Instruction Manual

Box Lock Hole
State Indicator
Thread Hole
3. Installation
Backup Battery Control Panel
Air Switch
Panel Box Appearance
Panel Box Insaid
Get the Panel off the track
Heat
2. Components
Thread holes
Screws
1. Cautions
4. LED Indicators and Wire Illustration
inB I O 16 0 I nstallation and C onnection G uide
1) Meaning of LED indicators:
LINK indicator (green): Constant light always indicates TCP/IP communication is normal.
ACT indicator (yellow): Flashing indicates data is transmitting through TCP/IP communication.
EXT RS485 indicator (yellow&green): Flashing indicates it is sending or receiving data through RS485 communication.
PC RS485 indicator (yellow&green): Flashing indicates it is sending or receiving data through RS485 communication.
POWER indicator (red): Light always indicates the control panel is power on.
RUN indicator (green): Flashing indicates that system is working normally.
CARD indicator (yellow): Flashing indicates a card is punched on reader.
2) Recommended use of wires：
3) The auxiliary input may be connected to infrared body detectors, alarm switches, etc.
4 The auxiliary output may be connected to door bells, alarms, etc.)
5) State Indicators are connected to the panel box, that is power indicator, run status indicator and communication status indicator.
Power Supply
Temper Switch
After the following installation, fix the panel to the track first, and then install other components .
Dissipation Hole
Control Panel
Control Panel
Panel Track
Panel Track
2
2
1
1
3) Install other components
2) Fix the box
1) Get through the thread hole
Inte rfac e Wir e Specification Network cable M aximum length
Power (A) 18AWG*2PIN / 1.5M
Wiegand (B)
24AWG*6PIN
(6PIN, 8PIN, 10PIN for different
readers)
CAT-5 or above network cable, one
way DC impeda nce is less than 100Ω
/KM
100M
Electric Lock (C)
18AWG*2PIN+24AWG*2PIN,
18AWG*2PIN for lock connection,
24AWG*2PIN for door sensor
connection.
/ 50M
Button (D) 24AWG*2PIN / 100M
EXT485 (E)
20AWG*2PIN+24AWG*2PIN,
20AWG*2PIN for reader power
supply, 24AWG*2PIN for RS485
communication
CAT-5 or above network cable, one
way DC impedance less than 100 Ω
/KM. In wire connection, +12V and
GND of power supply need to be
parallel and use double wires.
Share power with control panel: 100M
Use independence power supply
(connect RS485 signal interface only):
1000M
Please note th e fo llo win g cautio ns. Mis -opera tio n may le ad to pers onal in ju ry or
equip ment fa ilu re:
1）Do not energize the syste m befo re in sta lla tio n is complete ; never carr y out
insta lla tio n activ itie s when th e syste m is energiz ed.
2）All perip hera l devic es must be gro unded.
3）The conduits of wire s under re lay must be matched with metale d conduits , other wire s
can use PVC conduits .
4）It is stro ngly re commended th at th e length of exposed part of any connectio n cable
should not be lo nger th an 4 m
m. Pro fessio nal clampin g to ols may be used to avoid
unin tentio nal contact of exposed wire s to avoid short- circ uit or communic atio n failu re .
5）It is re commended th at card readers and butto ns be installe d at heig ht of 1.4m-1 .5m
above gro und.
6）It is re commended to use th e power supply fo r contro l panel, and exte rn al power
supply fo r each lock.
7）The applia nce shall be insta lle d and wire d in accordance with natio nal ele ctric al
code and by qualifie d pers onnel only
Descr iptio n of nor mal wor kin g s
ta te:
Connect the syste m to the power supply. If th e syste m work s pro perly, the POWER
indic ato r (red) is lit consta ntly and the RUN indic ato r (green) fla shes.
V alve r egulated lea d-ac id battery :
Constan t volt ag e charge volt ag e reg ulati on
Cycle use : 14.5V ~14.9V (25 )
Initial curren t: less tha n 2.88 A
Stan dby use: 13.6V ~13.8V (25 )
Capacity: 12V, 7.2A h/20 hr
Battery Type: LC-R A127R2T1
C aution :
Do not ch arge in a gas tight co ntaine r.
Do not sh ort the battery term inals.
Do not inc ine rate
Flush with water at once if co ntact is mad e with
elec trolyte (A cid )
Do not attem pt to disasse mble the battery .