome Shielding: Up to 200 Volts per meter (V/m) 14°F to 104°F Operating Temperature: (–10°C to 40°C) Height: 7.82 cm (3.08 in) Dome Dimensions Radius: 7.82 cm (3.08 in) Diameter: 16.57 cm (6.525 in) Camera Enclosure Dimensions Height: 9.685 cm (3.813 in) Microphone Camera Enclosure Connectors: Line-out Diameter: 21.9 cm (8.
Battery Pack and Charger The battery pack and charger are included only with a tripod configuration. Width: 12.7 cm (5.0 in) Length: 25.4 cm (10.0 in) Battery Pack Dimensions: Height (with handle): 17.18 cm (6.765 in) Height (without handle): 12.28 cm (4.835 in) 12V 13Ah Nickel-Metal Hydride (NiMH), rechargeable Battery Type: Archived 6/3/13 20 F battery pack, 13000 mAH (rapid charge cells, 1.
Toshiba Network Camera 1K-WB21A For a complete list of camera specifications, see the Toshiba IK-WB21A Network Camera Advanced User’s Guide. SXVGA: 1280 x 960 Image Size: Maximum Frames Per Second (FPS): VGA: 640 x 480 (default) SXVGA: 7.
14°F to 104°F Operating Temperature: (–10°C to 40°C) Width: 11.37 cm (4.48 inches) Height: 13.58 cm (5.35 inches) Physical Dimensions: Length: 11.37 cm (4.48 inches) Weight: 716.67 grams (1.
4.0 Pre-Installation Tasks Before installing any components, follow the safety information in the ETS-Lindgren Product Information Bulletin included with your shipment. Prior to installing the Model 4340 Digital Camera System (CCTV), complete these pre-installation tasks. If you are installing one of the optional configurations listed under Optional Configurations and Additional Components on page 10, additional pre-installation tasks may be required.
Choose the Camera Location You will install the 10/100 Ethernet filter on the outside of the chamber at the source of power, and the camera will mount to the filter penetration inside the chamber. Verify that the view from the selected location is obstruction-free, especially if absorber cones are in the vicinity. A tripod-mounted camera receives power from the battery pack, so a 10/100 Ethernet filter is not provided.
5.0 Install the 10/100 Ethernet Filter Before installing any components, follow the safety information in the ETS-Lindgren Product Information Bulletin included with your shipment. See the 10/100 Ethernet Filter Installation Manual for the pre-installation requirements and installation instructions for the filter. They are not included in this document. If you do not install an on/off power switch, the camera is powered on at all times.
Overview of 10/100 Ethernet Filter Connections Overview of 10/100 Ethernet Filter Operation Following is an overview of the functions of the 10/100 Ethernet filter. To see the locations of the referenced connections and components, refer to the diagram on page 26. 1. Archived 6/3/13 26 AC power enters the 10/100 Ethernet filter, and then enters the power supply module, where the AC power is converted to 12V DC power.
2. 3. Clean DC power emerges from the filter module to the clean side of the 10/100 Ethernet filter as two connectors: Power connector for camera—The power cable from the camera plugs into this power connector. Power connector for Ethernet-to-fiber optic converter—This power connector plugs into the converter. The Ethernet cable from the camera also plugs into the converter.
2. Turn the top of the strain relief until the strain relief is loosened from the power cord. 3. Remove the terminal ring and spade lugs from filter. 4. Remove the cord from the filter. 5. Replace with a Schuko plug and cord. 6. Using the provided spare terminal ring and spade lugs, wire the ground wire and power wires, as required. 7. Tighten the strain relief around the power cord, and replace the access cover.
6.0 Wall or Ceiling Mount the Camera Before installing any components, follow the safety information in the ETS-Lindgren Product Information Bulletin included with your shipment. Before you mount the camera, complete the installation of the 10/100 Ethernet filter. See the 10/100 Ethernet Filter Installation Manual for the pre-installation requirements and installation instructions for the filter. They are not included in this document.
3. Connect the assembled pipe to the filter penetration with a pipe-to-pipe coupler, running the cables through the penetration to the 10/100 Ethernet filter outside the chamber. Manually tighten the coupler to secure the pipe. 4. Connect the camera enclosure to the assembled pipe. If wall-mounting the camera, screw the camera penetration onto the elbow joint at the end of the pipe. Tighten the locking nut with a wrench.
If mounting the camera from the ceiling, connect the camera penetration to the pipe with a pipe-to-pipe coupler. Manually tighten the coupler, and then tighten the locking nut with a wrench. When the camera enclosure is completely connected to the pipe, the ETS-Lindgren label on the enclosure should point to the center of the desired field of vision. 5.
6. Plug the Ethernet cable from the camera into the connector on the Ethernet-to-fiber optic converter in the 10/100 Ethernet filter, and then plug the power cable from the camera into the keyed power connector cable from the converter. For a diagram of filter connections, see page 26. 7. Provide additional shielding by encircling the enclosure and assembled pipe with the provided absorber wrap. To install optional components, see page 33. To set up the computer, see page 47.
