User Guide

ManualsBrandsETC ManualsLED LuminaireETC 7419A1001-XX Desire Fresnel Lustr X8 LED Luminaire

Table Of Contents

ETC Quick Guide

Desire Fresnel

Corporate Headquarters n Middleton, WI, USA | +1 608 831 4116

New York, NY | Orlando, FL | Los Angeles, CA | Austin, TX

Web

etcconnect.com | Support support.etcconnect.com | Contact etcconnect.com/contactETC

Product information and specifications subject to change. ETCintends this document to be provided in its entirety.

7419M1300-1.1.2 Rev A Released 2022-05

Overview

Use the images below as a guide to connect power and data and to navigate the basic features

of the fixture. For complete information, download the

Desire Fresnel User Manual

etcconnect.com, or view online help on your smartphone or tablet by scanning this code.

Accessory holder:

Insert accessories into the two available slots from either side of the holder, and

then lock the holder. See

Add Accessories on page4

Yoke tilt-lock:

Tilt the fixture as needed, and then turn the tilt-lock clockwise to lock the position. If

necessary, pull the tilt-lock away from the stem to adjust the tilt-lock position.

Adjustable yoke:

Loosen the bolts, and then shift the adjustable yoke forward or backward as

needed to balance the fixture. Tighten the bolts to secure. See

Add Accessories on page4

Zoom knob:

Rotate the zoom knob on either side of the fixture to adjust from spot to flood.

NFC(Near Field Communication) tag: Use the

Set Light

app to wirelessly configure the fixture,

with or without power applied to the fixture.

User interface:

View the fixture status, set the DMXaddress and mode, or set stand-alone options.

Antenna: For use when controlling the fixture using wireless DMX.

Safety cable attachment point:

See

Mounting and Safety Cables on page4

DMX In and DMX Thru connectors:

Five-pin XLRconnectors for DMX/RDM in and thru.

Power In and Power Thru connectors:

powerCON

TRUE1 TOP connectors for power in and thru.

Summary of content (8 pages)

PAGE 1
ETC Quick Guide Desire Fresnel Overview Use the images below as a guide to connect power and data and to navigate the basic features of the fixture. For complete information, download the Desire Fresnel User Manual at etcconnect.com, or view online help on your smartphone or tablet by scanning this code. A H G B F E C A D D I J A Accessory holder: Insert accessories into the two available slots from either side of the holder, and then lock the holder. See Add Accessories on page 4 .
PAGE 2
ETC Quick Guide Desire Fresnel User Interface G A DMX DMX F Address 001 Mode 3 Ch RGB B DMX Loss HLL 2 Min C 1/3 Red D E A Display: The colors of options on the display correspond to the colors of the encoders below the display ( E ) and the Intensity encoder to the right of the display ( B ). B Intensity encoder: • When in DMX mode, press the Intensity encoder to enter Focus mode when focusing the fixture.
PAGE 3
ETC Quick Guide Desire Fresnel Safety WARNING: RISK OF ELECTRIC SHOCK! The light source in this luminaire is not user-replaceable, and must be replaced only by a qualified technician. Contact ETC Customer Support for assistance. AVERTISSEMENT : RISQUE DE DÉCHARGE ÉLÉCTRIQUE! La source lumineuse de ce projecteur n'est pas remplaçable par l'utilisateur et ne doit être remplacée seulement par un technicien qualifié. Contactez le service client ETC pour obtenir de l’assistance.
PAGE 4
ETC Quick Guide Desire Fresnel AVERTISSEMENT : Prendre connaissance des avertissements de sécurité suivants avant toute utilisation : • Débranchez le projecteur de son alimentation et du DMX et laissez-le refroidir avant d’installer des accessoires ou d’effectuer un nettoyage ou un entretien. • N’utilisez que de la quincaillerie de montage adaptée au poids total des projecteurs et des accessoires. • Lorsque le luminaire est accroché, l'axe entre les points de fixation de la lyre doit être parallèle au sol.
PAGE 5
ETC Quick Guide Desire Fresnel Connect Power and Data 1. 2. 3. 4. Attach five-pin XLR cable to the DMX In connector (if using external control). Plug the XLR cable (if using) into the DMX source or data daisy-chain. Use the DMX Thru connectors to connect up to 32 device loads on the DMX daisy chain. Use the Power Thru connectors to connect other fixtures using the following recommended guidelines.
PAGE 6
ETC Quick Guide Desire Fresnel Use Fixture in DMX Mode After you connect power and data to the fixture and provide DMX, press the Function button ( ), use the Intensity encoder to navigate to DMX Mode, and then press the Intensity encoder to select it. In the DMX screen, you can set the DMX address, DMX mode, and DMX loss behavior. The DMX screen displays the current DMX values. Press any of the encoders to "wake" the display, and then press any of the encoders to edit the values.
PAGE 7
ETC Quick Guide Desire Fresnel Use Fixture in Stand-alone Mode After you connect power to the fixture, press the Function button ( ), use the Intensity encoder to navigate to one of the following stand-alone modes, and then press the Intensity encoder to select it: • • • • Studio: Use one of three studio (white light) presets, or customize the presets. Color: Use one of 12 color presets, or customize the presets. Effects: Use a sequence, or customize a sequence.
PAGE 8
ETC Quick Guide Desire Fresnel More Options • • • • Turn off the color: Press the Intensity encoder to toggle the intensity value from the current value to 0. Press the Intensity encoder again to toggle back to the previous intensity value. Revert to the original color of a preset: Press the encoder that corresponds to the preset again to restore the original values. Save the color to a preset: Press and hold the encoder that corresponds to the preset that you want to re-record.