User guide
Table Of Contents
- 1 Security recommendations
- 2 CERTIFICATE OF CONFORMITY
- 3 Products identification
- 4 Data-sheet
- 5 Product overview
- 1 Dimensions
- 2 Connectors
- 3 Led indicators
- 4 DIP switches
- 5 Factory default push-button
- 6 Mounting the product on a DIN rail or removing it
- 7 Cooling
- 8 RS232 interface
- 9 RS485 interface
- 10 Digital input and output
- 11 Connecting the antenna
- 12 Installing the SIM card
- Set up steps
- 2 Connecting a PC to the router for configuration
- 3 Rebooting the router after parameters changes
- 4 Recovering the factory LAN IP address
- 5 Recovering the factory configuration
- 6 Restricting access to the administration server
- 7 Recovering a free access to the administration server
- 8 Factory configuration
- 9 LAN interface set up
- 10 UMTS – GSM-GPRS-3GDGE interface set up
- 11 Setting up the DynDNS service
- 12 Creating VPN connections between routers
- 13 Routing functions
- 14 Address and port translation
- 15 VRRP redundancy
- 16 Remote users connections service
- 17 Remote users connections
- 18 M2Me_Connect service
- 19 Users list
- 20 Firewall
- 21 Serial to IP gateway
- 22 USB to IP gateway
- 23 Advanced functions
- 1 Diagnostic menu
- 2 Saving the configuration to a file
- 3 Updating the firmware
- Signets Word
SET UP
10 UMTS – GSM-GPRS-3GDGE interface set up
The RAS-3G router’s UMTS – GSM-GPRS-EDGE interface is configured through the WAN interface
menu :
The 3G modem interface is configured through the « Modem » page.
The PPP interface to the provider is configured through the « Connection » page.
The conditions at which the 3G connection can be reset is configured through the « Control » page.
Remark : Once that operations will have been carried out, check the Reception indicator
is
permanently ON. It signifies the RAS-3G is now connected to the UMTS network.
10.1 Modem menu
• Select the « Configuration» menu and then « WAN interface» and then “Connection”.
“APN” parameter
:
Enter the APN code assigned by the GSM operator.
”User name” & “password” parameters
:
Enter the user name and password assigned by the GSM operator.
Remark : If no user name or password have been assigned by the GSM operator, enter at least an
alphabetic character in each field.
10.2 Connection menu
• Select the « Configuration» menu and then « WAN interface» and then “Connection”.
“Obtain an IP address automatically” checkbox
:
Set that option if the provider assigns automatically an IP address to the router through the air
interface each time it connects to the 3G or GSM network.
Remark : In most cases, and in particular when the RAS-3G is connected to the Internet, that checkbox must be selected.
“IP address”
& “netmask” parameter :
Enter the fixed IP address and netmask assigned to the router if it not assigned through the air
interface.
“Obtain DNS IP addresses automatically” checkbox
: Select that checkbox if the Domain name
servers IP addresses are provided automatically through the air interface.
Remark : In most cases, and in particular when the RAS-3G is connected to the Internet, that checkbox must be selected.
“Primary DNS IP address”
& “secondary DNS IP address” parameters :
Enter the IP addresses of the domain name servers if they are not assigned through the air interface.
“Activate network address translation” checkbox :
If that option is selected, the source IP address of any frame coming from a device connected to the LAN interface and
routed to the WAN interface , is replaced by the router WAN IP address.
Remark : In most cases, and in particular when the RAS-3G is connected to the Internet, that checkbox must be selected.
”SMTP server” parameter
:
Enter the address of the SMTP server for outgoing mails (ex : smtp.nerim.net)
“Source account e-mail address” parameter
:
Enter the email address attached to the account.
Page 32 User guide ref 9020009-01 UMTS GPRS EDGE router ref. RAS-3G