SERVICE MANUAL SERVICE MANUAL
CREDITS/COPYRIGHT © 1996–99, 2001 Best Lock Corporation. All rights reserved. Printed in the United States of America. Information in this document is subject to change without notice and does not represent a commitment on the part of Best Lock Corporation. The software described in this document are furnished under a license agreement or nondisclosure agreement. This publication is intended to be an accurate description and set of instructions pertaining to its subject matter.
CONTENTS FIGURES V GETTING STARTED Introduction 1–7 1–7 Certifications and standards 1–7 HV and KV Locks 1–7 V Series Controller 1–8 Documentation package 1–8 Technical support 1–9 Support services 1–9 Telephone technical support Training seminars 1–10 SECURITY DEVICE MAINTENANCE 1–9 2–1 8KV/9KV magnetic stripe trim exploded diagram 2–2 8KV/9KV magnetic stripe trim parts list 2–3 8KV/9KV keypad trim exploded diagram 2–4 8KV/9KV keypad trim parts list 2–5 8KV/9KV proximity trim exploded diagram 2–6
Contents 34/35HV proximity trim exploded diagram 2–16 34/35HV proximity trim parts list 2–17 34/35HV case with deadbolt exploded diagram 2–19 34/35HV case with deadbolt parts list 2–20 34/35HV case without deadbolt exploded diagram 2–21 34/35HV case without deadbolt parts list 2–22 XV Controller exploded diagram 2–23 XV Controller parts list 2–23 External communications exploded diagram 2–24 External communications parts list 2–24 Programming parts diagram 2–25 Programming parts list 2–25 Card encoder parts
Contents Alarm troubleshooting GLOSSARY 3–11 A–1 SECURITY DEVICE HISTORY EVENT TYPES INSTALLATION INSTRUCTIONS INDEX V Series Service Manual B–1 C–1 D–1 iii
Contents iv V Series Service Manual
FIGURES SECURITY DEVICE MAINTENANCE 8KV/9KV magnetic stripe trim exploded diagram 8KV, 9KV keypad trim exploded diagram 2–4 8KV/9KV proximity trim exploded diagram 8KV/9KV chassis exploded diagram 2–2 2–6 2–8 34/35HV magnetic stripe trim exploded diagram 34/35HV keypad trim exploded diagram 2–10 2–13 34/35HV proximity trim exploded diagram 2–16 34/35HV case with deadbolt exploded diagram 2–19 34/35HV case without deadbolt exploded diagram XV controller exploded diagram 2–23 External communic
Figures TROUBLESHOOTING Enabling communications using the DIP switches 3–2 Connecting the palmtop cable to the base of the lock vi 3–3 V Series Service Manual
1 GETTING STARTED INTRODUCTION The V Series Service Manual contains essential information to help you maintain your 8KV, 9KV, 30HV stand-alone locks, and the XV Controller. CERTIFICATIONS AND STANDARDS HV and KV Locks ■ ■ ■ V Series Service Manual The strike fits the standard door frame cutout as specified in ANSI A115.1. The faceplate dimensions fit the standard door preparation as specified in ANSI A115.1.
Getting Started V Series Controller The controller complies with the following: ■ ■ ■ ■ ■ ■ ■ FCC CFR 47 Part 15, Subpart C for Intentional Radiators CES–003 Canadian EMI Requirements IEC 61000–4–2 (1995) ESD Immunity IEC 61000–4–3 (1995) RD Immunity IEC 61000–4–4 (1995) EFT Immunity International Safe Transit Association–Procedure 1A Humidity Test RTCA/DO–160C–Extended Humidity.
Getting Started The wiring and power related instructions can be ordered separately: Document Title Doc. No. V Series Controller Wiring Diagram T61928 External Power Installation Instructions T61925 Door Wiring Instructions for Electrically–Operated T61926 Locksets Depending on the programming method you choose for the V Series System, you may need one or more of the following manuals: Document Title Doc. No.
Getting Started Best Access Systems Representatives provide telephone technical support for all V Series products. You may locate the representative nearest you by calling (317) 849-2250 Monday through Friday, between 7:00 a.m. and 4:00 p.m. eastern standard time; or visit the web page, www.BestAccess.com. Training seminars 1–10 BEST holds training sessions for its customers. If you are interested, you may contact your local BEST representative for the details.
