Release Notes Ericsson W21/W25 Fixed Wireless Terminal for WCDMA/HSDPA Mobile Networks Release R11B/001 (7.
Release Notes Ericsson W21/W25 Fixed Wireless Terminal for WCDMA/HSDPA Mobile Networks Release R11B/001 (7.2 Mbps) Abstract These release notes describe the release history and installation notes that apply to the software Release of the Ericsson W21/W25. It also includes a summary of the main functionality that has been added/changed compared to the previous software releases as well as known issues.
Contents 1 INTRODUCTION...................................................................6 1.1 SOFTWARE DESCRIPTION ..........................................6 1.1.1 Hardware Compatibility ...........................................6 1.1.2 Configuration database ...........................................6 1.2 IMPORTANT UPGRADE INFORMATION ..........................7 2 RELEASE HISTORY ............................................................8 2.1 W25 SW RELEASE .......................................
3.8.1 3.8.2 3.9 3.9.1 3.10 3.10.1 3.10.2 3.11 3.11.1 3.11.2 3.12 3.12.1 3.12.2 3.13 3.13.1 3.13.2 3.14 3.14.1 4 4 New Functions.......................................................20 Corrections ............................................................20 RELEASE R9A006...................................................21 Corrections ............................................................21 RELEASE R8A006...................................................22 New Function...........................
4.1.19 5 31/109 47-CRH 102 167 Uen A – Oct 2008 Issue #5643, #5092 Remote update of PPP username/password, change of APN or change of Sip parameters is causing the WAN to restart.......33 TECHNICAL ASSISTANCE ...............................................35 5.1 W25 PRODUCT DOCUMENTATION ............................35 5.2 W21 PRODUCT DOCUMENTATION ............................35 5.3 TECHNICAL SUPPORT ..............................................
1 Introduction This document describes the release and installation notes that apply to the software release of the Ericsson W21/W25. It also includes a summary of the main functionality that has been added/fixed compared to the previous software release as well as known issues. SW Release No: 1.1 CXC 172 3158/001 R11B (7.2 Mbps) CXC 172 3409/001 R11B (7.2 Mbps) Software Description The W25-001-R11B010.zip and includes the following files: • • • w25-001-R11B010.
1.2 Important upgrade information W21/W25 Application Software needs to be version R9C or later, if your unit is running an earlier version DO NOT attempt this upgrade. Doing so will break your unit; it will need to be sent in for repair. For earlier version than R9C please see Release Note for release 1.3 (R9D). A reboot of your W2x before doing the upgrade is recommended. There are several ways to upgrade the FWT. Please see User Guide and Admin Guide for details.
2 Release History Refer to the Product Documentation listed in section 5.1 for further information about functionality and CLI commands. 2.1 W25 SW Release 2.1.1 CXC 172 3158 R11B010 – Oct 21 2008 This is a maintenance-release of the W25 software R11A. 2.1.2 CXC 172 3158 R11A011 – Jun 27 2008 This is a new release of the W25 software, 2.1.3 CXC 172 3158 R10C003 – Apr 28 2008 This is a maintenance-release of the W25 software R10. 2.1.
2.1.10 CXC 172 3158 R8A006 – June 29 2007 This is the official software release 1.2.5 for W25 2.1.11 CXC 172 3158 R6A019 – May 29 2007 This is the official software release 1.2 for W25. 2.1.12 CXC 172 3158 R4B001 – Feb 28 2007 This is the official software release 1.1 for W25. 2.1.13 CXC 172 3158 R4A010 – Feb 27 2007 This is an intermediate release for release 1.1. This must be used to upgrade to 1.1. 2.1.14 CXC 172 3158 R3D001 – Jan 30 2006 This is a customer hot fix of 1.0 2.1.
2.2.9 CXC 172 1560/3409 R6A019 – May 29 2007 This is the official software release 1.2 for W20/W21. 2.2.10 CXC 172 3409 R5B001 – Mar 09 2007 This is the official software release 1.1 for the new Ericsson W21.
3 Added Functions and Corrections This section shows new function and the correction history for each release. 3.1 Release R11B010 3.1.1 Corrections General: • Fixed FWT bug 5028: Updated OpenSSL • WAN-script will now check if /dev/modem is responding before attempting connection. If it's not responding then reboot radio module and try again.
