Power Conditioner & Distribution Unit Owner's Manual

– 6 – ETAsys.com
Specifications are subject to change without notice.
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: [phone] • Fax: [phone]
FRONT PANEL FEATURES
1. Un-switched AC Outlet–The120VACoutletisalwayslivewhentheETA-S15LpowercordispluggedintoanACmainspower
sourceandvoltageispresent.Note:TheACmainspowerswitchdoesnotaffecttheUnswitchedACOutlet.TheUnswitched
Outlet is protected by the surge protection circuitry.
2. AC Mains Breaker–The15AratedbreakerwillopenifthecombineddrawofallACoutletsexceeds15A.Note:Thebreakeris
designedtoexceeditsratingforashortperiodoftime.Ifthebreakeristripped,youmustfirstremovetheloadfromtheETA-S15L
and then push to reset.
3. Power Switch –ToturntheETA-S15Lonoroff,presstheswitchtotheONorOFFposition.
4. Pull Out Light –TheLEDlightisdesignedtobepulledoutwhenneeded.
5. Pull Out Light Dimmer Switch –UsethiscontrolforthePullOutLight.Settingsincludean“Off”positionandtwobrightnesssettings,
LowandHigh,when“On.”
6. Power ON LED – Will illuminate blue when the AC Mains Power Switch is in the ON Position.
7. AC Fault Indicator – Although the Clamping Suppression circuit virtually assures protection from most transient voltage spikes and
surges, nature has a way of occasionally creating electrical forces that are beyond the capabilities of any device to absorb without
somedegreeofdamage.Intherareinstancethatthisoccursandthecircuithasbeendamaged,theRed“ACFault”LEDindicator
willilluminateandaninternalbuzzerwillsound.TheETA-S15Lwillalsoshutoffpermanentlyuntiltheunitisrepaired.Beadvisedthat
activationofthisfaultconditionandtheassociatedrepairisnotcoveredunderwarranty.NOTE:IftheACFaultLEDisilluminatingitis
importanttohaveallequipmentthatwasconnectedtothatACMainsLinebeinspectedforproperoperation.
REAR PANEL FEATURES
1. AC Mains Input – Connectthe9'(3m)powercordtoa15A120VACoutlettoprovidepowertotheETA-S15L.
2. AC Power Outlets – Theseeightoutletsare“Live”whenthefrontpanelpowerswitchisactivated.
3. XLR Light Socket – A12VDCXLRlightsocketprovidespowerfortheoptional,AtlasPower,AP-GNL18light.
4. Light Socket Power Switch – ThisswitchturnstheXLRlightsocketON/OFF.
INSTALLATION
Beforeinstalling,westronglysuggestyoureadtheentiremanualtoensureyoubenefitfromallthefeaturesoftheETA-S15L.The
ETA-S15Lcanbeplacedonashelforrackmountedinastandard19"widthrack.Whenrackmounted,placementwithintherackis
flexiblehowevertheETA-S15Lshouldbewithin6'ofadedicated15AACoutlet.Whenrackmounting,useRackRailtypescrews
which are
10
⁄32"x1".Alwaysmakesurethe15AoutletisproperlyinspectedbyacertifiedelectricianpriortoconnectingtheETA-S15L.
MakesuretoinspecttheequipmentthatistobepluggedintotheETA-S15Ltoensureitdoesnotexceed15Atotalamperagedraw.
ETA-S15L
Power Conditioner & Distribution Unit
1 2 345 6 7
1 4 32 2