2 SECURITY DEVICE MAINTENANCE The following pages contain exploded diagrams for all V Series Security Devices. These diagrams detail all field serviceable mechanical and electronic parts. Use the diagrams and parts lists on the following pages to find the part numbers you need.
15 13 11 19 17 21 11 9 7 24 5 23 1 3 1 20 3 14 V Series Service Manual 12 10 4 2 Figure 2.
Security Device Maintenance 8KV/9KV magnetic stripe trim parts list Refer to Figure 2.1 and the table below to find the part you need. Item Part No. Qty.
28 11 15 13 17 19 21 23 29 31 30 27 25 25 26 24 9 7 3 1 5 1 22 1 20 5 18 16 14 V Series Service Manual 12 6 4 2 Figure 2.
Security Device Maintenance 8KV/9KV keypad trim parts list Refer to Figure 2.2 and the table below to find the part you need. Item Part No. Qty.
28 29 17 11 19 25 21 23 31 31 27 25 15 13 26 9 7 1 3 24 5 3 22 20 5 18 16 14 V Series Service Manual 12 6 4 2 Figure 2.
Security Device Maintenance 8KV/9KV proximity trim parts list Refer to Figure 2.3 and the table below to find the part you need. Item Part No. Qty.
Security Device Maintenance 2–8 8KV/9KV EXPLODED CHASSIS DIAGRAM 11 21 20 10 6 19 9 8 18 17 16 7 8 15 6 5 14 4 3 13 2 1 V Series Service Manual Figure 2.
Security Device Maintenance 8KV/9KV chassis parts list V Series Service Manual Refer to Figure 2.4 and the table below to find the part you need. Item Part No. Qty.
5 1 7 9 11 11 13 15 17 19 3 28 27 26 2 25 21 22 23 1 24 20 18 16 V Series Service Manual 10 8 6 4 2 Figure 2.
Security Device Maintenance 34/35HV magnetic stripe trim parts list Refer to Figure 2.5 and the table below to find the part you need. Item Part No. Qty.
Security Device Maintenance Item Part No. Qty.
5 7 9 11 15 13 17 19 21 23 25 25 27 29 33 31 35 34 32 3 2 1 30 1 1 22 V Series Service Manual 10 6 2 Figure 2.
Security Device Maintenance 34/35HV keypad trim parts list Refer to Figure 2.6 and the table below to find the part you need. Item Part No. Qty.
Security Device Maintenance Item Part No. Qty.
5 7 9 11 13 15 17 19 21 23 25 25 27 29 31 33 35 34 32 3 2 1 30 28 3 22 14 V Series Service Manual 10 8 6 2 Figure 2.
Security Device Maintenance 34/35HV proximity trim parts list Refer to Figure 2.7 and the table below to find the part you need. Item Part No. Qty.
Security Device Maintenance Item Part No. Qty.
Security Device Maintenance 34/35HV CASE WITH DEADBOLT EXPLODED DIAGRAM 1 2 3 4 5 6 17 7 18 8 19 20 21 22 23 24 9 10 11 25 26 12 13 14 27 3 15 16 28 29 30 31 Figure 2.
Security Device Maintenance 34/35HV case with deadbolt parts list 2–20 Refer to Figure 2.8 and the table below to find the part you need. Item Part No. Qty.
Security Device Maintenance 34/35HV CASE WITHOUT DEADBOLT EXPLODED DIAGRAM 1 2 3 4 5 6 17 7 18 8 19 20 21 22 9 10 11 23 24 12 25 13 14 15 16 26 27 28 29 Figure 2.
Security Device Maintenance 34/35HV case without deadbolt parts list 2–22 Refer to Figure 2.9 and the table below to find the part you need. Item Part No. Qty.
Security Device Maintenance XV CONTROLLER EXPLODED DIAGRAM 12 1 2 11 10 3 O1 N 2 9 4 Figure 2.10 5 6 8 7 XV controller exploded diagram XV Controller parts list V Series Service Manual Refer to Figure 2.10 and the table below to find the part you need. Item Part No. Qty.