7.0 Install Optional Components Before installing any components, follow the safety information in the ETS-Lindgren Product Information Bulletin included with your shipment. To install the following configurations and components: If you have a chamber with a shielded control room—See the next section. If you have a tripod mount (for use with or without a shielded control room)—See page 37. If you have a multi-camera system (for use with or without a shielded control room)—See page 42.
Archived 6/3/13 34 | Install Optional Components
CHAMBER WITH SHIELDED CONTROL ROOM—ADDITIONAL PRE-INSTALLATION TASKS Install the fiber optic feedthrough connectors in the wall of the shielded control room. CHAMBER WITH SHIELDED CONTROL ROOM—INSTALLATION TASKS 1. Remove the access cover.
Your 10/100 Ethernet filter may have shipped with an external fiber optic-to-Ethernet converter, and the fiber optic cables connected internally. If so, skip step 2 and step 3 in the following instructions. 2. Disconnect the fiber optic cables from the fiber optic-to-Ethernet converter. Plug the cables into the internal fiber optic connectors. 3. Remove the fiber optic-to-Ethernet converter from the 10/100 Ethernet filter. 4.
If You Have a Tripod Mount (For Use with or without Shielded Control Room) A tripod mount configuration requires you install a tripod, battery pack, fiber optic-to-Ethernet converter, an Ethernet cable, fiber optic cables, and fiber optic feedthrough connectors. The fiber optic-to-Ethernet converter is housed in the shielded enclosure attached to the camera enclosure, requiring no additional assembly. See the diagram on the following page. To set up the computer, see page 47.
Archived 6/3/13 38 | Install Optional Components
TRIPOD MOUNT—ADDITIONAL PRE-INSTALLATION TASKS Install the fiber optic feedthrough connectors in the wall of the chamber. If you have a shielded control room, also install fiber optic feedthrough connectors in the wall of the control room. TRIPOD MOUNT—INSTALLATION TASKS The H-491009 tripod includes a 1/4–20 thread center pole and a 3/8-inch thread center pole. Use the 3/8-inch thread center pole to mount the camera onto the tripod.
While performing the following steps, always protect and support the camera and camera enclosure. Do not roll, jar, or drop the camera and camera enclosure. ETS-Lindgren is not responsible for damage to the camera as a result of improper handling. 1. Set up the tripod in the chamber. 2. Remove the 3/8-in thread center pole from the tripod by rotating the height adjuster knob to loosen, and then lifting the pole up.
3. Place the camera and camera enclosure in a stable location to prevent it from rolling or falling. Securely support the camera and enclosure, and rotate the 3/8-in thread center pole into the threaded connector on the bottom of the enclosure. 4. Supporting the camera and enclosure, carefully re-insert the 3/8-in thread center pole into the tripod. When the center pole is at the desired height, rotate the height adjuster knob to tighten. 5.
If You Have a Multi-Camera System (For Use with or without Shielded Control Room) In addition to mounting the cameras from the wall or ceiling, a multi-camera configuration without a shielded control room requires you to install a 10/100 network switch and Ethernet cables. See the diagrams on the following pages. To set up the computer for a multi-camera system, see Computer Setup on page 47 and Viewing Images from a Multi-Camera System on page 48.
Archived 6/3/13 Install Optional Components | 43
If you have a shielded control room, also install a 10/100 network switch, one fiber optic-to-Ethernet converter per camera, Ethernet cables, fiber optic cables, and fiber optic feedthrough connectors.
MULTI-CAMERA SYSTEM—ADDITIONAL PRE-INSTALLATION TASKS For a multi-camera configuration, you will need to install one 10/100 Ethernet filter per camera, in addition to mounting the cameras. Install filters— Follow the 10/100 Ethernet filter installation instructions in the separate document, 10/100 Ethernet Filter Installation Manual. They are not included in this document. Mount cameras—Follow the instructions to wall-mount or ceiling-mount a camera on page 29.
3. If you do not have a shielded control room— Plug one Ethernet cable for each camera into any of the numbered connectors on the network switch. Run each cable to a 10/100 Ethernet filter. Plug the cable into the external Ethernet connector on the 10/100 Ethernet filter. For a diagram of filter connections, see page 26.
8.0 Computer Setup Before connecting any components, follow the safety information in the ETS-Lindgren Product Information Bulletin included with your shipment. Minimum Computer Requirements If you purchased a Model 4340 Digital Camera System (CCTV) configuration from ETS-Lindgren that includes a personal computer, the following requirements are met.
3. Follow the computer instructions to turn on the computer. 4. Internet Explorer automatically loads, links to the IP address of camera, and displays the current view from the camera. Viewing Images from a Multi-Camera System There are two options for viewing the images from multiple cameras: Multi Windows—This setting opens a separate Internet Explorer window for each camera. Each window can be individually resized as required.
