Datasheet

ManualsBrandsEspressif ManualsDevelopment ToolsPCB design board

ESP32-S3-DevKitC-1 v1.1

The older version: ESP32-S3-DevKitC-1

This user guide will help you get started with ESP32-S3-DevKitC-1 and will also provide

Summary of content (11 pages)

PAGE 1
ESP32-S3-DevKitC-1 v1.1 The older version: ESP32-S3-DevKitC-1 This user guide will help you get started with ESP32-S3-DevKitC-1 and will also provide more in-depth information. The ESP32-S3-DevKitC-1 is an entry-level development board equipped with ESP32-S3WROOM-1, ESP32-S3-WROOM-1U, or ESP32-S3-WROOM-2, a general-purpose Wi-Fi + Bluetooth® LE MCU module that integrates complete Wi-Fi and Bluetooth LE functions.
PAGE 2
ESP32-S3-DevKitC-1 with ESP32-S3-WROOM-1 Module The document consists of the following major sections: • Getting started: Overview of the board and hardware/software setup instructions to get started. • Hardware Reference: More detailed information about the board’s hardware. Hardware Revision Details: Revision history, known issues, and links to user guides for previous versions (if any) of the board. Related Documents: Links to related documentation.
PAGE 3
This section provides a brief introduction of ESP32-S3-DevKitC-1, instructions on how to do the initial hardware setup and how to flash firmware onto it. Description of Components ESP32-S3-DevKitC-1 - front The key components of the board are described in a counter-clockwise direction. Key Component Description ESP32-S3WROOM-1/1U/2 ESP32-S3-WROOM-1, ESP32-S3-WROOM-1U, and ESP32-S3-WROOM-2 are powerful, generic Wi-Fi + Bluetooth LE MCU modules that have a rich set of peripherals.
PAGE 4
Key Component Port Description to the chip, as well as for communication with the chip via the on-board USB-toUART bridge. Boot Button Download button. Holding down Boot and then pressing Reset initiates Firmware Download mode for downloading firmware through the serial port. Reset Button Press this button to restart the system. USB Port ESP32-S3 full-speed USB OTG interface, compliant with the USB 1.1 specification.
PAGE 5
Connect the board with the computer using USB-to-UART Port. Connection using ESP32-S3 USB Port is not fully implemented in software. In subsequent steps, USB-to-UART Port will be used by default. Software Setup Please proceed to Get Started, where Section Installation will quickly help you set up the development environment and then flash an application example onto your board.
PAGE 6
Retail Orders If you order a few samples, each board comes in an individual package in either antistatic bag or any packaging depending on your retailer. For retail orders, please go to https://www.espressif.com/en/contact-us/get-samples. Wholesale Orders If you order in bulk, the boards come in large cardboard boxes. For wholesale orders, please go to https://www.espressif.com/en/contact-us/sales-questions.
PAGE 7
ESP32-S3-DevKitC-1 (click to enlarge) Power Supply Options There are three mutually exclusive ways to provide power to the board: • USB-to-UART Port and ESP32-S3 USB Port (either one or both), default power supply (recommended) • 5V and G (GND) pins 3V3 and G (GND) pins • Header Block The two tables below provide the Name and Function of the pins on both sides of the board (J1 and J3). The pin names are shown in ESP32-S3-DevKitC-1 - front. The numbering is the same as in the Board Schematic (PDF).
PAGE 8
No. Name Type 1 1 3V3 P 3.3 V power supply 2 3V3 P 3.
PAGE 9
No.
PAGE 10
Pin Layout ESP32-S3-DevKitC-1 Pin Layout (click to enlarge) Hardware Revision Details Initial release Note Both versions of ESP32-S3-DevKitC-1 are available on the market. The main difference lies in that the RGB LED is connected to different pins.
PAGE 11
• ESP32-S3-DevKitC-1 PCB layout (PDF) • ESP32-S3-DevKitC-1 Dimensions (PDF) • ESP32-S3-DevKitC-1 Dimensions source file (DXF) - You can view it with Autodesk Viewer online For further design documentation for the board, please contact us at sales@espressif.com.