Security Device Maintenance not shown 1767179 1 Keypad reader (Lexan illuminated) not shown 1767210 1 Keypad reader (stainless steel finish) not shown 1767252 1 Magnetic stripe card reader (off-white finish) not shown 1767294 1 Magnetic stripe card reader (black finish) not shown 1789014 1 Motorola proximity reader I (beige finish) not shown 1788974 1 Motorola proximity reader I (black finish) not shown 1789056 1 Motorola proximity reader II (beige finish) not shown 1789098 1 Motorola
Security Device Maintenance PROGRAMMING PARTS DIAGRAM 1 7 6 2 5 3 4 Figure 2.12 Programming parts Programming parts list V Series Service Manual Refer to Figure 2.12 and the table below to find the part you need. Item Part No.
Security Device Maintenance CARD ENCODER PARTS DIAGRAM 4 1 3 2 Figure 2.13 Card Encoder parts Card Encoder parts list Refer to Figure 2.13 and the table below to find the part you need. Item Part No. Description 1 1754877 Card Encoder security device 2 1747021 Card Encoder power supply 3 1754751 Card Encoder 4 1754919 Card Encoder Software LOCK EXTERNAL POWER SUPPLY PARTS DIAGRAM 1 4 3 2 Figure 2.
Security Device Maintenance SPECIAL TOOLS DIAGRAM 4 1 2 3 Figure 2.15 Special tools Special tools parts list V Series Service Manual Refer to Figure 2.15 and the table below to find the part you need. Item Part No.
Security Device Maintenance FUNCTION DESCRIPTIONS HV Locks The following lists describe how the latchbolt, deadbolt, outside lever/knob, and inside lever/knob operates for each HV function.
Security Device Maintenance NV–Latch without key override Latchbolt operated by: ■ outside lever/knob—unless locked by internal motor drive mechanism ■ inside lever/knob Outside lever/knob locked by: ■ internal motor drive mechanism operated by time–activated electronic signal or by valid card/PIN KV Lock Outside lever/knob unlocked by: internal motor drive mechanism operated by time–activated electronic signal or by valid card/PIN ■ Inside lever/knob is always unlocked The following list describes how
Security Device Maintenance FUNCTION CONVERSION If you want to convert the function of an existing HV Lock, use the following table to determine the parts that you need. This table includes only the parts that are different.
Security Device Maintenance 34HV/35HV KNOB/LEVER CONVERSION If you want to convert an existing 34HV Lock (with knob) to a 35HV Lock (with lever), or vice-versa, use the following table to determine the parts that you need. This table includes only the parts that are different.
Security Device Maintenance READER CONVERSION HV reader conversion If you want to convert the reader of an existing HV Lock, use the following table to determine the parts that you need. This table includes only the parts that are different.
Security Device Maintenance Part type Part No.
Security Device Maintenance KV reader conversion If you want to convert the reader of an existing KV Lock, use the following table to determine the parts that you need. This table includes only the parts that are different. For example, to convert an 8KV Lock with a magnetic stripe card reader to a 8KV Lock with a Motorola proximity reader, you would remove the following parts: ■ ■ ■ 8KV outside escutcheon (C61405) Card reader (B61646) Outside wire harness (A61643).
Security Device Maintenance Part Type Part No. Description Electronics assembly C60303 Keypad reader electronics assembly Escutcheon gasket a. b. c. d. B60339 HID proximity reader with wake up electronics assembly B60338 Motorola proximity wake up electronics assembly A60316 Escutcheon gasket Proximity Mag. Kpd. HIDc Mot.
Security Device Maintenance REPLACING PARTS Caution Replacing batteries Before you handle the circuit board or any component on the circuit board, make sure that you are properly grounded using an electrostatic discharge (ESD) protection kit. When ordering an ESD protection kit, refer to the part number on page 2–27. Touching the circuit board without proper grounding can damage sensitive electronic components—even if you don’t notice any static discharge.
Security Device Maintenance The only purpose of the backup battery is to support the clock and memory if power is not available from the battery pack. After the batteries in the battery pack fail, the backup battery can maintain the clock and memory for several years. To replace the battery pack: Refer to Figure 2.16 and follow the steps below. 1. Open the battery compartment by removing the security screw and the battery compartment cover. Battery compartment cover Security screw Tabs Figure 2.
Security Device Maintenance 4. Position the new battery pack in the battery compartment. 5. Insert the tabs on the lower edge of the battery compartment door into the battery compartment. Swing the door closed. Install the security screw. Removing and reinstalling the inside and outside trim To remove the inside and outside trim: Refer to Figure 2.18 and follow the steps below. 1. Open the battery compartment by removing the security screw and the battery compartment cover. 2.
