aternit hot water solutions by CHRIMSIEN EXTERNAL GAS HOT WATER UNIT INSTALLATION AND OPERATING INSTRUCTIONS MODELS G16/G20/G26 FOR ADVICE, REPAIRS AND FAST SERVICE 1300 367 565 20501072(K)
INDEX INSTALLATION INSTRUCTIONS PAGE NO.
INTRODUCTION ETERNITY G16/G20/G26 INSTALLATION INSTRUCTIONS INTRODUCTION The E I ERNTTY 16/20/26 is an external electronic gas hot water heater. The ETERNITY 16/20/26 is supplied set at a constant 60°C outlet temperature depending on the model purchased. Three optional remote controls can be provided for complete hot water temperature selection and if this option is used an approved temperature limiting device must be installed. THIS HOT WATER UNIT IS NOT FOR POOL OR SPA HEATING GENERAL 1.0.
DIMENSIONS CONNECTIONS Model : 16/20 COLD WATER INLET RP1/2/15 WATER INLET FILTER CABLE ENTRY POINT HOT WATER OUTLET 111M=1==All RP1/2/15 PIFQ) GAS SUPPLY INLET RP3/4/20 PRESSURE RELIEF VALVE 330 Model : 26 12 165 15 COLD WATER INLET RP3/4/20 WATER INLET FILTER CABLE ENTRY POINT HOT WATER OUTLET 10111===YAN RP3/4/20 [ GAS SUPPLY INLET RP3/4/20 pi= Cr 25: PRESSURE RELIEF VALVE 330 2
EXPLODED DIAGRAM Model : 16/20 NOS. PARTS DESCRIPTION 1 FLUE OUTLET 2 GAS VALVE 3 CIRCUIT BOARD 4 BURNER CASE 5 HOT WATER OUTLET 6 COLD WATER INLET 7 GAS SUPPLY INLET 8 HEAT EXCHANGER Model : 26 0 a I U 0 0 III J / NOS.
TECHNICAL DATA 1.1 TECHNICAL DATA AND DIMENSIONS ETERNITY 16 / 20 / 26 Nominal hourly gas consumption MJ/h by proportional electronic gas control MODEL 16 20 26 125 160 200 MJ/h Test point pressure MODEL NG LP .40 .40 16 .56 .61 20 26 .68 .70 MODEL 16 20 26 ML/M 10 12.5 16.25 Water heating capacity raised 40°C Max 1200kPa Working pressure MODEL NG LPG MODEL NG LPG 16/20 1.35 1.35 mm 26 1.34 1.0mm 1.65 1.2 mm 1.65 1.
TECHNICAL DATA 1.4 1.5 HEATER DIMENSIONS: DEPTH WIDTH HEIGHT 165mm 350mm 575mm WARNING LABELS Located on the side of the cabinet. PLEASE READ THESE LABELS CAREFULLY. 1.6 INSTALLATION POSITION THIS HEATER IS APPROVED FOR OUTDOOR INSTALLATION ONLY-IT IS NOT SUITABLE FOR INDOOR USE. Refer AS5601 for clearance details for flue terminal. In addition,ensure that the appliance installation position permits easy access for maintenance and operation.
GAS CONNECTION 1.8 GAS CONNECTION (1) Fit a union to the water heater gas inlet for easy connection and removal. The thread diameter is 18mm. THIS DOES NOT INDICATE THE SIZE OF THE GAS SUPPLY refer to AS5601 for guidance on pipe sizing. (2) Fit an AGA approved isolating gas cock in the supply line adjacent to the water heater gas connection.
COLD WATER CONNECTION 1.9 COLD WATER SUPPLY TO WATER HEATER Refer to the Technical Sheet for the position of connections. Minimum of 13mm for model 16/20 and 18mm for model 26 copper tube should be connected to the appliance . The WATER INLET connection are 13mm BSP for model 16/20 and 18mm BSP for model 26 and requires a union to allow for removal of the water heater. Pipe sizing from the cold water supply should be sized according to local BY LAWS for water supply.
HOT WATER CONNECTION 2.0 Refer to Technical Sheet for the position of connection. The outlet connection is 13mm for model 16/20 and 18mm for model 26 male thread and requires an isolating union to allow for removal of the unit. 2.1 Install the hot water supply line to the unit in a minimum of 13mm for model 16/20 and 18mm for model 26 copper tube. for units set at 50°C this must be a minimum of Four (4) Metres to the first outlet. 2.
