User Manual Model: ES00M140, ES00M180 Version 1.
Before You Begin 1 Introduction .................................................................................................................... 3 1.1 Safety Information……………………………………………………………………... 3 1.2 Contents of the box .............................................................................................. 3 1.3 Hard disk installation ............................................................................................ 4 1.4 Front panel ................................................
1. Introduction 1.1 Safety Information • Before setting up the DVR, carefully read all the documentation that came with your package. • To prevent fire and shock hazard, never expose the DVR to rain or moisture. • If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer. • Before using the product, make sure all cables are correctly connected and the power cables are not damaged.
installation. Please connect the power cable to the appropriate socket, and the data cables to their corresponding connectors. 1. Loosen the cover screw 2. Remove the cover 4. Tighten the hard disk screw 5.Connect the data wire 7. Cover the machine 8. Tighten the cover screw 3. Insert the hard disk 6.Connect the power wire 1.
1.5 Rear panel 4CH 8CH (1) Video inputs (2) BNC outputs (3) Audio input (4) Audio output (5) USB (6) Network (7) Power supply (8) VGA output (9) Power Switch (ES00M140, ES00M180 without this switch) 1.6 Mouse Control You can use a mouse to operate the DVR as well. The mouse operates just like a mouse on a Windows PC. Please connect the mouse tone of the USB connectors (#5) in the back panel and please note that you can hot-plug the mouse.
Use the mouse to select menu items. 1.
ratio, low aberration and low interference. The image must be clear and has natural color in the appropriate brightness. Make sure the video signal stable and in good condition The video should be installed in the appropriate location where is away from backlighting and low illumination or adopts the better backlighting and low illumination compensation. The ground and power supply of the video and the DVR should be shared and stable.
can connect the low impedance earphone and active sound box or other audio output equipments through power amplifier. If the sound box and the tone arm can not be isolated, howling phenomena is often existed. There are some methods to deal with the above phenomena. 1. Adopt better directional tone arm. 2. Adjust the sound box volume to be under the threshold that produces the howling phenomena. 3. Use fitment materials that absorb the sound to reduce reflection of the sound. 4.
Playback Search mode Time searching, calendar searching, affair searching, channel searching, information searching Space Occupation Audio: 28.8MB/H Video:25～450MB/H And Recording storage Hard disk, network backup Backup mode Network, USB flash Drive Storage Video input 4 BNC 8 BNC Video output 2 BNC, 1 VGA Audio input Port Other 16 BNC 1 RCA 1 RCA Audio output 1 RCA Network port RJ45 10M/100M USB port 2* USB2.
Getting Started and Main Menu 2. Basic operation 2.1 Preview Note: The button in gray display indicates nonsupport. You can right click mouse to choose the switch between the windows. The system date, time and channel name are shown in each viewing window. The surveillance video and the alarm status are shown in each window.
2.2 Login System When the DVR boots up, the user must login and the system provides the corresponding functions with the user privilege. There are three user settings. The names are admin, guest and default and these names have no password. Admin is the super user privilege; guest and default’s permissions are preview and video playback.
menu, record mode, Search, PTZ control, Start Tour, Volume regulate, Logout, view1/4 screens. Note: Neither ES00M140 and ES00M180 have PTZ function 2.3.2 After logging into preview mode, you can right click the mouse to get a desktop shortcut menu. Right click mouse again and select the Main Menu 2.3.2.1 Record Mode Please check current channel status: “○” means it is not in recording status, “●” means it is in recording status.
2.3.3 Main menu navigation When you login, the system main menu is shown as below. Main menu Sub menu Search recording look-up, recording play, video file storage Set the recording configuration, recording type, recording time Record section HDD Set appointed hard disk as read-write disc, read-only disc or management redundant disc, clear data, resume date and so on Language Set language. Date/Time Set system time, data format and so on.
