Owner manual

1.63
1.63
11
25
19
20
21
27
18
6
15
9
2
7
22
24
23
10
12
16
1
14
17
8
5
3
13
SEE NOTE 1
SCREW MUST BOTTOM OUT INTO
ITEM 14, 2X
PART OF LINEAR SLIDE ASSY
SEE ASSY 110073
4
31
28
34
INSTALL ITEM 30 W/29 AT THIS LOCATION
1. DIMENSION IS FROM MOTORBASE COVER TOP TO COUPLING HUB TOP.
ITEM # QTY PART NUMBER DESCRIPTION
31 1 880301 INSERT,SPIDER,92 SHORE A
30 1 890687 CABLE CLAMP P-CLIP 1/4" PLASTIC(NOT SHOWN)
29 3 910159 SELF TAPPING SCREW PAN HEAD ZN6-32X3/8
28 1 110747 MOUNT,CHAIN,CABLE
27 3 110765 KNOB,HAND,ALUM,5/16 THRD,MODIFIED
26 1 105012 KEY, .187" X .875"
25 1 109980 PIN,LOCATING,MAST ASSY
24 10 910664 HEX NUT,STAINLESS 1/4-20
23 6 910393 WASHER,5/16,LOCK,STL,ZINC,SPLT
22 10 910762 LOCKWASHER,SPLIT,1/4:,SS
21 3 891020 ROD END,5/16-18 FULL THRD
20 3 890694 DOWEL PIN 1/4 X 1.0 SS
19 6 910777 SCREW,1/4-20 X 1,SH,CAP,SS
18 6
910437
SCREW SOCKET HEAD ALLEN 1/4-20 X 1/2
17 16 910136 SCREW ALLEN HEAD 8-32 X .5
16 2 910801 SCREW,8-32 X 7/8,SH,GR8
15 1 891016 SPRING,WAVE,3/8ID X 9/16OD X .715FL
14 1 109975 STOP,SHAFT
13 1 109979 SUPPORT,CHANNEL,MOTORBASE MOUNT
12 1 109977 SUPPORT,CHANNEL,BRAKE SIDE
11 1 109967 RING,MOUNT MAST ASSY
10 6 910386 BOLT,5/16-18 X 3/4,HEX,GR5
9 4 910447 BOLT,1/4-20 X 1,HEX,SS
8 6 910441 BOLT,1/4-20 X 3/4,HEX,SS
7 1 910931 SCREW,3/8-16 X 4 1/2,HEX,CAP,SS,FULL THRD
6 1 890912 KNOB,3/8 HEX BOLT
5 2 109978 MOUNT,BEARING,CHANNEL SUPPORT
4 1 880302 HUB,COUPLING,AL,7/8" BORE
3 1 109040 ASSY,MOTORBASE,2188
2 1 109984 CROSSPLATE,CHANNEL MOUNT
1 4 - PILLOW BLOCK & BEARING PART OF LINEAR SLIDE ASSY
MATERIAL
CHECKED
APPROVALS
1:2
109987
A
1
DECIMALS
UNLESS OTHERWISE SPECIFIED:
TOLERANCES ARE:
DIMENSIONS ARE IN INCHES
FINISH
X.XXX
X.XX
±
±
ANGLES
±
1
DRAWN
DOCUMENT, WHOLE OR IN PART,
PERMISSION OF ETS LINDGREN
WITHOUT EXPRESS WRITTEN
IS PROHIBITED.
ANY DUPLICATION OF THIS
PROPRIETARY INFORMATION
EMC Test Systems, L.P.
Cedar Park, TX
TITLE
RBG
DATE
Glendale Hts, IL
Lindgren-RF Enclosures
SEE BOM
DO NOT SCALE DRAWING
SHEET OF
.015
DWG. NO.
An ESCO Technologies Company
ETS LINDGREN
.005
.5
SIZE
D
SCALE
TM
REV.
REF DRAWING
NOTES:
ECO# REV APPROVEDDESCRIPTION DATE
REVISIONS
5068
A
RELEASED
3/23/06
RBG
NONE
7/7/05
ASSY,SLIDER,MAPS