www.westlake.co.
User guide F251m terminal Fixed Cellular Terminal for Small office Home office (SoHo) applications
Content F251m ....................................................................... 7 USING CLI DISPLAYS........................................... 18 SUPPLIED PARTS................................................... 7 USING FAX MACHINES ....................................... 19 Sending a fax ............................................................ 19 Receiving a fax......................................................... 19 EXTERNAL CONNECTORS AND LIGHT INDICATORS...............................
Phonebook (abbreviated dialing) ............................. 30 Antennas ................................................................... 42 Voice mail ................................................................. 31 Power supply ............................................................ 42 Sending tone signals................................................. 31 FCT Data Reference Manual ................................... 42 Controlling call time (minute minder) .....................
Battery information................................................... 53 Ericsson Warranty..................................................... 55 Disposing of the battery ........................................... 54 What Ericsson will do .............................................. 55 Moving or storing the FCT ...................................... 54 Conditions................................................................. 55 Accessing the battery compartment .........................
Ericsson F251m First edition, November 2001 This manual has been published by Ericsson España, S.A. Bilbao Technology Centre, without any warranty. Improvements and changes to this manual needed by typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by Ericsson España, S.A. at any time and without notice. Such changes will, however, be incorporated into new editions of the manual. All rights reserved © Ericsson España, S.A.
F251m The F251m is a flexible and cost-effective solution for connecting your SoHo telephone system to the digital wireless GSM network.
External connectors and light indicators SIM card Antenna connector GSM radio indicator (green led) SIM card holder Power indicator (red led) Power connector Telephone interface RS232 port Maintenance connector 8 External connectors and light indicators / SIM card Your network operator provides you with a SIM (Subscriber Identity Module) card. The SIM card contains information about your telephone number and the services included in your subscription, among other things.
Connections Warning!: please, before you start any connections refer to section “Safe and Efficient Use” on page 51 in this guide and contact your network operator if you have any questions. Warning!: to get a good FCT protection against electrical discharges and the best audio quality, a good grounding of the power supply is strongly recommended.
The FCT is also equipped with an RS232 port that enables you to use it as a GSM modem for PC fax, data and SMS services. For this specific configuration, please refer to the FCT Data Reference Manual. See FCT accessories on page 41. The FCT is designed to provide a telephone line (RJ11 connector) that behaves in the same way as an analog trunk. • The PBX can be programmed to utilize Least Cost Routing (LCR), if available, to automatically choose the FCT trunk when suitable.
FCT connectivity to the ISDN 2B+D trunk of the PBX You need to follow these steps before you install the FCT on the wall and make all definitive connections. Warning!: the FCT should be switched off before inserting or removing your SIM card or connecting any devices to the FCT.
2. Remove the front cover. Open the SIM card holder and place the SIM in the right position. Switch on the FCT Connect the power supply. The FCT switches on automatically and the green and red light indicators start flashing. Enter PIN 3. Close the SIM card holder and place the front cover back in the previous position. Connect a telephone to the FCT Connect a fixed telephone to the FCT telephone line. Note: you will use this telephone to dial the PIN.
If the PIN is correct, you will hear a beep over the telephone (positive indication tone). If it is incorrect, a deep tone will sound (error indication tone). If the PIN is entered incorrectly three times, the SIM card will be blocked. If this happens, you can unblock it by using the PUK (Personal Unblocking Key), which you also get from your network operator. See SIM Card Security on page 33.
Wall mounting Location Testing Number of Green Light flashes Location status 0 Unacceptable 1 - - - 2 -- -- -- Good 3 --- --- --- Very good Please proceed as indicated in the following picture. 1) Fix the wall-mounting bracket on the wall Acceptable Steady ------------------------------- Excellent Please consider the following recommendations: • Always select an indoor location, preferably close to a window and the roof.
3) Shift the FCT down Warning!: once you have fixed the FCT to the wall and switched it on, check the final status of the red and green lights. If either one is off, there is a problem with the power supply or the GSM signal. See “Troubleshooting and FCT indicators” on page 35. Now the FCT is ready for connecting devices and making calls.