Telephony related (W25 only): • Fixed bug 5554: US CLIP not working • Fixed bug 4933: Multiparty and call waiting features should now work according to expected US profile. • Fixed bug 5160: US market needs to be able to modify the incoming number before CLI is sent on the analog interface. • Fixed bug 5065: Play congestion tone when out of coverage. • Updated tones for au (rt_au.cfg), now revision 1.3.3 • Fixed bug 4653: In rare cases the end user experience one way media.
• Added forced informs: o .X_ERICSSONCOM_3GSMInterfaceConfig.Status.RSCP o .X_ERICSSON-COM_3GSMInterfaceConfig.Status.EcIo o .X_ERICSSONCOM_3GSMInterfaceConfig.Status.PLMNCode o .X_ERICSSON-COM_3GSMInterfaceConfig.Status.CGI o .X_ERICSSONCOM_3GSMInterfaceConfig.RadioModule.
address changes, an Inform is forced that includes the "4 VALUE CHANGE" event along with the actual name value binding.
• Fixed bug 4353: Progress information in WUI can be misleading. • Fixed bug 4409: Not possible to register to all frequency bands if default config is used • Fixed bug 4397: FWT won't register to WCDMA850 if all bands are enabled and prlregion != 03 • Fixed bug 4490: Not always possible to enter pin from handset. • Reworked the software installation (swinst) to reduce memory usage. Introduced a new image type (.
• Fixed bug 4409 and 4001:"Sometimes not possible to register to 1900 frequency bands if default config is used" • Fixed bug 4397 "FWT won't register to WCDMA850 if all bands are enabled and prlregion != 03" • Fixed bug 4291: "WUI show false signal level in 2G" • Fixed bug 4440 : PPP authentication PAP is not working Telephony related (W25 Only): • Fixed bug 4532: "Dial tone in Australian profile is incorrect".
3.5 Release R10A018 3.5.1 New Functions General: • The “st wan” command and WUI Internet page now displays traffic counters for the current and the previous month. • It should be possible to enter an Unlock-code via the WUI to unlock SIM-lock. The code is a random alphanumeric string, which can be delivered on request from Ericsson. • Enabled support so the unit can automatically load country telephony settings (i.e. market specifics setting e.g.
3.5.2 • Add SIP registration backoff algorithm that prevents the FWT to flood network with failed registration attempts • Added ability to enable/disable telephony per POTS line via cdb. • Added ability to configure SIP T1, T2, T4, transaction and registration timers via cdb. • Added ability to address a total of 5 different SIP servers (one at a time) when attempting to register. • Added ability to configure an outbound proxy backup.
• Changed source port for all locally generated SIP messages to be the same as configured listen port (i.e 5060). This port(s) was previously randomly selected.
3.6 Release R9D003 3.6.1 Corrections • Fixed bug #4279 upgrade problems due to memory constrains (see also R9C003). This software image is compressed with the new compression algorithm introduced in R9C003 and with the 7.2 Mbps firmware (2.0.7.0) for the radio module. 3.7 Release R9C003 3.7.1 Corrections • Fixed bug #4279 upgrade problems due to memory constrains. Introduced a better compression algorithm to support coming software releases. This saves memory during upgrade.
• Re-enabled the fax statistics log 3.9 Release R9A006 3.9.1 Corrections VoIP/FoIP related (W25 Only): • Bug 3733: SIP: FWT suddenly changes payload type. • Bug 3925: SSRC value in RTP header is not unique. • Changed source port for all locally generated SIP messages to be the same as configured listen port (i.e 5060). This port(s) was previously randomly selected. • Added T.38 codec parameters: o ecm, extended_ o roundtrip, o data_wait_time, o low_rate_recovery_packets.
• Issue #3972: "The scrambled PIN is visible for the end-user". Symptom/Change – The scrambled PIN (used when PIN-lock is enabled) is not visible any longer in syslog Others: • Changed default value in /etc/tel/t38.conf for the T.38 parameter "disable_ecm" to yes. • Changed default value in /etc/tel/t38.conf for the T.38 parameter " enable_extended_roundtrip" to no. • Updated telephony ring tone file for Australia. • Partly fixed bug 3992: "Failing SIP registrations leaks memory".
if the “Check now” button is pressed, the FWT will not immediately query the ACS. • Issue #3797 Fax fails after a WAN IP address change in FWT Symptoms – The function stops working after a WAN IP address change. Change: Added SIP de-registration attempt upon IPaddress change, before trying to re-register with new IP. • Issue #3717 All ACS "interval" queries will happen at the same time Symptoms – The FWT is supposed to query the ACS randomly with in +/- 3 hours from what's set in autoupdate.time.