Exit Exit 2.3.3.1 Return last lever menu. Exit main menu and display Monitor. When the Main Menu appears, click the system icon in the main menu shown below: 2.4 System setup Set all the system parameters by clicking each icon .i.e. Language, Date/Time, Account, GUI Display, and Video. After setting all the parameters, click “Exit” on the System Menu.
2.4.1.1 Language Click [Language] Æ Select your language from the drop down menu. Then click “OK”. 2.4.1.
【Date format】Choose the data format: YMD, MDY, DMY. 【Date Separator】Choose list separator of the data format. 【Time Format】Choose time format: 24 hour or 12 hour 【DST】Click for Daylight Saving Time. Daylight savings time “On” means DST is enabled. You can setup the start time and end time of DST. 2.4.1.3 HDD Manage Configure and manage the hard disk. The menu displays current hard disk information: hard disk number, input port, type, status and overall capability.
2.4.2 Account Manage the user privilege Note： 1. The character length is 8 bytes at most for the following user and user team name. The blank ahead or behind the character string is invalid. The middle blank in the character string is valid. Legal characters include: letter, number, underline, subtraction sign, dot. 2. There is no limit in the user and user group. You can add or delete the user group according to user definition. The factory setup include: user\admin. You can set the team as you wish.
【Modify Pwd】Modify the user password. You can set 1-6 bit password. The blank ahead or behind the char string is invalid. The middle blank in the char string is valid. Note：The user who possess the user control privilege can modify his/her own or other users password Picture 4.10 Modify Password 【Add user】Add a user in the team and set the user privilege. Enter the menu interface and input the user name and password. Choose the team and choose whether cover using the user.
equipment, real time surveillance, playback, recording setup, video file backup and so on. Picture 4.12 Add Group 【Delete User】Delete the current user. Choose the user and click delete user button. 【Delete Group】Delete the current group. Choose the group and click delete group button. Picture 4.13 Delete Group 2.4.3 GUI Display Configure the video output parameters including the front output mode.
Picture 4.14 GUI Display 【Channel Title】Click the channel name modify button and enter the channel name menu. Modify the channel name. The 16 Chinese characters and 25 letters are supportive. 【Preview Time】means the selective state. Display the system data and time in the surveillance window. 【preview Channel】means the selective state. Display the system channel number in the surveillance window. 【Record Status】means the selective state. Display the system recording status in the surveillance window.
Note：If you press the “Default” button, all config will replace to default settings. 2.4.4 Video Configure the video parameters In the local preview mode include: Resolution, Video Standard, Tour Time and Output Adjust. Picture 4.16 Video 【Resolution】Set display resolution. 【Video Standard】Set the video standard as PAL or NTSC. 【Tour Time】Set the patrol switch interval. The set range is 5-120 seconds. 【Output Adjust】 Adjust TV output area parameters.
Adjust volume regulate parameters. You can use the desktop shortcut menu. Picture 3.17 Audio Adjust 【Volume regulate】You can set the volume regulate value from 0 to 100. 【Advanced】If you press this button then you will see picture as follow. Picture 3.18 Audio matches Channal You can match any or all channels which you want to match. But only one channel audio output valid at the same time. 2.4.5 Record Set the recording parameters in the surveillance channel.
—> —> To set the recording parameters click the “Record icon” on the Main Menu. You will set the recording parameters on the following screen. 【Resolution】Indicates the setup resolution and code rate for recording. There are four options: D1.HD1, CIF and QCIF. 【Frame Rate】In this section, you can choose the recording frame rate (frames per second) for the current channel. The higher the record frame rate, the more natural movement you will see in playback mode.
CHANNEL: You can select all channels or just one channel. You can also copy the settings from one channel to the other. —> 【REC. Size】It will pack by the time you selected. Click “OK” and “OK” again in each following menu to return to the Main Menu. Note: Neither ES00M140 or ES00M180 have “Alarm” function. 2.4.5.1 Region Cover When the video image is influenced by the environment such as bad brightness or reaching the set sensitivity parameter, the camera mask function is turned on. Picture 4.