Checking connections GSM Network 32 RS2 Telephone Display Pc Telephone line Fax Pc Note: when making the connections, the two-wire telephone cable polarity does not affect at all. Tip: if your house or company is already wired with telephone cable, you only need to connect the cable to the FCT RJ11 connector and your telephone line will be up and running in all rooms. Note: it is strongly recommended that the telephone wire is installed indoors in order to avoid lightning damage.
Using telephones Fixed telephones connected to the FCT telephone line work in the same way as if they were connected to a fixed network. Warning!: you will not be able to make or receive data or fax calls while a speech call is ongoing. Note: you can also benefit from some FCT functionality that you do not usually have on your fixed network. See Advanced features on page 24. You can find detailed information about the tones that the FCT sends on Audible tones page 38.
Using CLI displays Devices that display the incoming number (telephones with display, external displays, etc.) can be directly connected to the FCT line interface in the same way as an ordinary telephone. If your subscription includes the Calling Line Identification (CLI) service and the caller´s network sends the number, the FCT will send the caller´s number towards your CLI display.
Using fax machines The FCT terminal allows the connection of Group 3 analog faxes to the FCT telephone line, in the same way as a telephone. Warning!: the fax communication service has to be registered with your network operator. Otherwise, the network will not allow faxes to be sent or received. Warning!: you will not be able to make or receive other calls while a fax communication is established Receiving a fax Incoming faxes are received in the same way as using the fixed line.
Using PCs Analog modems connected to the FCT telephone line work in the same way as if they were connected to the fixed line. In this way, you can use your PC standard modem to make data calls (Internet browsing, e-mail, etc.) through the FCT line. To be able to send and receive data calls, you need: – a PC equipped with an analog modem and the appropriate computer program (Web Browser, E-mail, etc). This is a standard configuration for most PCs in the market.
optionally, to improve the Internet connection, a DNS address and a Proxy address. All these settings will allow you to configure the Dial-up Networking program in your PC in order to establish a GPRS connection. Note: this procedure is similar to the way you configure an Internet connection from a specific ISP (Internet Service Provider). If your network operator has provided you with an installation guide, please follow the instructions included in the guide.
send the CNG tone so that the data call is made automatically by the FCT. Incoming data calls are received in the same way as using the fixed line. Note: if you have a SIM card that does not support separate voice and data numbers, the FCT does not recognize the type of incoming call. This means that the calling party will have to inform you each time a data call is about to be made. In this case, dial *9902# to prepare your FCT to receive a data call.
Using PBX For a PBX connection, first, you should: • Check that the PBX fulfills the requirements for FCT connectivity. See Installing an FCT connected to a PBX on page 10. • Follow all FCT installation steps specified in Preparing your FCT and Installing the FCT on the wall on page 13. Warning!: the PBX may require specific programming; both, programmation and installation should be done by specialized service personnel.
Advanced features If a DTMF telephone is connected to the FCT, the following features can be accessed. Changing volume During a call, you can increase or decrease the reception volume level. • Increase volume: dial R#### • Decrease volume: dial R**** Diverting calls (call forward) You can divert incoming calls to another phone number when you are unable to answer. The following table shows the divert alternatives as well as the way to proceed to manage this function.
To manage diversion of calls … Always When busy When no answer When out of reach All With Function … Dial … You will hear… Activate **21*Phone_number# 1 beep Deactivate ##21# 3 beeps Check status *#21# 1 beep if activated 3 beeps if deactivated Activate **67*Phone_number# 1 beep Deactivate ##67# 3 beeps Check status *#67# 1 beep if activated 3 beeps if deactivated Activate **61*Phone_number# 1 beep Deactivate ##61# 3 beeps Check status *#61# 1 beep if activated 3 beeps if
Restricting calls (call barring) You can restrict certain types of calls that can be made or received. You need a password to turn a call restriction on or off. Initially, this password will be 0000. We recommend you to change it by dialing: **03**OLD_PASSWORD*NEW_PASSWORD* NEW_PASSWORD# The following table shows the restriction alternatives as well as the way to proceed to manage this function. Warning!: these dialing sequences may vary depending on your network operator.