• Added telephony tones and signals profile files for Austria New radio module firmware (1.1.6.4), which has the following fixes: • Fix issue where flood of small UL packets causes a reset of module • Fix Issue where continuous flood of small DL packets cause a reset.
3.11.2 • Every Power Management state change is logged as critical event in the system log. • Implemented battery status. • Added telephony tones and signals profile files for US, Sweden, Hungary and Spain. • Added telephony status information, "st tel" cli command. Displays hook state. • Implemented QoS marking for Fax over IP media and signaling traffic.
• Issue #3325 W25 overrings. Symptoms – A calls B, B never answers and A hangs up. Then B continues to ring another 3 "patterns" • Issue #3387 CLIR may not work. Symptoms – The CLIR Suppression IE setting in FWT and the Network CLIR settings can sometimes cause the number to be displayed at B-party. • Issue #3257 Password only use the first 8 letters. Symptoms/Change – WUI is now limited to 8 characters.
• 3.12.2 Add the the possibility to set PRL region via CLI. Note: The FWT needs to be rebooted after changing the PRL region. New parameter: cellular.prl_region (default=0) Corrections • Upgrade of the Radio module firmware to 1_1_6_3 and Bootloader 1_1_4_0. The following issues are solved: o PRL region is possible to set o Multi-RAB limitation, sometimes is not possible to do a CS voice calls when a HSDPA connection is established. o Missing notification when the B-subscriber hangs up 3.
• Issue #3132 and 3151: Phone rings twice…… Symptom/Change: Re-enabling the call suspend/resume timers upon hook events. Note: This also requires the new firmware in the Radio module, see R4B001. • Issue #3073: Block password login via SSH Symptom/change: It’s now possible to block password login via SSH. Set parameter ssh.password_authentication = false, then it’s not possible to login with password, only with correct key.
• Issue #3068 : SSL is not configured to prevent DNS hijacking" Symptom/change: Now hijack is not possible. 3.14 Release R3D001 3.14.1 New Function The following function is added: The FWT is configured to use the 3G network when the customer’s SIM is inserted in the FWT. This is a workaround until PRL Region is implemented.
4 Limitations and Restrictions 4.1 Known issues This section describes possibly unexpected behaviour in Ericsson W25 when running this software release. The following information is provided for each limitations and restrictions: Symptoms — A description of what is observed when the limitations and restrictions occur. Workaround — Solutions, if available, to counteract the limitations and restrictions. Status — Bug status. 4.1.
Status – Expected to be corrected in release R12 4.1.4 Issue #3128 FWT displays roaming network instead of an equivalent network Symptoms – In the WUI the Equivalent network is displayed as roaming network Workaround – None Status – Expected to be corrected in release R12 4.1.5 Issue #3125 Network name is displayed incorrect Symptoms – In the WUI the Network name is displayed incorrect Workaround – None Status – Expected to be corrected in release R12 4.1.
Status – Expected to be corrected in release R13 4.1.10 Issue #3802 2G.apn parameter ignored Symptoms – 2G.apn parameter ignored if 3G.apn is specified Workaround – Leave 3g.apn empty or use same apn for both 2G and 3G Status – No plans to fix this. Multiple apn will be introduced in W3x R12, which will change apn handling. 4.1.
4.1.15 Issue #5189 IPSec interoperability problems with Juniper Symptoms – Some IPSec interoperability problems have been discovered with Juniper firewalls. Workaround – None Status – Expected to be corrected in release R11B 4.1.16 Issue #5170 L2TP (BCP) tunnel to Cisco router Symptoms – Some problems with fragmentation of large packets have been noticed when terminating L2TP (BCP) tunnel in Cisco routers. Workaround – None Status – Investigation ongoing 4.1.
unsuccessfully by the ACS. However the CPE receives the new APN setting, starts a new session with the new APN and IP-address and is able to communicate with the ACS as normally. This is causing the ACS to terminate the session and not receiving the SetParameterResponse. The session finishes unsuccessfully. However, the PPPusername/password gets set in the CPE, and when the PPP interface comes up again the session is retried by the CPE.
5 Technical Assistance 5.
31/109 47-CRH 102 167 Uen A – Oct 2008