2.4.6 Playback and Backup 2.4.6.1Search and Playback There are two methods for you to play the video files in the hard disk. 1、 In the desktop shortcut menu. 2、 Main menu -> Search. 1 2 4 5 6 Picture 3.6 video playback 1. Listed files 2. File information 3. File searching 4. File backup 5. Operation hint 6. Playback control 【Listed files】Look up the listed files that accord with the searching criteria. 【File information】Look up the found file information.
Button / Function Button Function Play/pause Backward Stop Slow play Fast play Previous frame Next frame Previous file Next file Circulation Full screen Table 3.2 Playback control key Note: Frame by frame playback is only performed in the pause playback state. 【Operation hint】Display the function of the cursor place. Special functions： Accurate playback：Input time (h/m/s) in the time column and then click play button.
—> 【Search】Use the Quick click button virtual keypad, then click the search button and enter the time period you want to search using the File type: Set the searching file type. HDD type: Set the searching hdd type. Channel: Set the searching channel. Start Time: Set the searching time scan. End Time: Set the searching time scan.
Note: If the recording mode is set to D1 resolution at 30 FPS for all 4 channels in the 4 channel DVR, the user can only use 2 channels for simultaneous playback. The User can either reduce the resolution or the frame rate of the recording setup in order to increase the number of channels the user can use for simultaneous playback. Note: After you playback, you can change the time based on the selected channel. If you want to change both time and channel, you need to start over the search function.
Picture 3.8 detect the storage Detect: Detect the storage connected with the DVR such as hard disk or universal disk. Erasure: Choose the file to delete and click erasure to delete the file. Stop: Stop the backup. Backup: Click backup button and the dialog box is popped up. You can choose the backup file according to the type, channel and time. Recording backup Remove：Clear the file information. Add：Show the file information satisfying the set file attributes.
2.5 Advanced Setup You can configure the Advanced parameters, In the local preview mode include: Mail, Version, Motion Detect, Mobile Monitor, Auto Maintain and Network. 2.5.1 Mail If the Motion Detect is turned on and are taken, send an email about the moion detect information (Text as Title only) to appointed address. Picture 4.18 Email SMTP server: Email server address. It could be an IP address or domain name. Domain name can be translated only it is the correct DNS configuration.
Picture 4.19 Version 2.5.3 Motion Detect When system detects the motion signal that reaches the set sensitivity, the motion detect alarm is on and the linkage function is turned on. Picture 4.20 Motion Detect 【Channel】Choose the set motion detect channel. 【Status】means that the motion detect function is on or off. 【Sensitivity】Choose in the six options according to the sensitivity.
【Region】Click setup and enter the set area. The area is divided into NTSC 12x16. Green block means the current cursor area. Yellow block means the dynamic detect defensive area. Black block means the unfenced area. You can set the area as follows, Drag the mouse and draw the area. Picture 4.21 Region 【Delay】Delay a few moments and stop when the alarm state is turned off. The range is 10~300 seconds. 【Delay】When alarm is over, recording will last some seconds(10~300sec),then stop.
【Enable】Select it to make sure abnormal function workable 【Port】 It’s a port of mobile monitoring which you need to make a router mapping of if want to visit it by mobile 2.5.4 Auto Maintain The user can set parameters include: Auto reboots time, System Upgrade, Default Settings, Log, Logout, Shutdown and reboot and so on. Picture 4.23 Auto maintain 【Upgrade】 Picture 4.25 Upgrade Upgrade Position: Choose USB interface. Upgrade file: Choose the file which needs upgraded.
Picture 4.24 Restore 【Log】 Look up system log according to the set mode. Log information include: system operation, configuration operation, data management, alarm affair, recording operation, user management, file management and so on. Set the time section to look up and click the look up button. The log information will display as a list. (one page is 128 items) Press Page up or Page down button to look up and press delete button to clear all the log information. Picture4.26 LOG 【logout】Quit the menu.
