ST.US.E10274.1 USER GUIDE RX8310/RX8315/RX8330 Distribution Receiver Software Version 1.3.0 RX8310/15/30 Distribution Receivers ENGLISH (UK) www.tandbergtv.
RX8310/RX8315/RX8330 Distribution Receiver Trademarks Dolby® / Dolby® Digital / AC-3® are registered trademarks of Dolby Laboratories Licensing Corporation. Customer Services Europe, Middle East and Africa: Tel: +44 (0) 23 8048 4455 Fax: +44 (0) 23 8048 4467 support@tandbergtv.com Americas: Tel: +888 671 1268 (US and Canada) Tel: +678 812 6255 (Outside of mainland US) noc@tandbergtv.com China: Tel: +86 10 6856 0260 (Beijing) Tel: +852 2530 3215 (Hong Kong) fieldservice-asia@tandbergtv.
RX8310/RX8315/RX8330 Distribution Receiver Contents 1 1.1 1.2 Who Should Use This User Guide? ...........................................................................5 What Equipment is Covered by This User Guide? ........................................................5 Hardware and Software Options....................................................................................5 2 2.1 2.2 2.3 2.4 2.5 Installing the Equipment .......................................................................
RX8310/RX8315/RX8330 Distribution Receiver 8 8.1 8.2 Disposal of this Equipment.......................................................................................23 General.........................................................................................................................23 For the European Union...............................................................................................23 9 Recycling ............................................................................
RX8310/RX8315/RX8330 Distribution Receiver 1 Who Should Use This User Guide? This User Guide is written for operators/users of the RX8310, RX8315 and RX8330 Distribution Receivers to assist in installation and operation. WARNING Do not remove the covers of this equipment. Hazardous voltages are present within this equipment and may be exposed if the covers are removed. Only TANDBERG Television trained and approved service engineers are permitted to service this equipment.
RX8310/RX8315/RX8330 Distribution Receiver Table 1.
RX8310/RX8315/RX8330 Distribution Receiver 2 Installing the Equipment 2.1 Introduction Use this User Guide for guidance on installation and operation. Only use installation accessories recommended by the manufacturers. 2.2 Operating Voltage CAUTION This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your business, consult a qualified electrical engineer or your local power company.
RX8310/RX8315/RX8330 Distribution Receiver RF IN 1,2,3,4 ASI OUT ASI INPUT ETHERNET 1 & 2 CVBS AUDIO OUT 1 & 2 TECHNICAL EARTH ALARM Figure 2.1: Rear Panel Connectors (RX8310/BAS) RF IN 1,2,3,4 IP OUT 1 & 2 AUDIO OUT 1 & 2 TECHNICAL EARTH CONDITIONAL ACCESS INTERFACE ASI OUT CVBS ASI INPUT ETHERNET 1 & 2 or CONTROL 1 & 2 ALARM CONDITIONAL ACCESS INTERFACE Figure 2.
RX8310/RX8315/RX8330 Distribution Receiver RF IN 1,2,3,4 IP OUT 1 & 2 AUDIO OUT 1 & 2 TECHNICAL EARTH CONDITIONAL ACCESS INTERFACE ASI / SDI OUT ASI / SDI OUT ASI / SDI OUT CVBS ASI INPUT ETHERNET 1 & 2 or CONTROL 1 & 2 ALARM CONDITIONAL ACCESS INTERFACE Figure 2.3: Rear Panel Connectors (RX8330/BAS with RX83XX/HWO/IP) Table 2.
RX8310/RX8315/RX8330 Distribution Receiver 2.5 Connecting the Receiver to the Power Supply WARNINGS 1. 2. 3. Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock As no mains switch is fitted to this unit, ensure the local power supply is switched OFF before connecting the supply cord. The Receiver is not fitted with an on/off switch. Ensure that the socket-outlet is installed near the equipment so that it is easily accessible.
RX8310/RX8315/RX8330 Distribution Receiver 3 Operating the Equipment From the Front Panel 3.1 Introduction The front panel display and keypad may be used to configure, control and monitor the Receiver when an external control system or PC is not used. NOTE Not all of the receiver User Settings may be viewed or changed from the front panel. The full set of User Settings may be found on the Web browser control interface.
RX8310/RX8315/RX8330 Distribution Receiver 3.3.2 Edit and Save Pushbuttons The edit and save pushbuttons are used to modify User Settings within the menu system. The edit pushbutton backlight is illuminated when the current menu contains a user modifiable setting. To modify a User Setting within a menu, press the edit pushbutton and then use the up and down pushbuttons to change the User Setting. During this edit operation, both the edit and save pushbutton backlights will be illuminated.
