Assembly Instructions

ManualsBrandsEssentials for Living ManualsBedsWoven Collection 6895-3.WWA/NG Malay Standard King Bed, in White Wash Abaca Rope, Natural Gray Mahogany

PARTS LIST

CODE PARTS DESCRIPTION QTY

HEADBOARD 1

SIDE RAIL 2

FOOT BOARD 1

MIDDLE SUPPORT 1

MIDDLE LEG 1

CROSS BAR 8

SIDE BAR 2

ASSEMBLY INSTRUCTIONS

MALAY BED

PAGE 1 OF 5

HARDWARE LIST

CODE HARDWARE DESCRIPTION

QTY

A 8

B 9

C 17

D 8

E 8

F 1

G 1

H 16

BRACKETS

JCBC BOLT

M6 X 60MM SS

FLAT WASHER

M6 x Ø18MM SS

SPRING WASHER

M6 x Ø11MM SS

NUT M6

HEX KEY L4

WRENCH 10

FAB SCREW

Ø8 X 1.5'' SS

- PLEASE DO NOT DISCARD ANY OF THE PACKAGING UNTIL YOU HAVE

CHECKED ALL THE PARTS AND HARDWARE HAVE BEEN SUPPLIED.

- BEFORE YOU BEGIN ASSEMBLY, DECIDE ON THE HEIGHT YOU WOULD LIKE TO

SET THE CROSS BARS AS THEY CAN BE ADJUSTED TO DESIRED DISTANCE

FROM FLOOR (10”-13”).

- FOLLOW INSTRUCTIONS CLOSELY AS DEVIATION FROM THEM MAY VOID

YOUR WARRANTY AND PRESENT A POSSIBLE SAFETY RISK.

- IT IS RECOMMENDED THAT ASSEMBLY IS DONE ON A SOFT SURFACE LIKE

CARPET TO AVOID ANY DAMAGE.

-THOUGH NOT NECESSARY, IT IS ADVISED THAT ASSEMBLY BE COMPLETED BY

A TEAM OF AT LEAST TWO PEOPLE.

Summary of content (5 pages)

PAGE 1
ASSEMBLY INSTRUCTIONS MALAY BED PARTS LIST CODE 1 2 3 PARTS DESCRIPTION HEADBOARD SIDE RAIL FOOT BOARD HARDWARE LIST CODE QTY MIDDLE SUPPORT 1 5 MIDDLE LEG 1 6 CROSS BAR 8 7 SIDE BAR 2 PAGE 1 OF 5 QTY BRACKETS 8 B JCBC BOLT M6 X 60MM SS 9 C FLAT WASHER M6 x Ø18MM SS 17 D SPRING WASHER M6 x Ø11MM SS 8 E NUT M6 8 F HEX KEY L4 1 G WRENCH 10 1 H FAB SCREW Ø8 X 1.
PAGE 2
1 1 2 2 STEP 1 STEP 2 2 A 4 PIN 2 SELECT THE HEIGHT OF THE CROSS BARS (ENSURE 4 PINS OF BRACKETS FIT IN TO THE CROSS BARS) 1 2 3 2 STEP 3 PAGE 2 OF 5 STEP 4 ENSURE ALL BRACKETS ARE INSTALLED AT THE SAME HEIGHT POSITION BEFORE CONTINUING
PAGE 3
Available Height Options (4 Positions) In The Bottom 2 Holes 2nd Position 10'' 11'' The Lowest Position 2nd Position Go Up One Hole Again Or In The Top 2 Holes 3rd Position 12'' 3rd Position PAGE 3 OF 5 13'' The Highest Position
PAGE 4
F B 7 C A C D E 2 G STEP 5 STEP 6 MATCH POSITION OF CROSS BARS CHOSEN IN STEP 4 4 1 A MATCH POSITION OF CROSS BARS CHOSEN IN STEP 4 1 3 A STEP 7 PAGE 4 OF 5 STEP 8
PAGE 5
F F B B C C 4 C D E 5 G STEP 9 STEP 10 HEIGHT OF CROSS BARS CAN BE ADJUSTED AFTER ASSEMBLY 7 H 6 FOLLOW STEP 9-4 BACKWARDS TO RESET BRACKET POSITION THEN REPEAT STEP 4-9 H 6 ROTATE TO SET HEIGHT OF MIDDLE LEG ADJUST FOOT LEVELER 6 STEP 11 PAGE 5 OF 5 FINISH