2.6 Network To connect the DVR to the internet, certain settings must be input to the DVR. To access your DVR from the internet, you will need either a Static IP from your internet service provider (IPS) or a router with Dynamic DNS (DDNS) capacity and an account with an online DDNS service. This service is country specific, but in many countries, you can use the manufacturer suggested service id http://www.dyndns.org. If the below parameters are not clear, please contact your network consultant for help.
【Media Port】Transfers video data between client and device, default is 34567 【Web Port】Sets up the port of IE browser via HTTP，default is 80 【IP Address】Set up the IP address 【Subnet Mask】Set up the Subnet mask 【Gateway】Set up the default gateway 【DNS】Set up the domain name sever . This will take you to the following screen. 【DDNS】Click the button 2.7 Web/ Remote View Open IE browser, input the correct IP address and port number, and you will see the following screen.
After you login, you will see the following screen.
[Main Stream] This choice will provide the user with the best image to view but will affect the frame rate the user can receive. [Extra Stream] This choice will provide the user with a lower grade image; however, the picture will run smoother due to the higher frame rate. [Auto Prompt] After logging in using the web viewing mode, the screen will auto prompt the window of stream choice to user when you select the function. 3. Appendix 3.
(3) Click “Customization level” to enter into the security Setting Set the ActiveX control and pluggable unit. Select the following options √ ActiveX control auto-prompting √ Run the script of the ActiveX control which is marked to safely implement the script. √ Implement initialization and run the script of the ActiveX control which is not marked to safely implement the script.
Step 4: Double click “Internet protocol (TCP/IP)”. Step 5: Examine the IP address, subnet mask, and default gateway on the PC. Step 6: Set the corresponding IP address, subnet mask, and default gateway on the DVR. If the subnet mask and default gateway on the DVR are the same as those of the PC, then the IP address must be in the same network section but cannot be the same as the used one. Otherwise, it will cause IP address conflicts. Take the figure above as an example, the IP address should be: 192.168.
5 FAQ and maintenance 5.1 FAQ If the problems are not listed, please contact the local service or call the HQ service. We are willing to offer the service. 1. The DVR cannot boot up normally. Possible reasons are as follows: a) The power supply is not correct. b) Switch power supply line is not in good connection. c) Switch power supply is damaged. d) The program updating is wrong. e) The hard disk is damaged or the hard disk lines are broken. f) The front panel is damaged.
Possible reasons are as follows: a) When using the BNC output, the option between the N mode or PAL mode is wrong and the image becomes black and white. b) The DVR is not matched the monitor impedance. c) The video transmission distance is too far or the loss of the video transmission line is too large. d) The color and brightness setting of the DVR is wrong. 6. I cannot find the video files in local playback mode. Possible reasons are as follows: a) The data line of the hard disk is damaged.
c) The connections are not correct. d) The PTZ setting of the DVR is not correct. e) The protocols of the PTZ decoder and the DVR are not matched. f) The address of the PTZ decoder and the DVR are not matched. g) When multiple decoders are connected, the far port of the PTZ decoder line A(B) must h) connect a 120 Ω resistance to reduce the reflection otherwise the PTZ control is not stable. The distance is too far. 12.
c) The data is too much. Please stop recording and backup. d) The data exceeds the backup storage. e) The backup equipment is not compatible. f) The backup equipment is damaged. 17. The keyboard cannot control the DVR. a) Possible reasons are as follows: b) The serial port of the DVR is not set correctly. c) The address is not correct. d) When multiple transformers are connected, the power supply is not large enough. Please give each transformer individual power supply.
xp system. 23. I cannot remember the advanced code or network code in the local menu operation. Please contact the local service or call the HQ service. We will offer the service according the machine type and the program edition. 4.2 Maintenance 1 Please brush printed circuit boards, connectors, fans, machine box and so on regularly. 2 Please keep the grounding well done to prevent the video or audio signal interfered and the DVR from static or inductive electricity.