REMOTE CONTROLS Refer to Technical Sheets 4.0 The ETERNITY 16/20/26 comes complete, with one, two or three remote control panels, as optional extras. ONE REMOTE CONTROLS SYSTEM TWO OR THREE REMOTE CONTROLS SYSTEM MODEL MODEL MODEL MODEL CMR-154 CMR-154 YST-84 YST-84S MAIN CONTROLS MAIN CONTROLS SHOWER CONTROLS ENSUITE CONTROLS 4.
1 REMOTE CONTROLS WIRING DIAGRAM WIRING DIAGRAM OF PCB TURN OFF POWER SUPPLY TO HOT WATER UNIT AND REMOVE PLUG FROM POWER OUTLET BEFORE REMOVING FRONT COVER OF HOT WATER UNIT. ORO.
MAIN REMOTE CONTROLS MAIN REMOTE CONTROL CMR-154 16 f 7 \ ( 4 5 AL M • 17 1' 1 17 17 t PMCILI•ULD rr 4-1 Fi-1 j 3 2 1 . U6FF i( :.:.. ... t. . .1 8 ON (I) AM :o .....°: ? KITCHEN CMR- 154 TIME SET I 9 1a to el° dlArrEtrnott mtealuttatettretcoarigit.*: hat. artdb.mst t, onvittnet.tere,pkatekter 0.
SHOWER/SUB REMOTE CONTROLS SHOWER / SUB REMOTE CONTROLS YST-84 /YST-84S 16 7 C [ 3-A 3 ALM (.„ LA •nrit rf TI PM Li LI • LI 11 Pt 1 AM . . . r--- Ell In 3-B 2 , TRANSFE1 11 4 5 nn ILM , f: - --°11 BATHROOM YST-84 ON/OFF o.... O.:': Fa sa-ery erd pew usg Ice areto rend te.e.e. Arremox 11.02.Mry cacd,,,:edetrk,i, PM,. *arr. xla (ILLUSTRATION IS FOR YST-84) NOS.
MOUNTING REMOTE CONTROLS MOUNTING AND WIRING OF REMOTE CONTROLS 4.7 REMOTE CONTROLS OPEN THE CARTON BOX AND MAKE SURE TO CHECK FOLLOWING PARTS PROVIDED. • MAIN CONTROLS MODEL CMR-154 j------------,,,--\--,_____ V 01" 2PCS REMOTE CONTROLS 2PCS WOOD SCREW CURL PLUG WIRING • SHOWER/SUB CONTROLS MODEL YST-84 / YST-84S -.
ALTERNATIVES IN MOUNTING REMOTE CONTROLS IN EITHER OF THE FOLLOWING TWO ALTERNATIVES, YOU ARE TO REMOVE METAL BRACKET ATTACHED TO THE BACK OF EACH REMOTE BY SLIDING THE BRACKET FIRMLY DOWN TILL IT IS RELEASED FROM THE NOTCH BY CLICK, THEN PULL IT OUT.(MAIN CONTROL ONLY) SINCE SHOWER/SUB CONTROLS WATERPROOFED, PLEASE INSTALL ON DIRECT MOUNTING. A. USING THE BRACKET (BEING REMOVED AS ABOVE) AS A FIXTURE: (REFER THE DIAGRAM BELOW) 1.
USER INSTRUCTIONS USER INSTRUCTIONS PLEASE HAND THIS HANDBOOK TO THE USER AFTER INSTALLATION. INTRODUCTION: You have selected the ETERNITY electronic gas hot water unit. The following instructions will assist you to obtain the best performance from your ETERNITY unit. OPERATION: Up to three remote controls are able to be installed with your ETERNITY unit for complete controls of your hot water. Please note units without remote control will be set at 60°C or in the case of commercial units 75°C.
USER INSTRUCTIONS OPERATION OF SHOWER / SUB REMOTE CONTROLS The SHOWER/SUB CONTROLS overrides the operation of the main control. Leave the operation switch on the MAIN CONTROL switched ON. YST-84/84S SHOWER/SUB CONTROLS 1. Press the ON/OFF button after opening the cover on the CONTROLS. See diagram 1 below. 2. Press the TRANSFER BUTTON and the TRANSFER light will illuminate and the TEMPERATURE DISPLAY will have 42°C displayed. Please refer to page 12 of this handbook. See diagram 2 below. 3.
HINTS FOR USING REMOTE CONTROLS FOR SAFETY AND ENERGY SAVINGS 1. Set the MAIN CONTROL to 42°C for normal household use and to prevent small children from scalding. 2. For the dishwasher set the MAIN CONTROL to 60°C or the temperature in the manufacturer's instructions. 3. For showering use settings between 37°C-39°C and no cold water will be needed to be mixed, and if other hot or cold water taps are used the temperature will be maintained.
