Specifications

ManualsBrandsESP ManualsCamcorderGuardCam LED

Combined security camera LED floodlight system

GuardCam LED Manual_Layout 2 11/04/2013 14:02 Page 1

Summary of content (12 pages)

PAGE 1
GuardCam LED Manual_Layout 2 11/04/2013 14:02 Page 1 Combined security camera LED floodlight system
PAGE 2
GuardCam LED Manual_Layout 2 11/04/2013 14:02 Page 2 IMPORTANT NOTES - PLEASE READ The requirement to install back up batteries has now been removed from the latest version of GuardCam. Time and date settings will now be maintained during mains power outages for a minimum of 72 hours.
PAGE 3
GuardCam LED Manual_Layout 2 11/04/2013 14:02 Page 3 Table of contents Contents of package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 GuardCam LED Motion Light with Video Camera . . . . . . . . . . . . . . . . . . . . . . . 4 Step 1 - Insert/remove SD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Step 2 - Installing the GuardCam LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
GuardCam LED Manual_Layout 2 11/04/2013 14:02 Page 4 GuardCam LED Motion Light with Video Camera Floodlight Cover High intensity LED 45º 45º 50º Waterproof cover 3 mode selection Camera lens PIR lens Low battery indicator 45º 45º 35º Step 1 – Insert/remove SD card Unscrew the waterproofed cover using provided Allen key, then insert the SD card until it automatically locks into place. If you need to remove the SD card, please press OFF button and take it out within 30 seconds.
PAGE 5
GuardCam LED Manual_Layout 2 11/04/2013 14:02 Page 5 Step 2 - Installing the GuardCam LED IMPORTANT - IF IN ANY DOUBT ABOUT THE INSTALLATION OF THIS PRODUCT, CONSULT A QUALIFIED ELECTRICIAN This product must be earthed Do not mount the unit against inflammable surfaces The motion detector will not operate correctly if it is installed: - Near the outlet of a central heating boiler - Near air conditioning plant - Pointing directly at moving vehicles - Within sight of reflections from moving water - Whe
PAGE 6
GuardCam LED Manual_Layout 2 11/04/2013 14:02 Page 6 Step 3 - Mounting your GuardCam LED 1. 1. Place plastic masonry plugs into desired surface aligning holes as shown below. Using an electric screwdriver, fasten mounting plate directly to surface using screws E. 2. Feed the cable through the back mounting box and bush the cable entry to avoid abrasion to the cable. 3. Wire the unit as follows: (Ensure all wires are connected securely and that no loose strands are exposed) Fig.
PAGE 7
GuardCam LED Manual_Layout 2 11/04/2013 14:02 Page 7 Step 4 - Adjusting the Settings (see Figs. 6 - 8) Time control: Turn the time control knob to ”+” side to increase the illumination time (7 minutes max.), turn the control knob to “ “ side to reduce the illumination time (5 seconds min.) Sensitivity control: Adjust the detector range of Passive Infrared Motion Sensor (± 2M ~ 10M) To perform a walk test turn the knob fully to the “ “ side until the indicator faces the "W" mark.
PAGE 8
GuardCam LED Manual_Layout 2 11/04/2013 14:02 Page 8 Audio mode: To Change audio mode press the audio mode button (Fig. 8). The audio mode will cycle through the available options on each push. Option 1 : Warning you are being recorded by a security camera Option 2 : Dog barking Option 3 : Self recorded message 1 (max 10 sec) Option 4 : Self recorded message 2 (max 10 sec) Option 5 : Off Recording your own messages (Fig.
PAGE 9
GuardCam LED Manual_Layout 2 11/04/2013 14:02 Page 9 Step 5 - Set the Date and Time and Video Mode This will allow the images taken by GuardCam to display the correct date and time it was taken. Push TIME/DATE SET button (see Fig. 10) for 3 seconds, The LCD screen will then flash 3 times, indicating you have entered Time/Date setting mode. 1.
PAGE 10
GuardCam LED Manual_Layout 2 11/04/2013 14:02 Page 10 Step 6 - Viewing Video Viewing image by computer through USB card reader supplied (see Fig. 11) Open SD card housing with allen key supplied Press OFF/REC button and remove SD card from the slot. Put the SD card into the USB card reader supplied, then insert the card reader into PC via a USB port and open Windows Media Player to view the video. Fig.
PAGE 11
GuardCam LED Manual_Layout 2 11/04/2013 14:02 Page 11 Technical Specifications Features and specification: PIR detection angle 160 Deg and detection range up to 10M Records 20 seconds image recording for image stream: 10fps at 480*640 Pixels Built in SD card slot for SD memory card SD card slot for additional storage, max memory size up to 32GB SD card spec.
PAGE 12
GuardCam LED Manual_Layout 2 11/04/2013 14:02 Page 12 General Information and Safety SPECIAL CARE INSTRUCTIONS The GuardCam LED Motion Light with Video Camera is designed to be weather resistant. Never attempt to immerse the unit in water or any other liquid. This will damage the unit and void the warranty. This product is designed to illuminate, video, and make verbal announcements. It will not prevent the commission of any act, legal or illegal.