9.0 Operation Before connecting any components, follow the safety information in the ETS-Lindgren Product Information Bulletin included with your shipment. Operating Notices Before placing the Model 4340 Digital Camera System (CCTV) into service, follow these precautions: Never face the camera towards any bright or reflective light. This may cause a smear on the picture and possible damage to the charge-coupled device (CCD).
Viewing Images from the Camera When the camera is powered on, it will take up to one minute to start up. To view an image from the camera, simply turn on your computer. With the current view from the camera displayed in Internet Explorer®: 1. Click on the area of the screen that you want to view, and the camera pans and tilts to the specified area. 2. Zoom in and out on the current view by rotating the roller wheel on the mouse.
5. Open a second Internet Explorer browser window and type the next IP address. Repeat this step until you open a browser window for each camera on the network. 6. Arrange browser windows. Drag windows to desired location on monitors. Re-size windows as required. Setting Resolution & Frame Rate For high frame rates (greater than 7.5 frames per second), do not exceed 640x480 resolution. Archived 6/3/13 1. Power up all cameras. Allow cameras to complete self-test routine. 2.
Operating the Battery Pack You must charge the battery pack before using it for the first time. See Charging the Battery Pack on page 55 for complete charging information. USING THE BATTERY PACK The power button located on the battery pack functions as an on/off switch for the battery pack and the camera. When you are using the camera or charging the battery pack, the button should be in the on position. When the camera is off or the battery pack is in storage, the button should be in the off position.
Turn off the battery pack before connecting or disconnecting cables. To turn the battery pack on—Push the power button in to depress the button. In this position, the battery pack will continuously supply power. Select this setting to use the camera. To turn the battery pack off—Push the power button in and then release it to the off position. In this position, the battery pack will not supply power. Select this setting to turn off the camera or to place the battery pack into storage.
STORING THE BATTERY PACK Make sure the power button is in the off position before storing the battery pack. Fully charge the battery pack before placing it into storage. When storing it for an extended period of time, charge the battery pack once per month. Over time the battery pack will slowly discharge, and permanent damage could occur if the battery pack completely discharges. ETS-Lindgren is not responsible for damage to the battery pack as a result of improper handling and care.
CHARGING THE BATTERY PACK You must charge the battery pack before using it for the first time. You may charge the battery pack inside or outside the chamber. If charging the battery pack inside the chamber, do not perform any testing while charging is in progress. The battery pack normally provides up to 12 hours of operation, but operating time may be reduced with extensive use of the pan and tilt and functions. It can take up to 24 hours to fully charge the battery pack. Following are the steps: 1.
4. Slide the selector switch on the battery charger to 1.8A. 5. Connect the battery charger to a mains supply (100 or 240 VAC). 6. Turn on the mains supply. The charge light on the battery charger will illuminate red, indicating a charge is in progress. Continue charging until the charge light illuminates green, indicating a full charge.
REPLACING THE BATTERY PACK At end of useful life, please recycle the used batteries, or dispose of them safely and properly. Many cities collect used batteries for recycling or disposal. You may contact your local waste disposal agency for information on battery recycling and disposal. 1. Make sure the power button on the battery pack is in the off position. 2. Disconnect the cable from the power connector on the battery pack. 3.
4. Inside the enclosure, disconnect the two charging cables by separating each cable at the middle connector.
5. Place the enclosure on one side, and remove the two bracket screws from the bottom of the enclosure. To prevent the battery pack from shifting inside the enclosure while removing the bracket screws, support the pack with your hand. 6. Place the enclosure on the bottom, and carefully move the bracket towards the front of the enclosure. Avoid placing stress on the charging cables as you move the bracket.
7. Lift to remove the battery pack from the enclosure. 8. Place the new battery pack inside the enclosure. 9. Replace the bracket, and then the bracket screws removed in step 5. 10. Connect the charging cables disconnected in step 0. 11. Replace the lid on the enclosure, and insert and tighten the screws. 12. Plug the charging cable from the battery charger into the charger connector on the battery pack. Follow the steps on page 55 to charge the new battery pack.
Appendix A: Warranty See the Product Information Bulletin included with your shipment for the complete ETS-Lindgren warranty for your Model 4340 Digital Camera System (CCTV). DURATION OF WARRANTIES FOR MODEL 4340 CCTV All product warranties, except the warranty of title, and all remedies for warranty failures are limited to two years.
This page intentionally left blank.
Appendix B: EC Declaration of Conformity The EC Declaration of Conformity is the method by which ETS-Lindgren L.P. declares that the equipment listed on this document complies with the EMC Directive and Low Voltage Directive. Factory Issued by ETS-Lindgren L.P. 1301 Arrow Point Drive Cedar Park, TX, USA 78613 ETS-Lindgren L.P.
