CE User Manual Production Dates: September 2004 - Present C o p y r i g h t © 2 0 0 8 E le c tr o n i c T h e a t r e C o n t r o l s , I n c . All Rights reserved. P r o d u c t in f o r m a t i on a n d s p e c i f i c a t i o n s s u bj e c t t o c h a n g e . P a r t N u m b e r : 7061M1210-06.
Table of Contents Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Source Four PAR CE guidelines . . . . . . . . . . . . . . . . . . . . . . . . .2 Basic Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Luminaire information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Colour frame holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Replacing the HPL lamp . . . . . . . . . . . . . . .
English Declaration of conformity We, Electronic Theatre Controls, Europe Ltd.
English Source Four PAR CE guidelines The Source Four PAR CE is intended for professional use only. Read the entire User Guide before using equipment. WARNING: • • • • • • • • • • • • • • Please note the following safety precautions. Do not mount the Source Four PAR CE on or near a flammable surface. Use the Source Four PAR CE in dry locations only, where humidity does not exceed 90 percent. The luminaire is for indoor use only and is not intended for outdoor use.
English Basic Assembly Earth continuity cable Yoke Yoke locking knob Gel retaining clip Lamp housing Colour frame holder ING! WARN Lens catcher Tabs Lens Colour frame Lens rotating ring Safety screen Figure 1 WARNING: Please note the following safety warnings before use: Do not mount the luminaire on or near combustible surfaces. Do not operate the luminaire without a lens installed. Always hang the luminaire with the color frame retaining clip in the locked position.
English HPL lamp table WARNING: Do not use lamps other than the HPL in Source Four PAR CE luminaries. Use of lamps other than HPL will void your warranty. Lamp code Watts Volts Initial Lumen Colour temp.
English Replacing the HPL lamp Lamp retention brackets Knurled bolt HPL lamp Lamp housing Figure 3 A lamp must be installed before you use the luminaire. Note: Verify that the HPL lamp you intend to install is suitable for your facility’s voltage; 115-, 120-, 230-, and 240-volt HPL lamps are available. See HPL lamp table, page 4. Operating HPL lamps above their rated voltage reduces lamp life and can cause premature lamp failure. WARNING: Let the lamp cool before replacing.
English Step 7: Reinstall the Earth continuity cable, then install the lamp housing by aligning the bolt hole and tightening the knurled bolt. Lens identification Lenses for the Source Four PAR come in four versions. The type, or beam spread, can be identified by the lens texture.
English Step 2: Hold the lens by the edge and position it so the convex side faces the rear of the luminaire. Note: Installing the lens with the convex side out will not impair the optics, but it will make removing the lens difficult. Step 3: From the top of the luminaire, slide the lens behind the lens catchers and position it behind the tabs on the bottom of the lens rotator ring. Step 4: Gently push the top of the lens inward until it snaps behind the spring clip.
English Portable appliance test (PAT) The Portable Appliance Test is a set of tests that must be administered to electrical equipment in the UK and some locations in Europe to ensure safety.The tests are typically carried out using a small PAT device. The PAT device connects to a power source and then attaches to the product via an electrical outlet and test probes. The PAT provides a simple pass or fail result, allowing rapid testing of large inventories.
English 9
Corporate Headquarters 3031 Pleasant View Road, P.O.
