Install Instructions

ManualsBrandsErie ManualsHeating Supplies3/4" NPT 3-Way Pop Top Zone Valve, 4.0 Cv (120V)

SPECIFICATIONS

Valve

Service Hot and chilled water models, up to 50% glycol.

Steam models up to 15 psi (both valve body and valve

actuator must be rated for high temperature).

System Static Pressure Limits 400 psi (2758 kPa).

Close-off Refer to Table-2.

Fluid/Ambient Temperature Limits Refer to Table-1.

Seat Leakage ANSI class IV (0.01%) with pressure at inlet

(B-port/A-port, if 3-way).

Body Forged brass.

Stem Nickel-plated.

Seat Brass.

Paddle (VT series) Buna N.

Paddle (VS series) Highly saturated nitrile.

Actuator

Voltage 24 Vac @ 50/60 Hz, 110 Vac @ 50 Hz and 120 Vac

@ 60 Hz, 230 Vac @ 50 Hz, 240 Vac @ 60 Hz, 208 Vac @

50/60 Hz., 277 Vac @50/60 Hz.

Power Requirements 6.5 watts, 7.5 Va.

End Switch, 24 -240 Vac Models: 24 to 250 Vac/101 mA

min. to 5 A max. and 9 to 30 Vdc @ 100 mA max. 277 Vac

Models: 277 Vac/101mA min. to 5A max.

Control Signal On/off, 2 position, spring return.

Timing, Full Open to Full Close 25 Sec max for 60 Hz; 30

Sec max for 50 Hz; and 9 Sec max spring return.

Materials Stainless steel base plate, aluminum cover.

Ambient Temperature Limits:

Shipping & Storage -40 to 160 °F (-40 to 71 °C).

Operating Refer to Table-1.

Humidity 5 to 95% relative humidity, non-condensing.

Agency Listings Refer to your individual product label.

Shipping Weight (Actuator/Valve Assembly) 2.25 lbs

(1020 g).

Table-1 Valve Body and Actuators Model Chart

a: For steam applications both valve body and valve actuator must be rated for high temperature.

Example: VS2213G14A020 = Assembly. VS2213 = Valve body. AG14A020 = Actuator.

Model Temperature Range

VTXXXX

32 to 200 ×F (fluid) @ 104 ×F (Ambient)

(0 to 93 ×C @ 40 ×C)

VSXXXX

32 to 250 ×F (fluid) @ 169 ×F (Ambient)

(0 to 121 ×C @ 76 ×C), and/or 15 PSI (103 kPa)

Steama

AXX3XXX

32 to 200 ×F (fluid) @ 104 ×F (Ambient)

(0 to 93 ×C @ 40 ×C)

AXX4XXX

32 to 250 ×F (fluid) @ 169 ×F (Ambient)

(0 to 121 ×C @ 76 ×C), and/or 15 PSI (103 kPa)

Steama

Table-2 Flow Coefficients and Maximum Close-Off Pressure

Differential

Accessories for Inverted Flare Connection Valves

3/4" inverted flare bodies accept the following adapters to

copper pipe:

436-214-1 Union nut & elbow assembly, female for 1/2"

(5/8" O.D.) copper, 15/16" long

436-220 Union nut & coupling assembly, female for 1/2"

(5/8" O.D.) copper, 1-1/16" long

436-252 Union nut & coupling assembly, female for 3/4"

(7/8" O.D.) copper, 1-27/32" long

436-229-3 Union nut & nipple assembly, male for 1/2"

(5/8" O.D.) copper, 3" long

436-214-4 Union nut & elbow assembly, male for 1/2"

(5/8" O.D.) copper, 1-15/16" long

436-256 Union nut & coupling assembly, female for 1"

(1-1/8" O.D.) copper, 1-3/8" long

Valve

Size

2-way Cv

(kv)

3-way Cv

(kv)

(G)

Close-Off DP

PSI (kPa)

G = General close off actuator

(H)

PSI Close-Off

DP (kPa)

H = High close off actuator

1/2"

1.0 (0.9) 1.5 (30) 60 (414) 75 (517)

3/4"

1/2"

2.5 (2.2) 3.0 (2.6) 40 (276) 50 (344)

3/4"

1/2"

3.5 (3.0) 4.0 (3.4) 25 (172) 30 (208)3/4"

3/4"

5.0 (4.3) 5.0 (4.3) 20 (137) 25 (172)

3/4" 7.5 (6.5) 7.5 (6.5) 17 (117) 20 (137)

8.0 (6.9) 8.0 (6.9) 17 (117) 20 (137)

1-1/4"

Erie™ VT/VS PopTop™ Series

Two Position Spring Return Valves

General & High Close-Off PopTop Zone Valves

Installation Instructions

VT/VS Series with General

Close-Off Actuator

VT/VS Series with High

Close-Off Actuator

Summary of content (4 pages)

PAGE 1
Erie™ VT/VS PopTop™ Series Two Position Spring Return Valves General & High Close-Off PopTop Zone Valves Installation Instructions SPECIFICATIONS Valve Service Hot and chilled water models, up to 50% glycol. Steam models up to 15 psi (both valve body and valve actuator must be rated for high temperature). System Static Pressure Limits 400 psi (2758 kPa). Close-off Refer to Table-2. Fluid/Ambient Temperature Limits Refer to Table-1. Seat Leakage ANSI class IV (0.
PAGE 2
TYPICAL APPLICATION (wiring diagram) Honeywell - Terminal Block End Switch Honeywell - Wire Leads THERMOSTAT L1 Black (HOT) Motor L2 Black Red Red ES To Aux. Circuit Motor TR End Switch TH TR TH THERMOSTAT L1 To Aux. Circuit ES (HOT) L2 Erie Wire Leads Erie Terminal Block Black L2 TH Motor Red TR TH THERMOSTAT End Switch Red ES TH L1 (HOT) ES L2 Motor Black TR THERMOSTAT L1 (HOT) End Switch To Aux. Circuit To Aux.
PAGE 3
60 • In normal service, some condensation may occur on or around the valve. A drip pan may be necessary or the valve body may be insulated. Piping These valves must be piped so the paddle closes against the direction of flow. Flow is from B to A. Refer to Figure-6a to Figure-6f. When installing the actuator to a normally closed valve, the actuator must be placed in the manually open position by using the manual operating lever.
PAGE 4
Manual Operating Lever with the actuator to ensure the stem is inserted into the large mating hole on the bottom side of the actuator. Engage the actuator on the body and release the button. Release Button Manual Operating Lever Release Button CAUTION Do not use the valve body to manually open the actuator as damage to the valve actuator will result. Stem Mating Hole Mating Hole General Close-Off (G) CHECKOUT High Close-Off (H) 1.