To manage restriction of calls … All outgoing calls All outgoing international calls All outgoing international calls except your home country All incoming calls All incoming calls when you are abroad All With Function … Activate Deactivate Dial … *33*Password# #33*Password# Check status *#33# Activate Deactivate *331*Password# #331*Password# Check status *#331# Activate Deactivate *332*Password# #332*Password# Check status *#332# Activate Deactivate *35*Password# #35*Password# Check stat
Note: if instead of hearing beeps you hear a deep tone, this means that there has been an error in the activation or deactivation. More than one call (call wait, call hold, call transfer, multiparty call) You can handle more than one call simultaneously. For example, you can put an ongoing call on hold, while you make or answer a second call, and then switch between the two calls. You can also set up a conference call to have a joint conversation with up to four people.
• To ignore the waiting call, take no action. • To continue with the ongoing call and reject the waiting call (give a User Busy indication tone to the waiting call): press R0. • To end the ongoing call and answer the waiting call: press R1. Note: if you hang up the telephone, you will also end the ongoing call and the telephone will ring again so that you can answer the waiting call as a normal call. • To put the ongoing call on hold and answer the waiting call : press R2.
Phonebook (abbreviated dialing) You can store telephone numbers in either the SIM card memory or the FCT memory. Up to 99 telephone numbers can be stored in each of them. The following table shows how to manage the phonebook with the 99 memory positions (Pos). Warning!: Pos has to have always two digits.
Voice mail To manage minute Dial… You will hear… minder function… The answering service of your network allows callers to leave a voice message when you cannot answer your calls. If you have voice mail, you will hear 3 beeps before the dial tone, as soon as you pick up the receiver to make a call. Note: if you have the DA20 display adapter accessory (See “FCT accessories” on page 41), a a icon will show when you have voice mail.
To manage the hot line … Dial … You will hear… Activate **53*Phone_number**timer# 1 beep Deactivate #53# 3 beeps service *#53# 1 beep if activated 3 beeps if deactivated service and phone number *#53*Phone_number# 1 beep if activated 3 beeps if deactivated service, phone number and timer *#53*Phone_number**timer# 1 beep if activated 3 beeps if deactivated Check status for… Note: if instead of hearing beeps you hear a deep tone, this means that there has been an error in the activation or
To manage alternate line Dial … You will hear… service function … Activate Line 1 **591# 1 beep Activate Line 2 **592# 1 beep Check status Line 1 *#591# 1 beep if activated 3 beeps if deactivated Check status Line 2 *#592# 1 beep if activated 3 beeps if deactivated Note: if instead of hearing beeps you hear a deep tone, this means that there has been an error in the activation or deactivation. SIM card security To manage your SIM card Most SIM cards are locked at the time of purchase.
To unblock your SIM card while changing your PIN In order to unblock your SIM card and change the PIN at the same time, please dial the following sequence: **05*PUK*NEW_PIN*NEW_PIN# 34 Advanced features
Troubleshooting and FCT indicators This chapter describes the procedures to identify and, if possible, correct problems that might occur with the FCT or its installation. Some problems require that you call your network operator, but most problems you encounter you can easily correct yourself. Note: if you have the DA20 accessory display (See “FCT accessories” on page 41), a “NO NETWORKS” message will show on your display when no network is available.
Simultaneous flashing 1 flash synchronized Red - - - - - - - Green - - - - - - - - Alarm status ENTER PIN ENTER PUK INSERT SIM SIM ERROR WRONG NETWORK WRONG SUBNETWORK WRONG SIM 2 flashes synchronized Red - - - - - - - Green - - - - - - - 3 flashes synchronized Red - - - - - - - - - - - Green - - - - - - - - - - - - FCT LOCKED WRONG XXXCK (where XXX is the name of the specific password) FCT FAILURE Do this … Insert the correct PIN. See Enter PIN on page 11. Insert the correct PUK.
Light indicators status If you see… Red light Green light ON ON or flashing Both lights OFF Red light Green light ON OFF It means… • AC power is ON • The FCT is connected to cellular network and available for use Normal operation mode • AC Power is OFF Red light Green light • AC Power is ON • The FCT is not connected to the cellular network and is not available for use • AC power is OFF.