Security Device Maintenance To reinstall the inside and outside trim: 1. Holding the outside trim near its position on the door, feed the outside wire harness back through the wire hole to the inside of the door. 2. Reconnect the outside wire harness to the circuit board in the inside trim. Reconnect the motor wire connector and deadbolt sensing connector (for 30HV with deadbolt only). Note: It is possible to plug the battery pack into the motor connector and the motor wire into the battery connector.
Security Device Maintenance Caution Disconnecting the inside wire harness will cause all security device information to be lost and revert the security device to its factory default settings. You must reprogram the security device after disconnecting the inside cable harness. 8. Disconnect the inside wire harness from the circuit board in the inside trim. 9. Wait at least 30 seconds, then connect the new inside wire harness to the circuit board in the inside trim.
Security Device Maintenance To replace the outside wire harness: Note: Disconnecting the outside wire harness will not cause any security device information to be lost. 1. Remove the inside and outside trim. For instructions, see To remove the inside and outside trim: on page 2-38. 2. If you are replacing a keypad reader or proximity card reader, remove the gasket that covers the circuit board for the card reader. 3. Loosen the screw holding the harness clip and remove the clip. Save the clip. 4.
Security Device Maintenance Replacing the inside circuit board Caution To replace the inside circuit board: 1. Remove the inside and outside trim. For instructions, see To remove the inside and outside trim: on page 2-38. Before you handle the circuit board or any component on the circuit board, make sure that you are properly grounded using an electrostatic discharge (ESD) protection kit. When ordering an ESD protection kit, refer to the part number on page 2–27.
Security Device Maintenance 6. Connect the outside wire harness to the circuit board on the card reader. 7. Position the clip under the left mounting screw. Tighten the screw. 8. Reinstall the inside and outside trim. For instructions, see To reinstall the inside and outside trim: on page 2-39. To replace the keypad reader or proximity bezel: 1. Remove the inside and outside trim. For instructions, see To remove the inside and outside trim: on page 2-38. 2.
Security Device Maintenance Replacing the PROM The Programmable Read-Only Memory (PROM) stores the program that controls the operation of the V Series Security Device. From time to time, BEST might upgrade the PROM either to add new features and functions or to fix problems. Follow the instructions below to upgrade the security device by replacing the PROM. Circuit boards may be shipped without the PROM.
Security Device Maintenance 3. Insert the hook of the PROM removal tool in one of the notched corners of the PROM socket, as shown in Figure 2.20. Use the PROM removal tool to pry the corner of the PROM part way out of the socket. PROM socket PROM PROM removal tool CK T LO T LO CK CO RP. CO RP. Figure 2.20 Prying one corner of the PROM part way out of the socket [V Series electronic lock shown] 4. Insert the PROM tool in the opposite notched corner.
Security Device Maintenance To install the PROM: Refer to Figure 2.22 and follow the steps below. 1. Before inserting the new PROM, make sure that the PROM is oriented so that the flat corner of the PROM matches the flat corner of the socket. Caution Caution Make sure that the PROM is oriented correctly before inserting it into the PROM socket. The PROM will fit into the socket the wrong way! Installing the PROM incorrectly will damage the circuit board.
3 TROUBLESHOOTING EMERGENCY OPERATIONS Caution How do you enable communications if you have lost the token or forgotten the password? Before you handle the circuit board or any component on the circuit board, make sure that you are properly grounded using an electrostatic discharge (ESD) protection kit. When ordering an ESD protection kit, refer to the part number on page 2–27.
Troubleshooting 5. Locate the DIP switches on the circuit board in the inside trim and move switch 2 to the ON position. O N DIP switches O1 2 N Figure 3.1 Enabling communications using the DIP switches 6. Move switch 1 to the ON position. Both switches should now be in the ON position. 7. Move both switches back to the OFF position. It does not matter which switch you move first.
Troubleshooting To open a lock after complete battery failure: Refer to Figure 3.2 and follow the steps below. 1. To provide temporary power to the lock, connect the palmtop cable, with an external battery pack connected, to the base of the lock. Although the palmtop PC itself does not need to be connected to the cable, it will not cause a problem if it is connected. Palmtop cable Battery pack Figure 3.2 Connecting the palmtop cable to the base of the lock 2.
