Part # SC-20-840-SV-OS-BZ SC-20-840-SV-OS-W Model # 51402241 51402242 Use and Care Guide LED SECURITY LIGHT Dusk to Dawn Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday 1-855-ETi-SSLI (1-855-384-7754) www.ETiSSL.com THANK YOU We appreciate the trust and confidence you have placed in ETi through the purchase of this LED light. Visit us online to see our full line of products.
Table of Contents Hardware Included..................................4 Installation.................................................5 Maintenance..............................................7 Light Distribution.......................................7 PIR Sensor Testing.....................................8 Care & Cleaning.......................................11 Troubleshooting.......................................11 Table of Contents.......................................3 Safety Information............
Pre-Installation PLANNING INSTALLATION Before beginning assembly, installation, or operation of the product, make sure all parts are present. Compare parts with package contents list and hardware contents list above. If any part is missing or damaged, do not attempt to assemble, install, or operate the product. Contact Customer Service for replacement parts. This light fixture is suitable for wall mounting or eave mounting only. It is not suitable for ground mounting installation.
Installation WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker before removing the existing light fixture or installing the new one. With power disconnected to the electrical box, remove the existing fixture.
Installation (continued) the light fixture to 4 Attaching the mounting bracket AA □□ Install the light fixture base (B) to the mounting bracket (FF) using the long mounting screw (AA) provided, making sure no wires are visible outside the light fixture. □□ Insert the rubber plug (DD) into the hole on the light fixture base (B) for a finished appearance.
Maintenance To replace the photocell □□ Remove the rubber plug (DD) and long mounting screw (AA) from the light fixture base (B). □□ Unscrew the two wire connectors (EE) to disconnect the photocell (C). □□ Replace with a new photocell (Model # EP-120R or equivalent) using the same two wire connectors (EE). B C EE DD AA Light Distribution C0 / 180, 78.7 C30 / 210, 78.2 C60 / 240, 78.5 C90 / 270, 79.2 AVERAGE BEAM ANGLE (50%) : 78.7 DEG 7 ETiSSL.
PIR Sensor Testing 1 Lighting the product and preheat □□ When power is first applied, the light will turn on immediately. Waiting for 20 seconds to allow the sensor to warm up. 2 Test Mode □□ The motion sensor must be tested before setting the time and sensitivity levels. The TEST option is located on the TIMER control knob on the underside of the sensor head. To test the fixture, switch the wall switch that controls power to the fixture to the ON position and turn the rotary knob to the “TEST” area.
PIR Sensor Testing (continued) 4 1. Auto Mode Set-up □□ Once the fixture has been tested for proper operation and sensitivity, rotate the TIMER control knob past the “TEST” setting into the timer settings. The timer settings indicate how long the light stays on after the PIR senses motion. There is LED indicator inside 2. Auto Mode Operating □□ Rotate the TIMER control knob past the “TEST” setting into the timer settings.
PIR Sensor Testing (continued) 6 Troubleshooting □□ Extremely hot or cold weather could affect the performance of the built-in sensor that detect body heat. Certain winter clothing can shield a person’s body heat from the sensor during extremely cold weather. During extremely hot weather, the sensor may not be able to distinguish the difference between normal body temperature and the surrounding high temperature. The sensor will begin to work normally once weather conditions return to normal.
Care & Cleaning CAUTION: Before attempting to clean the fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from the fuse box. □□ Clean the fixture with a soft, dry cloth. □□ Do not use cleaners with chemicals, solvents, or harsh abrasives. Troubleshooting WARNING: Before doing any work on the fixture, disconnect power to the light fixture. Minor problems often can be fixed without the help of an electrician. Problem The fixture will not light.
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday 1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com Retain this manual for future use.