Audible tones The FCT generates audible tones in your telephone set, thus providing the same service characteristics as the one given by the traditional fixed network. The following table describes the nature of the main tones you will get when using the unit. Other standard call progress tones, such as busy tone, number obtainable or ring back tone, are provided directly by the network. Note: some tones can vary depending on your network operator.
FCT technical data GSM AIR INTERFACE Frequency Bands: Triple-Band E-GSM 900, GSM 1800 and GSM 1900 E-GSM 900 Frequencies: TX 880-915 MHz, RX 925-960 MHz RF power: Maximum 2 W (33 dBm), Power class 4 GSM1800 Frequencies: TX 1710-1785 MHz, RX 1805-1880 MHz RF power: Maximum 1 W (30 dBm), Power class 1 GSM1900 Frequencies: TX 1850-1910 MHz, RX 1930-1990 MHz RF power: Maximum 1 W (30 dBm), Power class 1 Data capabilities: multislot GPRS Class B and HSCSD (Data rates depend on GSM operator services) Speech codec
RS232 INTERFACE • Data services: all applicable GSM 7.07 AT commands • SMS: all applicable GSM 7.
FCT accessories The F200 series terminals benefit from a wide range of accessories, which ensure the best and easiest way to install, serve and maintain the terminals, enhancing their functionality. Only these approved-by-Ericsson accessories will guarantee the quality and performance of the terminals.
• FCT phone line direct feeding • FCT real-time status indication: operator’s name, radio signal… • Calling Line Identification (CLI) • List of incoming calls • SMS received display and storage (Very useful functionality for pre-paid subscribers) Antennas In areas where coverage is poor, the following accessory antenna can be used to enhance the FCT performance: • External triple band omnidirectional antenna. For installation or in places where indoor coverage is unstable. Band: triple 900/1800/1900 MHz.
Annex: PC data configurations Windows 98 GPRS set-up Warning!: your PC must have the Dial-up Networking and the TCP/IP protocol installed within the network components. You can check this in ‘Start->Settings->Control Panel’ and double clicking on ‘Network’. If not, these components have to be previously added from your Windows installation disk. To configure your GPRS connection under Windows 98 in your PC, follow steps 1 to 9: 1) Go to ‘My Computer’ and double-click ‘Dial-Up Networking’.
4) Click on ‘Finish’. 6) In the ‘General’ tab, turn off ‘Use area code and Dialing Properties’. 5) In the ‘Dial-Up Networking’ folder, right-click on the created connection and select ‘Properties’. 7) In the ‘Server Types’ tab: – ‘Type of Dial-Up Server’: select ‘PPP: Internet, Windows NT, Windows 98’ from the list.
below with primary and secondary DNS addresses provided by operator being 111.111.111.111 and 222.222.222.222) – ‘Use IP header compression’ optional. – ‘Use default gateway on remote network’ turned on. 8) Push the ‘TCP/IP Settings…’ button. – ‘Server assigned IP address’ must be checked. – ‘Server assigned name server addresses’ must be set if the network operator requires it. If the network operator provides DNS addresses, then these must be added once ‘Specify name server addresses’ is marked.
You have now installed the GPRS connection. To connect to the GPRS network, follow steps 1 to 3: 1) Go to ‘My Computer’-> Dial-Up Networking’ and open the previously configured connection. 2) Type the user name and password provided by your network operator and verify that the telephone number is *98#. Then press ‘Connect’. Note: if your network operator has provided you with a Proxy Address, you should configure your Web browser (Internet Explorer, Netscape, etc.) accordingly.
To configure your GPRS connection under a Windows NT PC, follow steps 1 to 8: 1) Go to ‘My Computer’ and double-click ‘Dial-Up Networking’. 2) If there are no previously configured connections, the following wizard will show up. Type a name for the connection and tick ‘I know all about phonebook entries and would rather edit the properties directly’. Then click on ‘Finish’; edit properties of this new connection and go to step 4) to continue with the configuration.
5) In the ‘Server’ tab select ‘PPP: Windows NT, Windows 95 Plus, Internet’ from the ‘Dial-up server type’ list. Be sure that ‘TCP/IP’ is the only ticked protocol within the ‘Network protocols’ box. 48 Annex: PC data configurations 6) Push the ‘TCP/IP Settings…’ button. – ‘Server assigned IP address’ must be checked. – ‘Server assigned name server addresses’ must be set if network operator requires it.