Troubleshooting TROUBLESHOOTING THE V SERIES ELECTRONIC LOCK This table summarizes the possible causes for certain lock problems based on visible and audible signals (LEDs, sounder, and whether access is granted or denied). The causes of failure are listed in the order of likelihood. (The most likely cause is first, and so forth.) Another helpful tool to use when troubleshooting the V Series Electronic Lock and the V Series Controller is the lock’s history of events.
Troubleshooting LEDs Sounder Access Possible causes include… Denied You should… a. Card reader needs cleaning. a. Clean the card reader head using a cleaning card for magnetic stripe card readers. b. Outside wire harness is damaged or disconnected. b. Check the outside wire harness. If it’s damaged, replace the wire harness. c. Card reader or keypad reader has failed. c. Replace the card reader or keypad reader. d. Foreign object is inserted in the card reader. d.
Troubleshooting LEDs Green Sounder Access Possible causes include… Denied a. Chassis type of cylindrical lock a. Change the programming setting for chassis is set to “mortise”. type to cylindrical. b. If the lock is a 9K, the spindle may be faulty. Lock is always unlocked. You should… b. If you can hear the chassis cycling, replace the chassis. Contact your local BEST representative for assistance. a. Lock may be in a door unlock a. Use the handheld terminal to check the door mode.
Troubleshooting TROUBLESHOOTING THE V SERIES CONTROLLER For readers with red and green LEDs and no sounder This table summarizes the possible causes for certain controller problems based on visible signals (LEDs and whether access is granted or denied). Causes of failure are listed in order of likelihood. (The most likely cause is first, and so forth.
Troubleshooting LEDs Access Possible causes include… You should… Green stays on Denied a. Communication token was used. a. Wait 1 minute for the lock communications to automatically expire, or use any token again to turn off communications. b. Micro-controller circuit board switches are in the ON position. b. Set the switches to the OFF position. c. Micro-controller circuit board is malfunctioning. c. Replace the micro-controller circuit board. d.
Troubleshooting For readers with a dual red/green LED and sounder LEDs Sounder Access Possible causes include… Green Green/ 2 short red tones flashing Green/ 2 short red tones flashing Green/ red flashing You should… Granted Condition is normal for a valid token. 1 long tone Green remains on This table summarizes the possible causes for certain controller problems based on visible and audible signals (LEDs, sounder, and whether access is granted or denied).
Troubleshooting LEDs Sounder Access Possible causes include… Door is always unlocked. a. Use the handheld terminal to check the door a. Controller may be in a door mode. If desired, change the door mode. unlock mode or passage mode. Setting the door mode to “Door unlock” means that anyone can access the door in this condition. b. Controller may be in a door unlock time zone. b. Use the handheld terminal to check the door mode and time zone settings. c. Locking device may not be connected properly. c.
Troubleshooting Alarm troubleshooting This table summarizes the possible causes of valid and false alarms based on the type of alarm (siren, strobe, or security system) indicated (or not indicated). The causes are listed in the order of likelihood. (The most likely cause is first, and so forth.) You notice… Possible causes include… A local alarm (the card or keypad reader’s own alarm sounds and/or displays). a. Door is propped open, triggering a. Secure the door.
Troubleshooting 3–12 V Series Service Manual
A GLOSSARY Battery pack Card reader Device that reads the information encoded on magnetic stripe cards or proximity cards. Chassis type Type of mechanical locking mechanism—cylindrical or mortise—used in an electronic lock. Communication token Token generally used for all security devices in a facility to access locks at any time for programming.
Glossary Door unlock time zone Electronic lock Emergency power ESD Facility code only door mode Handheld terminal Battery-powered, self-contained, electronically-controlled lock. Temporary, external power source, applied (through the communications port) to open a lock, usually in the event of a battery failure. Electrostatic discharge. Door mode that sets a security device to allow access to any token with a valid facility code.
Glossary Temporary communication token Temporary operator token Token User database Wire harness V Series Service Manual Token for temporary use that lets you communicate with a V Series Security Device programmed with factory default settings. Token that gives people temporary access to locks before the devices in a V Series System are permanently programmed. Access card or V Series personal identification number (PIN) used to access a door. All user tokens—up to 1000—defined for a lockset configuration.
Glossary A–4 V Series Service Manual
B SECURITY DEVICE HISTORY EVENT TYPES The table on the following pages describes in alphabetical order each history event that can be recorded at a V Series Security Device. For information about retrieving, viewing, printing, and deleting device history records, see the IPS User Manual.
