CE User Manual Production Dates: September 2004 - Present C o p y r i g h t © 2 0 0 8 E le c tr o n i c T h e a t r e C o n t r o l s , I n c . All Rights reserved. P r o d u c t in f o r m a t i on a n d s p e c i f i c a t i o n s s u bj e c t t o c h a n g e . P a r t N u m b e r : 7061M1260-06.
Table of Contents Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Source Four PARNel CE guidelines. . . . . . . . . . . . . . . . . . . . . . . . . .2 Basic assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Luminaire information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Colour frame holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Replacing the HPL lamp . . . . . . .
English Declaration of conformity We, Electronic Theatre Controls, Europe Ltd.
English Source Four PARNel CE guidelines The Source Four PARNel CE is intended for professional use only. Read the entire User Guide before using equipment. WARNING: • • • • • • • • • • • • • • Please note the following safety precautions. Do not mount the Source Four PARNel CE on or near a flammable surface. Use the Source Four PARNel CE in dry locations only, where humidity does not exceed 90 percent. The luminaire is for indoor use only and is not intended for outdoor use.
English Basic assembly Yoke Yoke locking knob Lamp housing Gel retaining clip Color frame holder ING! WARN Lens catcher Clear lens Stippled lens Tabs Lens rotating ring Focus knob Color frame Safety screen Figure 1 Luminaire information WARNING: Please note the following safety warnings before use: Do not mount the luminaire on or near combustible surfaces. Do not operate the luminaire without a lens installed. Always hang the luminaire with the color frame retaining clip in the locked position.
English HPL lamp table CAUTION: Do not use lamps other than the HPL in Source Four fixtures. Use of lamps other than HPL will void your warranty. Lamp code Watts Volts Initial Lumen Note: Colour temp.
English Colour frame holder Retaining clip in the locked position Figure 2 The colour frame holder is equipped with a spring-loaded retaining clip that prevents colour frames and accessories from falling out. See Figure 2. WARNING: Make sure all colour frame accessories are locked in position with the retaining clip before hanging the Source Four PARNel CE. Step 1: Release the retaining clip by pushing it sideways while gently pulling backwards. Step 2: Insert the colour frame.
English Step 3: Holding by the base, remove the HPL lamp from its box. CAUTION: Use caution when installing or replacing any lamp. When installing/replacing lamp, be sure to point the lamp away from your face and away from others before inserting it firmly into the assembly. This may prevent injuries if the lamp should break. CORRECT INCORRECT Note: To avoid premature lamp failure, do not touch the lamp glass. If you do, clean it carefully with isopropyl alcohol and a clean lint-free cloth.
English Lens identification Lenses for the Source Four PARNel come in two versions. The wave/clear lens is in a fixed position in the rear of the luminaire. The wave/stippled lens is in the rotating ring at the front of the luminaire. The wave surfaces face each other. Wave/Stippled Lens (WS) Wave/Clear Lens (WC) Figure 5 Changing front lens Replace lens if it becomes cracked or badly scratched. CAUTION: Never operate the luminaire without a lens in place.
English Step 5: Gently push the top of the lens inward until it snaps behind the spring clip. Spring clip Retaining clip Retaining clip Lens Spring clip Focus knob Tab Figure 6 Lens catcher Figure 8 Figure 7 Positioning the wave/stippled front lens. Top center notch Bottom two center notches Figure 9 Step 1: There are seven notches cut into the stippled side of the lens. Position the lens so the cluster of three notches is on top.
English Portable appliance test (PAT) guidelines The Portable Appliance Test is a set of tests that must be administered to electrical equipment in the UK and some locations in Europe to ensure safety.The tests are typically carried out using a small PAT device. The PAT device connects to a power source and then attaches to the product via an electrical outlet and test probes. The PAT provides a simple pass or fail result, allowing rapid testing of large inventories.
Corporate Headquarters 3031 Pleasant View Road, P.O.