– ‘Use IP header compression’ optional. – ‘Use default gateway on remote network’ turned on. 7) Press ‘OK’ and go to the ‘Security’ tab. Select ‘Accept any authentication including clear text’. 8) Click ‘OK’ all the way to update the configuration. You have now installed the GPRS connection. To connect to the GPRS network, follow steps 1 to 3: 1) Go to ‘My Computer -> Dial-Up Networking’ and select the Dial-Up Networking connection previously configured. Verify that the telephone number is *98#.
3) Once you are connected, you may use your connection as an ordinary Internet connection. Note: if your network operator has provided you with a Proxy Address, you should configure your Web browser (Internet Explorer, Netscape, etc.) accordingly. 2) Type the user name and password provided by your network operator. If a ‘Domain’ field is present, then leave it blank.
Safe and efficient use Note: please read this information before using your FCT. Save this user guide since it contains important safety information and operating instructions. shock or injury. The warranty does not cover product failures that have been caused by use of non-Ericsson original accessories. • Treat your product with care. Keep it in a clean and dust-free place. Antenna care Product care • Do not expose your FCT to liquid or moisture.
Radio frequency energy Your FCT is a radio transmitter and receiver. When the FCT is turned on, it receives and transmits radio frequency (RF) energy. The system that handles your call when you are using your FCT controls the power level at which your FCT transmits. All Ericsson terminals are designed to not exceed the limits for exposure to RF energy set by national authorities and international health agencies.
Power supply Disposing of the product • Ensure that your AC power outlet is adequately grounded. The product should never be placed in municipal waste. Please check local regulations for disposal of electronic products. • Connect the power supply cord only to the AC power outlet that meet the specifications marked on the FCT power supply. • Never alter the AC power cord or plug. If necessary have the correct outlet installed by a qualified electrician or call your service provider for assistance.
• Do not expose the battery to extreme temperatures, never above +60°C. For maximum battery capacity, use the battery in room temperature. • Do not let the metal contacts on the battery touch another metal object. This could short-circuit and damage the battery. • Do not expose the battery to open flames. This could cause the battery to explode. • Do not expose the battery to liquid. • Do not allow the battery to be put into the mouth. Battery electrolytes may be toxic if swallowed.
Limited Warranty Limited warranty conditions Thank you for purchasing this Ericsson Product. To get the maximum use out of your new product, we recommend that you follow a few simple steps: • Read the Guidelines for safe and efficient use. • Read all of the terms and conditions of the Ericsson Warranty listed below. • Save your original receipt, which is necessary for warranty repair claims.
2. Any repair or replaced Product will be warranted for the remainder of the original warranty period. Repair or replacement may be via functionally equivalent reconditioned units. Replaced faulty parts or components will become the property of Ericsson. 3.
Regulatory information Declaration of Conformity We, Ericsson Radio Systems AB of Kistagången 26, Kista S-16480 Stockholm, Sweden declare under our sole responsibility that our product Ericsson type 0130101-BV and in combination with our accessories, to which this declaration relates is in conformity with the appropriate standards 3GPP TS 51.
Definitions The following definitions are supplied in order to better understand certain concepts included in this manual: Switch-on: power up the FCT by connecting the AC power supply or a charged battery. Switch-off: power down the FCT by disconnecting the AC power supply or removing the battery. Fixed Line Devices: any analog devices that can be connected to the analog fixed line: • Fixed Telephones- ordinary telephones for the fixed line. • G3 Faxes- ordinary fax machines available on the market.
PUK: Personal Unblocking Key. This is the number you get from your network operator and which is used to unblock your SIM card if an incorrect PIN has been entered three times in a row. SIM card: this is the card provided by your network operator that you need to insert in your GSM terminal in order to make and receive calls. It contains all the information from your subscription characteristics.
Visit us on our web site: http://www.ericsson.com/wireless/products/fixed www.westlake.co.uk 0800 298 8011 Ericsson España, S. A.