Security Device History Event Types Security device history event types B–2 Event Description ACCESS GRANTED ADD CARD The device granted access to the indicated token. ADD CARD RANGE Using the handheld terminal, the indicated range of tokens was added to the device’s user database. CARD EXPIRED The device denied access to the indicated token because the token’s programmed expiration date was earlier than the current date.
Security Device History Event Types V Series Service Manual Event Description INVALID F-CODE The device denied access to the indicated token because the token’s facility code was not valid. INVALID ISSUE The device denied access to the indicated token because the token’s issue number was not valid. INVALID T-ZONE The device denied access to the indicated token because the token’s time zone was not in effect.
Security Device History Event Types B–4 Event Description POWER LOSS: 0X0_ The device lost power and may have performed an internal reset. Use the following table to understand the code. Code Meaning Internal reset 0x00 Reset code was cleared. N/A 0x01 Memory was corrupted. Yes 0x02 Real time clock was corrupted. Yes 0x04 Power was lost. No 0x08 Database version is incorrect, ROM change.
C INSTALLATION INSTRUCTIONS The following pages contain the KV Installation Instructions, HV Installation Instructions, and the V Series Controller Installation Instructions.
Installation Instructions C–2 V Series Service Manual
Installation Instructions for V Series 83KV/93KV–85KV/95KV Locksets Overview 2 Drill holes and install latch Note 1: If the door is a fabricated hollow metal door, determine whether it is properly reinforced to support the lock. If the door reinforcement is not adequate, consult the door manufacturer for information on proper reinforcement. Note 2: To locate the centerpoint of a hole on the opposite side of the door, drill a pilot hole completely through the door.
Note 1: Make sure that the locking pin fully locks into the rose liner. Note 2: Locksets will fit doors 1 3/4“ to 2 1/4“ thick. (A spacer is available for 1 3/8“ doors.) See the enlarged view for the correct rose adjustment for these thicknesses. 2 Drill two 5/16“ diameter holes halfway into the door. 3 Turn the boring jig over and repeat steps 1 and 2 from the opposite side of the door. Note: Replace the boring jig after 10 door preparations.
5 Making sure that the connector is properly aligned, connect the outside wire harness connector to the lower-right circuit board connector in the inside trim. Press firmly on the connector until it is fully seated. 9 Secure the throughbolt trim 11 Install battery compartment door 1 Insert the tabs of the battery compartment door into its mating slots and swing the door closed.
B E S T 2 Insert the control key into the core and rotate the key 15 degrees to the right. Figure 18 3 Insert the core and throw member into the knob or lever with the control key. 4 Rotate the control key 15 degrees to the left and withdraw the key. Note: Be sure to insert the correct throw member into the core: six-pin cores require the number “6” throw member; seven-pin cores require the number “7” throw member. Caution: The control key can be used to remove cores and access doors.
Installation Instructions for V Series 34HV–35HV Locksets Overview 2 Mark the vertical centerline of the lock on the door edge. 3 Mark the vertical centerline of the lock on both sides of the door as measured from the vertical centerline on the door’s edge. 4 Mark the horizontal centerline of the strike on the door jamb 3/8“ above the horizontal centerline of the lock.
4 ■ Caution: Check the lock for the correct function, hand, and bevel before drilling. Drill only those holes required for the function. Wire hole 7/8“ diameter Case set screw inside Concealed cylinder Drill holes Deadbolt sensing wires Cylinder hole 1 1/4“ diameter Motor wires Mortise case Figure 7 Knob/lever hole 7/8“ diameter Throughbolt holes 3/8“ diameter 6 Install mounting plates 1 Insert the outside mounting plate through the door and lock case.
Caution: If installing a lock with the turn knob function, make sure that the battery wires are not rubbing against the turn knob retaining ring. 5 Making sure that the connector is properly aligned, connect the outside wire harness connector to the lower right circuit board connector in the inside trim. Press firmly on the connector until it is fully seated. 9 Secure the throughbolt trim 1 Pull excess outside wire harness back through to the outside.
