748+ 24-Zone Control Panel Software Version 3.
Table of Contents Introduction...................................................................... 1 About This Manual................................................................ Features ............................................................................... Specifications ....................................................................... Accessories & Keypads........................................................ About Paradox............................................................
One-Key Regular Arming.................................................... One-Key Stay/System A Arming......................................... Arming using a keyswitch ................................................... Bell Squawk ........................................................................ Exit Delay............................................................................ Beep on Exit Delay ............................................................. Alarm Transmission Delay ............
Part 1: Introduction 1.1 About This Manual This manual provides all the information you will need to understand panel operation, features and functions. If you are familiar with other security control panels, we recommend that you read this manual at least once to familiarize yourself with panel features and programming. Please refer to the index for a complete list of this manual's contents.
1.4 Accessories & Keypads If you would like to obtain more information on the following keypads, security system accessories or other security products, please contact your local Paradox distributor or come and visit us at our web site http://www.paradox.ca • • • • 1.
Part 2: INSTALLATION 2.1 Location & Mounting Remove the printed circuit board, mounting hardware and keypad from the packaging inside the panel box. The circuit board should not be mounted into the back of the cabinet, until all cables are pulled into the cabinet and prepared for connection. Before mounting the cabinet, push the five white nylon-mounting studs into the back of the cabinet. Select an installation site that is not easily accessible to intruders.
battery charging is set at 700 mA, then only 1A is left for the auxiliary output. If the battery charging is set at 350mA, then 1.35A is available for the AUX output, but with a maximum of 700mA per output. Table 1: Current Consumption Table Modules Motion Detectors (see detector instructions for details) 636/646* LED Keypads 642* LCD Keypads 708 Ultra Stand-Alone Digital Dialer MG-RCV3 Wireless Expansion Module 2.3.
If the Bell/Siren output is not being used when connecting a bell or siren to an optional relay output, the [4] trouble indicator (see section 11.12.3) will always be on. To avoid this, connect a 1KW resistor across the bell output. 2.6 Programmable Outputs (PGM) Figure 6 The 748+ control panels includes two fully programmable output (PGM). When a specific event or condition occurs in the system, a PGM can be used to reset smoke detectors, activate strobe lights, open/close garage doors and much more.
Disabling 642 Keypad Zones: If the keypad zone input terminal is not being used, disable it by shorting the ZONE and COM terminals of the keypad with a 1KW resistor. Table 2: Keypad Zone Recognition If using an LED keypad simply set the Zone Select Jumper at the back of the keypad: Zone Select Jumper "OFF" = Keypad Zone 1 Zone Select Jumper "ON" = Keypad Zone 2 Note: If the zone select jumper is changed, the control panel will only recognize the change when the keypad is disconnected and re-connected.
2.9 Single Zone Input Terminal Connections The system hardware recognizes the following single zone input terminal connections. For more information on programming the options mentioned below refer to ZONE DEFINITIONS in section 7 on page 26. 2.9.1 N.C. Contacts, Without EOL Resistor Figure 11 If your security installation does not require tamper or wire fault detection, connect the detection devices and program the control panel as shown in Figure 11.
2.9.3 N.C. Contacts, Without EOL Resistor, With Tamper Recognition Figure 14 If your security installation requires tamper recognition, all detection devices must use normally closed contacts. Connect the devices and program the control panel as shown in Figure 14. This setup will communicate an open or closed zone to the control panel, displaying open zones on the keypad. The control panel will also communicate any detected tampers (cuts) as per Tamper/Wire Fault Recognition Options (see section 10.
2.10.1 N.C. Contacts, Without EOL Resistor If your security installation does not require tamper or wire fault recognition but you are using the ATZ feature, connect the detection devices and program the control panel as shown in Figure 17. Do not use devices with normally open contacts, as this will cause the system to remain in alarm. This setup will communicate the status of each device to the control panel (see Figure 16), displaying open zones on the keypad. 2.10.2 N.C.