RX8310/RX8315/RX8330 Distribution Receiver 4 Operating the Equipment From A Web Browser 4.1 Introduction A PC Web Browser may be used to configure, control and monitor the Receiver. The PC must be connected to either of the two IP control ports on the rear of the receiver (labelled ETHERNET 1 and 2 or CONTROL 1 and 2). Before operation, the User Settings for the control port must be entered via the system menu on the front panel.
RX8310/RX8315/RX8330 Distribution Receiver Figure 4.1: Example Status Tab - Web Control for an RX8310 Receiver 4.3 Using the Receiver Web Browser Interface The User Settings that may be viewed or modified from the Web Browser interface are grouped together by function and are displayed on a number of pages. These pages can be viewed by selecting the relevant tabs. After any changes are made to User Settings, the ‘Apply Changes’ button must be pressed to action the changes. 4.
RX8310/RX8315/RX8330 Distribution Receiver • • • • • • Status: This page contains User Settings for: Unit name and IP address Input feed status Video decode status Audio decode status Decryption status Unit alarm status and log Device Info: This page contains User Settings for: IP Control Ports Set-up Unit and module build version details Fan and unit temperature status SNMP trap table Unit reset Alarms: This page contains User Settings for: Alarm filtering Alarm priority con
RX8310/RX8315/RX8330 Distribution Receiver • • • • • • 16 Output: This page contains User Settings for: Selection and configuration of the output feeds Download: This page contains User Settings for: Status of in-band software download.
RX8310/RX8315/RX8330 Distribution Receiver 5 Quick Start Guide - Using the Front Panel Control 5.1 Making Signal Connections to the Unit ! If you have an incoming satellite RF feed, connect this to the rear panel connector marked RF Input ! If you have an incoming ASI (Fiber) feed, connect this to the connector marked ASI Input ! Decoded PAL or NTSC video is output on connectors CVBS 1 and CVBS 2. These outputs are identical in operation.
RX8310/RX8315/RX8330 Distribution Receiver ! Select SAT input Set the LNB frequency Set the Satellite frequency Set the Symbol Rate Set the Modulation scheme and FEC Set the Roll-Off Set the set the LNB power output Set the set the LNB power output level A description of each of these User Settings can be found in the Reference Guide. NOTE If the unit has successfully locked to the incoming feed, then the TS Lock value in menu 2 should be LOCKED. 5.
RX8310/RX8315/RX8330 Distribution Receiver 5.4 Configuring the Video Output ! The unit will automatically decode the first video component that it finds within the selected service. ! An alternative video component may be selected from the service tab on the Web Control interface. NOTE If the incoming feed is High Definition video and the unit has the relevant decode licenses enabled then the output is automatically downconverted to Standard Definition at the CVBS connector. 5.
RX8310/RX8315/RX8330 Distribution Receiver 6 Equipment Packaging 6.1 Packaging Statement The outer carton and any cardboard inserts are made from 82% recycled material and are fully recyclable. 6.2 Packaging Markings The symbols printed on the outer carton are described below: Handle with care This way up Fragile Protect from moisture See Reference Guide for details of compliance with directives. See Reference Guide for details of compliance. Defines country of origin.
RX8310/RX8315/RX8330 Distribution Receiver The packaging is reusable per GB 18455-2001 This symbol guarantees that packaging with this symbol is recyclable and will be accepted by cardboard recyclers Recyclable per GB 18455-2001 21
RX8310/RX8315/RX8330 Distribution Receiver 7 Materials Declarations 7.1 Overview TANDBERG Television products are designed and manufactured in keeping with good environmental practise. Our component and materials selection policy prohibits the use of a range of potentially hazardous materials. In addition, we comply with relevant environmental legislation. 7.2 For the European Union For product sold into the EU after 1st July 2006, we comply with the EU RoHS Directive.
RX8310/RX8315/RX8330 Distribution Receiver 8 Disposal of this Equipment 8.1 General Dispose of this equipment safely at the end of its life. Local codes and/or environmental restrictions may affect its disposal. Regulations, policies and/or environmental restrictions differ throughout the world. Contact your local jurisdiction or local authority for specific advice on disposal. 8.
RX8310/RX8315/RX8330 Distribution Receiver 9 Recycling TANDBERG Television provides assistance to customers and recyclers through our web site http://www.tandbergtv.com/ProductRecycling.ink Please contact TANDBERG Television’s customer services for assistance with recycling if this site does not show the information you require.