Caution: The auxiliary bolt must make contact with the strike plate, as shown in Figure 18. The auxiliary bolt deadlocks the latchbolt and prevents someone from forcing the latch open when the door is closed. If the incorrect strike is installed, a lock-in can occur. For magnetic stripe card electronic locks 1 With the BEST logo facing toward you, insert and remove the temporary operator card, as shown in Figure 19. The green light flashes and the locking mechanism unlocks.
V Series Controller Installation Instructions Use these installation instructions to install a V Series Controller. The controller allows the V Series electronics to be separate from a door’s locking mechanism and to be located up to 500 feet away from the locking mechanism. The controller provides V Series electronic features for use with electrically-controlled locking devices.
Table 1—Controller inputs and outputs Input/output Description Related DIP switches, jumpers, and programming tasks Backup battery input Input for the 4.8 volt nicad battery pack. In the event of a power failure, the battery pack temporarily powers the microprocessor until it can properly shut down. Before you install the controller, we recommend you charge the backup battery pack in the controller for at least 48 hours.
Table 1—Controller inputs and outputs Related DIP switches, jumpers, and programming tasks Input/output Description Reader communications input DATA terminal STRB terminal CARDPR terminal Input for an ABA signal consisting of a data signal and a strobe signal (and sometimes a card present signal). Note: The strobe signal sometimes is called “clock.
4 Connect the power supply to the controller board Caution: To prevent damage and injury, connect the power supply after all other connections have been made. Connect the 12 to 24 volts AC or DC at 0.75 amp power supply to the controller board’s power input. Refer to Table 1 and to Figure 1.
Handheld connector To communicate with a handheld, connect to handheld cable. 2 I C +5V HANDHELD GND SCL SDA J6 P1 J7 { GND VPP SPD SPC +5V BACKUP DIP switches See Table C. MFG.
Figure 2—Block diagram Figure 3—RS–232 wiring diagram T61920/Rev A 1768984 ER-7991-1 BEST ACCESS SYSTEMS Indianapolis, Indiana
D INDEX Numerics 34/35HV case part numbers for 2–20, 2–22 certifications and standards 1–7 exploded diagrams 2–10, 2–13, 2–16, 2–19, 2–21 function conversion for 2–30 function descriptions for 2–28 to 2–29 installation of C–1 knob/lever conversion for 2–31 reader conversion for 2–32 trim part numbers for 2–11, 2–14, 2–17 8KV/9KV certifications and standards 1–7 chassis part numbers for 2–9 exploded diagrams 2–2, 2–4, 2–6, 2–8 function description for 2–29 installation of C–1 reader conversion for 2–34 tri
Index for cleaning 3–5, 3–7, 3–9 if can’t insert 3–6 case assemblies part numbers for 2–11, 2–14, 2–17 case cover 2–20, 2–22 case cover mounting screws 2–20, 2–22 case mounting screws part number for 2–11, 2–14, 2–17, 2–20, 2–22 case sub-assembly 2–20, 2–22 certifications and standards 1–7 changing batteries 2–36 card reader or keypad reader 2–42 inside and outside trim 2–38 inside circuit board 2–42 inside wire harness 2–39 outside wire harness 2–41 PROM 2–44 chassis assemblies part numbers for 2–3, 2–5, 2
Index inside mounting plate part number for 2–11, 2–14, 2–17 inside rose liner part number for 2–3, 2–5, 2–7, 2–9 inside trim reinstalling 2–39 removing 2–38 inside wire harness part number for 2–3, 2–5, 2–7, 2–11, 2–14, 2–17 replacing 2–39 installation instructions 34/35HV C–1 8KV/9KV C–1 V Series Controller C–1 Intelligent Programmer Software 2–25, A–2 invalid facility code 3–4, 3–7 invalid time zone 3–4, 3–7, 3–9 invalid token number 3–7, 3–9 IPS crossover cable 2–25 IPS interface cable 2–25 K key overr
Index PROM definition of A–2 inserting 2–46 part numbers for 2–3, 2–5, 2– 7, 2–11, 2–14, 2–17, 2–23 reinstalling 2–44, 2–46 removing 2–44 proximity card readers part numbers for 2–7, 2–17, 2–24 proximity reader electronics assemblies part numbers for 2–7, 2–17 R reader conversion for 34/35HV 2–32 for 8KV/9KV 2–34 readers see keypad readers see magnetic stripe card readers see proximity card readers reinstalling card reader or keypad reader 2–42 communications port 2–41 inside and outside trim 2–39 inside w