2.11 Fire Circuit If your security installation requires the use of smoke detectors, define zone 3 as a "24-hour" fire zone; please refer to section 7.5. 2.11.1 Standard Installation Connect the smoke detectors to zone 3 as shown in Figure 20. Note that a fire zone must use a 1KW EOL resistor. If there is a line short or if the smoke detector becomes active, whether the system is armed or disarmed, the control panel will generate an alarm (see Fire Alarm Output Figure on page 28).
Part 3: ACCESS CODES 3.1 Installer Code Streamline - Section 00 D Hexa Programming - Addresses 000-002 Default: 748+ = 484848 Only the installer code allows you to program all control panel settings, except the Master and User codes. To program any setting in the control panel you must enter the programming mode by pressing the [ENTER] key followed by the installer code. The installer code contains six digits and each digit can be any value from 0 to 9.
Part 4: PROGRAMMING METHODS The 748+ Control Panels can be programmed using either the keypad or the Espload Software. We highly recommend programming the control panels using the Espload Software, as it simplifies the process and reduces the potential of data entry errors. You can also program the control panels manually by using a keypad. 4.1 Espload Software With the Espload Software, you can program the 748+ family of control panels remotely via modem or locally using an ADP-1 adapter.
Figure 22 4.2.2 Hexa Streamlined Section Programming This is an alternate method to Hexa Programming. The addresses (000-043 and 300-527) programmed in the Hexa Programming method are grouped into 67 sections where each section contains four addresses (i.e. section 00 = addresses 000003). Using this method allows you to program 8 digits (4 addresses) without having to exit and re-enter addresses. When entering the final digit, the software will automatically advance to the next section.
5) Enter 3-digit data (decimal) value; after entering data you do not need to press [ENTER], the software will automatically save the data into the selected address 6) Return to step 2 to continue programming or press [CLEAR] to exit programming mode 4.2.4 Feature Select Programming Addresses 062 to 126 are programmed using the Feature Select Programming method. In this method, every key in each address on the keypad represents an option or feature.
Part 5: PANEL SETTINGS FOR ESPLOAD 5.1 Panel Answer Options Streamline - Section 00 D Hexa Programming - Address 003 Default: Answering Machine Override Disabled & Maximum 8 rings The following two options will define how the control panels answer an incoming call from a computer using the Espload software. In order for the Espload software to remotely communicate with the control panel, call the installation site twice using the Espload Software.
5.3 PC Password Streamline - Section 01 D Hexa Programming - Addresses 006-007 This four-digit download password identifies the PC to the panel, before beginning the download process. Enter the same password into the Espload software and the control panel. If the passwords are not the same, Espload will not establish communication. Enter any hexa digits from 0 to F. [ENTER] + Installer Code + [10] [10] [6] + First 2 digits + [10] [10] [7] + Final 2 digits + [ENTER] 5.
5.9 Automatic Event Buffer Transmission Feature Select Programming D Address 088, key [2nd] Default: Automatic Event Buffer Transmission Disabled When the event buffer reaches 50% capacity, the control panel will make two attempts to establish communication with a PC. The control panel will call the Computer Telephone Number (see section 5.4) programmed at addresses 008 to 015. The Espload software must be in "wait for dial tone" mode.
Part 6: Event Reporting Figure 23 NO Account 1 and 2 Have the same number YES Account 1 and 2 Have the same number or System A = Account #1 System B = Account #2 Partitioned Section 08 Addresses 032 to 035 Monitoring Station Telephone Number #1 Sections 04 & 05; Addresses 016 to 023 Phone Number Monitoring Station Telephone Number #2 Sections 06 & 07; Addresses 024 to 031 Control panel will never transmit report codes Disabled OFF/OFF Related Features Alternate between the two monitoring station num
6.1 Reporting Options Feature Select Programming D Address 086, key [11] & [12] Default: Reporting Disabled When a specific event occurs in the system, the control panel will attempt to report the appropriate event code (if programmed) to the Monitoring Station. The four available Reporting Options described in the table below, define where the event codes are reported.
Figure 24 6.2 Monitoring Station Telephone Number 1 Streamline - Section 04 & 05 D Hexa Programming - Addresses 016-023 The control panel will dial the programmed telephone number when reporting an event code to the monitoring station computer (see Reporting Options in section 6.1). For example, if the alarm system is armed and a zone with a motion detector opens, the control panel may dial the telephone number in order to send the programmed event code to the monitoring station computer.
Both Monitoring Station Telephone Numbers must be programmed in order for event reporting to function properly 6.4 System Account Codes Streamline - Section 08 D Hexa Programming - Addresses 032-035 All report codes are preceded by a 3 or 4-digit system account code to ensure correct identification to the monitoring station, identifying from which security system the event originated. For example, if a zone opens, the control panel will first send the account code followed by the appropriate report code.
Table 7 - Contact ID Event Codes Event Code Addresses Contact ID Message System Event Alarms/Restores 400 to 447 Alarm/Restore on Zone 3 if 24Hr fire or 2-wire Arm/Disarm 402, 426 301 to 349 / 351 to 399 Burglary Zone # Contact ID Code # 130 Fire Alarm 110 Open/Close By User # 401 Zone Shutdown 448 to 471 Burglary Bypass # 573 Zone Tamper 472 to 495 Sensor Tamper 383 383 Zone Tamper Reset 510 Sensor Tamper Auxiliary Power Trouble 496 and 504 System Trouble 300 Bell Disconnect/Max.
Note:You do not need to program addresses 300-527 if using the Ademco Contact I.D. (all codes) format. If you plan to program most of the event code addresses, we suggest you use the Hexa Streamlined Section Programming Method as described in section 4.2.2. Otherwise, use the Hexa Programming Method as described in section 4.2.1. 6.6.
511 - 6.6.8 TLM Trouble Restore: Telephone line has restored after the TLM (see section 10.1) has detected the loss of a telephone line. Special Codes Streamline - Sections 64 to 67 D Hexa Programming - Addresses 512-527 Each address represents a special condition in the system. When one of these special conditions occur, the control panel will report the event code associated with the address. 512 - Test Report: The test report has been activated either manually (see section 6.
6.11 Report Zone Restore Options Feature Select Programming D Address 088; key [BYP] Default: Zone Restore Codes Transmit on Bell Cut-Off With the [BYP] key “Off”, the report codes programmed at addresses 424-447 (see Restore Codes in section 6.6.4) will only transmit if the zone has returned to normal after bell cut-off (see section 8.11). With the [BYP] key “On”, the codes will transmit as soon as the zone returns to normal (zone closure).
Part 7: ZONE DEFINITIONS Figure 25 Zone Speed (applies to all zones) Address 053 EOL Zones (applies to all zone inputs) Address 088; [MEM] key ATZ Zone Doubling (applies to all zone inputs) Address 090; key [8] Address 090; key [7] Partitioning (applies to entire system) Address 086; key [8] System A/Stay Zones Address 116; Keys [1] to [10 (0)] Note: If the system is not partitioned, zones will be defined as Stay zones System B Zones Addresses 120; Keys [1] to [10 (0)] Bypass Enabled Zones Address 124
7.1 Zone Speed Decimal Programming D Address 053 Default: 600mS The zone speed applies to all zones whether the system is armed or disarmed. The zone speed defines how quickly the control panel will respond to an open zone. The control panel will not display and/or respond to an open zone until the programmed zone speed elapses. All other zone definitions and options do not come into effect until the zone speed has elapsed. Example: The system is armed and the zone speed is set for 1.2 seconds.
• • • • The panel will send a fire loop trouble report (if programmed at address 500) to the Monitoring Station. A trouble indicator, key [11], and a fire zone indicator, key [3], will flash on the keypad. Alarms will generate an intermittent output signal (see Figure below), regardless of the system's current arming status. Alarms are always audible, regardless of other settings. Figure 26 7.5.
