Reference Manual
Table Of Contents
- FBTEST Reference Manual
- 1 Introduction
- 2 Installation Procedures
- 3 Hardware, Equipment and Preparation
- 4 FBTEST User Modes
- 5 User Interface Description
- 6 Main Menu
- 6.1 Board Test Menu
- 6.1.1 Alt. 1: Do the Test
- 6.1.2 Alt. 2: Number of Test Cycles
- 6.1.3 Alt. 3: Select/Unselect Boards
- 6.1.4 Alt. 4: Select Extended Test
- 6.1.5 Alt. 5: Select Medium Test
- 6.1.6 Alt. 6: Unselect all Tests
- 6.1.7 Alt. 7-11: Sets the Test Parameters for Each Board
- 6.1.8 Alt.7: Set Parameters for FCB–FE Computer Board
- 6.1.9 Alt. 8: Set Parameters for FRB–FE Radio Board
- 6.1.10 Alt. 9: Set Parameters for FNB–FE Connection Board (BRU3 only)
- 6.1.11 Alt. 10 (BRU3): Set Parameters for FMB–FE Modem Board
- 6.1.12 Alt. 10 (BRU1): Set Parameters for FIB - FE Interface Board
- 6.1.13 Alt. 11: Set Params for FPB–FE Power Supply Board (BRU3 only)
- 6.1.14 Alt.12: Look at Test Results
- 6.2 Set Time
- 6.3 Radio Operations
- 6.4 Measurement Setup Menu
- 6.4.1 Transceiver Control and Presentation Menu
- 6.4.2 Radio Calibration Menu
- 6.4.3 Bandgap Calibration
- 6.4.4 Temperature Sensor Calibration
- 6.4.5 Reference Oscillator OCXO Calibration
- 6.4.6 PF Output Power Calibration
- 6.4.7 PR Reflected Power Calibration
- 6.4.8 VCO Modulation Calibration
- 6.4.9 TCXO Modulation Calibration
- 6.4.10 RSSI Calibration
- 6.4.11 EEPROM Display Editor Menu
- 6.4.12 PA Bias and FDAC Calibration Menu
- 6.4.13 Radio Register Editor Menu
- 6.4.14 Adjustment
- 6.4.15 Setup
- 6.5 Modem Operation Menu (BRU3 only)
- 6.6 Interface Board Parameters Menu (BRU1 only)
- 6.7 Status Overview Menu
- 6.8 Edit Loader Parameters Menu (BRU3 and System Release R14 only)
- 6.1 Board Test Menu
60 (110) BRU1/BRU3 MANUAL
BRU1/BRU3 MANUAL, Doc.no: b3fb_ref Uen Rev PJ5, 2004-02-19
[Main menu, Radio Operations, Calibration, PF Power Calibration]
Figure 30 PF Power Calibration menu.
Alt. 1 ENTER TX POWER OR PF INDEX P1-P8 FOR OFFSET/
ABSOLUTE MODE
Displays SELECT TX_POWER = -21.0 PRESS Y TO SELECT N
TO NEXT
[-21.0 (def), -18.0, -15.0, -12.0, -9.0, -6.0, -3.0, 0.0]
PF Power Calibration SYS:yyyy-mm-dd hh:mm
Current test selection is MEDIUM
TX: OFF TXCH: 3840 PF: 0 TXSEND:OFF RXCH: 3040
PF. INDEX: 2 TEMP INDEX: 2
T1 T2 T3 T4 T5
TDEG -8.0 6.0 20.0 34.0 48.0
PFNUM: 108 107 107 107 106
PFM: 128 126 124 121 117
12 3 45678
PFSET: -21.0 -18.0 -15.0 -12.0 -9.0 -6.0 -3.0 0.0
PFNUM: 101 107 117 128 141 157 177 201
PFM 118 126 137 150 167 186 211 237
1 ENTER TX POWER OR PF INDEX P1-P8 FOR OFFSET/ABSOLUTE MODE
2 ENTER TEMPERATURE INDEX FOR PF IN OFFSET/ABSOLUTE MODE
3 INCREMENT 4 DECREMENT 5 SET VALUE 6 MARK FOR EEPROM
7 - SELECT TRANSMITTER ON/OFF
0. Calibration Menu
Choose alternative: