Certification Exhibit FCC ID: ONTJETIR5US IC: 10491A-JETIR5US FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project: 13-2001 Manufacturer: Esprit Model Models: JETIR5LUS, JETIR5iUS, JETIR4LUS, JETIR4iUS User Manual 3998 FAU Blvd.
The JETI DUPLEX EX series of receivers are designated to operate with the JETI DUPLEX EX transmitters using the 2.4GHz band. Thanks to the fully digital and bidirectional communication between the transmitter and receiver the Duplex EX system offers many new features and concepts for the remote control pilot. An additional R5 auxiliary receiver can be used to complement the R9, R11, R14 and R18 receivers.
Operation: Operation of the DUPLEX system is very similar to a traditional FM system. We recommend that you switch on the transmitter first and then the receiver. The transmitter confirms the on state of the receiver sounding a short beep. When switching off the system we recommend that you switch off the receiver first and then the transmitter. Installation: Wrap the receiver with soft foam and position it as far as possible away from potential interference sources (servos, electric motors, ESCs).
one or more of the E4 EX expanders connected to the receiver Ext port. Bidirectional Signal Loss Alert: An alarm will sound if you lose the bidirectional telemetry data communication between your transmitter and receiver. This alarm simply means that at the given instant there is no data available from the telemetry sensors or other equipment connected to the receiver input (Ext. port).
Overview of Receiver Data Items Once in the Jetibox emulator the Tx screen is displayed, press the right arrow button to go to the Rx info screen. Then press the down arrow button to go the Rx introductory screen. The introductory screen displays the type of receiver. By pushing the right arrow button, more detailed receiver and transmitter data of can be displayed. Add Profi info Direct connection to a Jetibox will display the introductory screen.
- Signal Fault Delay: specifies the deadline after which the receiver outputs change due to signal loss to preadjusted positions of the particular outputs or after which they become switched off (due to setup of Signal Fault in the menu Out Pin Set). - Volt act/alarm: the first item shows the actual receiver supply voltage, the second value serves for the setup of the alert decision threshold.
-Signal fault: (valid for RSat and RMK) behaviour setup of the satellite receiver in case of signal loss. - Individual set: the behaviour of the output in case of a signal loss will be conducted by the setup of particulat channels in the menu Measurement/Setup – Setup of the output, where the behaviour of particular output channels in case of signal loss may be set – to repeating of the last deviation or to FailSafe.
This function is of use in case of a bidirectional connection of several receivers or satellite receivers. The output channel marked Sat 1 can be set to PPM signal mode only.
positions, out off – output switched off, FailSafe – transition to preset throw positions of individual outputs which may be set up in the FailSafe menu.
be co-located or operating in conjunction with any other antenna or transmitter.” THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Warning: Changes or modifications to this device not expressly approved by Esprit Model/Jeti USA could void the user’s authority to operate the equipment.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.