7.9.1 Entry Time Delay 2 Decimal Programming D Address 051 Default: 45 seconds This applies to all zones defined as Delay 2 (see Entry Delay 2 above). You can program the Delay 2 between 001 and 255 seconds. [ENTER] + Installer Code + [10] [5] [1] + 3-digit decimal value (001-255) + [ENTER] 7.10 Partitioning Feature Select Programming D Address 086, key [8] This feature divides the alarm system into two distinct systems, identified as "System A" and "System B".
7.13 Keypad Zone 1 Supervision Feature Select Programming D Address 090, key [11] Default: Disabled When using a keypad defined as keypad zone 1, enable this feature. When enabled, the control panel will verify the presence of a keypad and the keypad zone. For more information see Keypad Zone Connections in section 2.8. Key [11] "Off": Keypad Zone 1 Disabled Key [11] "On": Keypad Zone 1 Enabled [ENTER] + Installer Code + [10] [9] [10] + [11] On/Off + [ENTER] 7.
Part 8: ARM/DISARM & ALARM OPTIONS Figure 27 Esprit 748+ 31
8.1 Timed Auto Arming Feature Select Programming D Address 086, key [5] Default: "Timed" Auto Arming Disabled The alarm system will automatically arm itself at a specified time everyday. Note, as with regular arming, the system will not arm if a zone is open and will report a "late to close" to the monitoring. If this occurs, the system will not arm until the next day. The type of arming is dependent on the Auto Arming Options (see below). Program the Auto Arm Time as described below. 8.1.
Key [7] "Off": "One Key" Regular Arming Disabled Key [7] "On": "One Key" Regular Arming Enabled [ENTER] + Installer Code + [10] [8] [8] + [7] On/Off + [ENTER] 8.4 One-Key Stay/System A Arming Feature Select Programming D Address 088, key [8] Default: Disabled Press and hold the [11] key for 2 seconds to "Stay" arm the system if partitioning is disabled. If the system is partitioned, the control panel will arm System "A".
8.9 Alarm Transmission Delay Decimal Programming D Address 059 This time limit, set between 5 and 63 seconds, is the delay period before reporting an alarm to the monitoring station after an alarm condition. During this period, disarming the system will cancel all pending alarms and send the restore codes. Programming 000-004 in this address disables this feature. Maximum 30 seconds on UL listed systems. [ENTER] + Installer Code + [10] [5] [9] + 3-digit decimal value (005-063) + [ENTER] 8.
Part 9: PGM (PROGRAMMABLE OUTPUT) We strongly suggest using of the Espload software to program the PGMs. 9.1 PGM Types Streamline - Sections 09 - Hexa Programming - Address 039 These control panels have two programmable outputs (PGMs). When a PGM closes, a ground is supplied to activate any device or relay connected to it, providing up to a maximum of 50mA (UL 30mA). When a PGM opens, the circuit is opened from ground, therefore not providing any power to devices connected to it.
[ENTER] + Installer Code + [10] [5] [6] + 3-digit decimal value (001-255) + [ENTER] 9.3 PGM Options Streamline - Section 10 D Hexa Programming - Addresses 040 to 043 The PGM options define which sequence of events will trigger the PGM. The PGM options are virtually endless. Therefore, to list them in the manual is impractical. Table 8, contains a list of the most commonly used PGM options with the required 2-digit data for each address.
Part 10: OTHER OPTIONS 10.1 Telephone Line Monitoring (TLM) Feature Select Programming D Address 086, key [2nd] & [1] Default: TLM Disabled When enabled, the system verifies the existence of a telephone line every 4 seconds. After each successful test, the dialer LED (green light) on the control panel flashes briefly. If the test fails the LED flashes on and off until the control panel detects the telephone line again.