CARE OF THE ETERNITY UNIT 1. DO NOT HANG WASHING OR OTHER MATERIALS ADJACENT TO THE UNIT. 2. DO NOT STORE INFLAMMABLE MATERIALS WITHIN 2 METERS OF THE UNIT. 3. DO NOT TOUCH THE FLUE OUTLET OF THE UNIT DURING OR IMMEDIATELY AFTER OPERATION. 4. IF ANY GAS SMELL COMES FROM THE UNIT, DO NOT USE NAKED FLAMES TO TEST FOR GAS LEAKS. 5. TURN OFF THE GAS SUPPLY AND POWER AND CONTACT YOUR GAS SUPPLY COMPANY. 6.
HINTS FOR USING THE ETERNITY UNIT POINTS NEEDED FOR YOUR SPECIAL ATTENTION ,L Danger NO INSTALLATION INDOORS (May cause oxygen deficiency accident or incomplete combustion.) The unit is outdoor installation type. Never install indoor or in the bathroom. It will be extremely dangerous since it will cause oxygen deficiency and incomplete combustion. Prohibited ,AWarning WATCH FOR GAS LEAK May cause fire.
Warning CAUTION FOR INFLAMMABLE ITEMS (May cause fire or explosion.) NO DISASSEMBLY, REPAIR OR MODIFICATION (May cause fire, electric shock or other accidents.) 414 O O L Warning 4.1() C== No Disassemble O r 0,3 CJ Do not place any inflammable items such as gasoline or benzene nor use them around the unit.Take special care. Do not dissemble or modify the units.
Warning CAUTION TO PREVENT SCALDING Caution Check the water temperature by hand first before using shower. MEASURE TO BE TAKEN IN CASE OF EMERGENCY When there is an emergency such as earthquake or fire, apply following procedure. 1. Close the hot water outlet. 2. Close the gas valve and the main water valve. Close Close 3. Turn off the main power. However, in case of gas leakage, first close the gas valve then wait for the leaked gas to disperse then turn off the main power supply. 4.
Caution DANGER OF WET HANDS INSERT POWER PLUG PROPERLY INTO TERMINAL (May cause electric shock.) 4• Warning Check Do not touch power plug with wet hands. It is dangerous, because it can cause electric shock. Check the power plug for dust accumulation, then properly insert to the power point. DO NOT PULL POWER CORD DO NOT USE POWER CORD BUNDLED (May generate heat and cause fire.) (May generate heat and cause fire.) Prohibited Prohibited Never use power cord in a bundled condition.
Caution CONFIRM IGNITION, COMBUSTION AND EXTINCTION Check ON v ° 11_4_11 ON/Ofj A J 'TRANSFER Please always check ignition, combustion and extinction of the unit by the operation lamp of the main or shower/sub remote controls. DO NOT PUT WATER ON THE REMOTE CONTROLS DO NOT INSTALL NEAR ELECTRIC APPLIANCES (May cause failure.) Check Do not put water on the remote controls. It will cause failure. When installed near to TV or radio, it may cause picture disturbance or sound disturbance.
FAULT MONITOR FAULT MONITOR THE ETERNITY HOT WATER UNIT HAS A SELF DIAGNOSING FUNCTION FOR FAULTS. When the unit does not operate correctly, an error code is displayed on the MAIN and SHOWER remote controls TEMPERATURE DISPLAY INDICATOR. The cause of the fault can be determined after checking the fault numbers display on the remote control display. PROBLEM REMEDY 11 GAS BURNER FAILS TO IGNITE. CHECK GAS SUPPLY. 72 FALSE FLAME DETECTION. CALL SERVICE CENTRE. 12 LOSS OF COMBUSTION.
WARRANTY CONDITIONS Eternity Continuous Flow 1. All Eternity water heaters must be installed by a Licensed installer. 2. Only Authorised personnel must Install, Commission or Service Eternity water heaters. 3. All Eternity water heaters must be installed in accordance with Manufacturer's Installation Instructions and in Accordance with local regulations, municipal building codes and current AS/NZS3000, AS/NZS3500, AS 3498 and AS5601. 4.
Warranty Terms Eternity Water Heaters are covered by Eternity for any cost of labour and parts in the event of a component failure due to any defects that may arise either from workmanship and or faulty material. The Warranty commences on the date of Installation: Domestic Appliance Heat Exchanger Eternity Product Parts 10 Years Labour 3 Years .
