User Manual
Table Of Contents
- Manufacturer: Esprit Model
- DC-DS-16-EN-Part 1.pdf
- DC-DS-16-EN-Part 2.pdf
- Stránka 18
- Stránka 19
- Stránka 20
- Stránka 21
- Stránka 22
- Stránka 23
- Stránka 24
- Stránka 25
- Stránka 26
- Stránka 27
- Stránka 28
- Stránka 29
- Stránka 30
- Stránka 31
- Stránka 32
- Stránka 33
- Stránka 34
- Stránka 35
- Stránka 36
- Stránka 37
- Stránka 38
- Stránka 39
- Stránka 40
- Stránka 41
- Stránka 42
- Stránka 43
- Stránka 44
- Stránka 45
- Stránka 46
- Stránka 47
- Stránka 48
- Stránka 49
- Stránka 50
- Stránka 51
- Stránka 52
- Stránka 53
- Stránka 54
- Stránka 55
- Stránka 56
- Stránka 57
computer radio control system
EN
4. 4.
9.2.12 Governor/Gyro
Typically, a gyro is used to stablize a model helicopter along its
vertical axis (rudder). One channel is reserved so that you may adjust
the gyro sensitivity (gain) from the transmitter. Also, a separate
channel can be reserved for the control of a throttle governor. The
governor can be enabled when you create the model or later from
the „Model >Basic Properties“ menu. This menu allows you to
adjust the settings for both of these output channels. The
Governor/Gyro settings can be set collectively for all flight modes by
selecting the “G-(globe)” symbol or you can allow individual
Governor/Gyro settings in each separate flight mode by sellecting
the “S-Separate” symbol.
1. Gyro Settings
By default, the gyro sensitivity is assigned to the three position „Si“
switch. This allows you to have three different settings (Position 1,
Position 2, Position 3) for the gyro sensitivity. You can always assign
this function to a different transmitter control element (knob, slider,
switch) in the „Model, >Function Assignment“ menu. The Gyro
settings can be set collectively for all flight modes by selecting the
“G-(globe)” symbol or you can allow individual Gyro settings in
each separate flight mode by sellecting the “S-Separate” symbol.
i) Free Mix Trim Settings
This item allows you to enable or disable whether trim functions will
influence the free mix or not.
j) Free Mix Control by Dual Rates
With this item you can activate or deactivate the “Slave Dual-Rate”
function for the free mix. This settings allows the slave output to be
affected by dual rate inputs. All adjustments can be visually
inspected right away in the servo monitor page by pressing the “F2
(Servo)” button. Pressing the “F5 (Ok)” button returns you back to
free mix screen.
3. Deleting a Free Mix
Press the “F3 (Del)” button to delete the highlighted free mix.
4. Configuration & Setting
A free mix programming screen can be accessed by highlighting the
selected mix and then pressing the “F4 (Edit)” button.
2. Governor Settings
If you have the governor function enabled, by default, the governor
sensitivity is assigned to the three position „Sg“ switch. This allows
you to have three different settings (Position 1, Position 2, Position 3)
for the governor sensitivity. You can always assign this function to a
different transmitter control element (knob, slider, switch) in the
„Model, >Function Assignment“ menu. The governor settings can
be set collectively for all flight modes by selecting the “G-(globe)”
symbol or you can allow individual governor settings in each
separate flight mode by sellecting the “S-Separate” symbol.