Key [4] "off" = Panic 1 silent Key [4] "on" = Panic 1 audible Key [5] "off" = Panic 2 silent Key [5] "on" = Panic 2 audible Key [6] "off" = Panic 3 silent Key [6] "on" = Panic 3 fire alarm [ENTER] + Installer Code + [10] [8] [8] + [1] to [6] On/Off + [ENTER] Silent operation: When using the panic keys or the PS1, the control panel will emit a single confirmation beep. The control panel will transmit the event codes programmed at addresses 513, 514, and 515.
"Tamper/wire" disabled Tamper/wiring failure recognition is disabled. Not permitted on UL listed systems. "Trouble" enabled Tamper/wiring failure will generate a trouble indicator (key [9]) and a trouble report code (see Tamper/Trouble Codes in section 6.6.6.) when the system is disarmed. "Silent alarm" enabled Tamper/wiring failure will generate a trouble indicator (key [9]), a trouble report code (see Tamper/Trouble Codes in section 6.6.6.
Part 11: USER/KEYPAD FUNCTIONS The innovative Esprit keypads take a new approach to security features and functions. Each numeral from 1 to 12 on the keypad respectively represents each zone from 1 to 12 on the control panel. When the [2ND] key flashes, press the [2ND] key to view zones 13 to 24, where keys [1] to [12] represent zones 13-24 respectively. When the zone light is "off", the status in the protected zone is normal. If the zone light is "on", this means the zone is open.
11.4 Stay Arming "Stay" arming allows the user to remain in the protected area while partially arming the system. This means that they can stay in and move around the establishment, while certain designated zones are armed. For example, entry/exit points like doors or windows, the basement, or perhaps all the zones on the perimeter of the establishment may be armed when going to sleep at night, while the other zones remain deactivated.
If a mistake is made entering the code or if a zone in the desired system is open when entering the code, the keypad will emit a "rejection beep" (beeeeeeep). When the access code is correctly entered, the keypad will emit a "confirmation beep" (beep-beepbeep). The keypad can display the status of both systems. When "System A" is armed, the [STAY] key and "ARM" indicator will remain on. If System B is armed, the "AWAY" key and "ARM" indicator will remain on.
11.10 Bypass Recall This feature permits users to reinstate the last zone bypass entries saved in memory. When the system is disarmed, the bypass entries will be erased. By using the "bypass recall" feature, you can reinstate the previous bypass entries saved in memory. While in the "bypass mode", press the [BYP] + [ENTER] keys and the previous bypass status will be re-established. This eliminates the need to re-enter the bypass entries every time the system is armed.
11.12.5 Maximum Auxiliary Current - Key [6] The illumination of the [6] key indicates that the auxiliary current has exceeded 1A. This will cause automatic shutdown of the auxiliary output. After opening the short or reducing the load, the panel will restore power to the auxiliary output following the dynamic battery test (approximately 60 seconds). 11.12.
Warnings Important Information This equipment complies with Part 68 of the FCC rules subpart D and CS03. Inside the cover of this equipment is a label that contains, among other information, the FCC registration number of this equipment. Notification to Telephone Company Upon request, customer shall notify telephone company of particular line to which the connection will be made, and provide the FCC registration number and the ringer equivalence of the protective circuit.
authority, or electrician, as appropriate. The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all of the devices does not exceed 100. terminal.
Class B digital devices, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Notes 48 Reference & Installation Manual
Esprit 748+ 49
For technical support in Canada or the U.S., call 1-800-791-1919 for English or 1-866-912-0600 for French, Monday to Friday from 8:00 a.m. to 8:00 p.m. EST. For technical support outside Canada and the U.S. call 00-1-450-491-7444, Monday to Friday from 8:00 a.m. to 8:00 p.m. EST. Please feel free to visit our website at www.paradox.ca. 780 Industriel Blvd., Saint-Eustache (Quebec) J7R 5V3 CANADA Tel.: (450) 491-7444 Fax: (450) 491-2313 www.paradox.
