Reference Manual
Table Of Contents
- FBTEST Reference Manual
- 1 Introduction
- 2 Installation Procedures
- 3 Hardware, Equipment and Preparation
- 4 FBTEST User Modes
- 5 User Interface Description
- 6 Main Menu
- 6.1 Board Test Menu
- 6.1.1 Alt. 1: Do the Test
- 6.1.2 Alt. 2: Number of Test Cycles
- 6.1.3 Alt. 3: Select/Unselect Boards
- 6.1.4 Alt. 4: Select Extended Test
- 6.1.5 Alt. 5: Select Medium Test
- 6.1.6 Alt. 6: Unselect all Tests
- 6.1.7 Alt. 7-11: Sets the Test Parameters for Each Board
- 6.1.8 Alt.7: Set Parameters for FCB–FE Computer Board
- 6.1.9 Alt. 8: Set Parameters for FRB–FE Radio Board
- 6.1.10 Alt. 9: Set Parameters for FNB–FE Connection Board (BRU3 only)
- 6.1.11 Alt. 10 (BRU3): Set Parameters for FMB–FE Modem Board
- 6.1.12 Alt. 10 (BRU1): Set Parameters for FIB - FE Interface Board
- 6.1.13 Alt. 11: Set Params for FPB–FE Power Supply Board (BRU3 only)
- 6.1.14 Alt.12: Look at Test Results
- 6.2 Set Time
- 6.3 Radio Operations
- 6.4 Measurement Setup Menu
- 6.4.1 Transceiver Control and Presentation Menu
- 6.4.2 Radio Calibration Menu
- 6.4.3 Bandgap Calibration
- 6.4.4 Temperature Sensor Calibration
- 6.4.5 Reference Oscillator OCXO Calibration
- 6.4.6 PF Output Power Calibration
- 6.4.7 PR Reflected Power Calibration
- 6.4.8 VCO Modulation Calibration
- 6.4.9 TCXO Modulation Calibration
- 6.4.10 RSSI Calibration
- 6.4.11 EEPROM Display Editor Menu
- 6.4.12 PA Bias and FDAC Calibration Menu
- 6.4.13 Radio Register Editor Menu
- 6.4.14 Adjustment
- 6.4.15 Setup
- 6.5 Modem Operation Menu (BRU3 only)
- 6.6 Interface Board Parameters Menu (BRU1 only)
- 6.7 Status Overview Menu
- 6.8 Edit Loader Parameters Menu (BRU3 and System Release R14 only)
- 6.1 Board Test Menu
12 (110) BRU1/BRU3 MANUAL
BRU1/BRU3 MANUAL, Doc.no: b3fb_ref Uen Rev PJ5, 2004-02-19
3.2 External Tests requiring External Hardware
Some of the external tests require external hardware. The external tests in
question are:
• Loopback Test of FNB Board
• Loopback Test of Ethernet in FIB Board (BRU1 only)
• RFTL Test of FRB Board
• Modem Tests (BRU3 only)
A Loopback test is carried out of the FNB Board by using a 25 pin D-Sub plug.
One of the physical ports is selected according to strapping alternative RS232
or RS422.
For the BRU1, the corresponding serial interfaces are tested when testing the
FIB board.
Also for BRU1, a loopback test of Ethernet in FIB Board is carried out, using
the external ethernet plug.
An RFTL test is carried out of the FRB Board by using an external radio
instrument. A predefined bit stream (Tx-signal) is transmitted from the node to
the RFTL-adapted instrument, where the signal is measured and retransmitted
as an RX-signal back to the node. A bit error count is carried out by comparing
the signals.
One modem test is carried out requiring a test modem and a connection cable to
the node’s line port. Applicable to BRU3 only.
3.3 Start of FBTEST
At the BOOT command prompt “CMD>”, type TE and then press <RETURN>.
The FBTEST program will be loaded and the Main Menu will be displayed
ready to accept commands from the user.
To execute the command frame mode of FBTEST, set the SW2 dip switch on
the FCB-board in the following position: SW2:4 (OEM-Strap) to Open. For
more information, see Node Hardware Library/BRU3/BRU3 Mechanical
Design/FB Computer Board - FCB and BRU3/BRU3 Logic and Radio System/
Modem Equipment. For BRU1 information, see corresponding documents in