Reference Manual
Table Of Contents
- FBTEST Reference Manual
- 1 Introduction
- 2 Installation Procedures
- 3 Hardware, Equipment and Preparation
- 4 FBTEST User Modes
- 5 User Interface Description
- 6 Main Menu
- 6.1 Board Test Menu
- 6.1.1 Alt. 1: Do the Test
- 6.1.2 Alt. 2: Number of Test Cycles
- 6.1.3 Alt. 3: Select/Unselect Boards
- 6.1.4 Alt. 4: Select Extended Test
- 6.1.5 Alt. 5: Select Medium Test
- 6.1.6 Alt. 6: Unselect all Tests
- 6.1.7 Alt. 7-11: Sets the Test Parameters for Each Board
- 6.1.8 Alt.7: Set Parameters for FCB–FE Computer Board
- 6.1.9 Alt. 8: Set Parameters for FRB–FE Radio Board
- 6.1.10 Alt. 9: Set Parameters for FNB–FE Connection Board (BRU3 only)
- 6.1.11 Alt. 10 (BRU3): Set Parameters for FMB–FE Modem Board
- 6.1.12 Alt. 10 (BRU1): Set Parameters for FIB - FE Interface Board
- 6.1.13 Alt. 11: Set Params for FPB–FE Power Supply Board (BRU3 only)
- 6.1.14 Alt.12: Look at Test Results
- 6.2 Set Time
- 6.3 Radio Operations
- 6.4 Measurement Setup Menu
- 6.4.1 Transceiver Control and Presentation Menu
- 6.4.2 Radio Calibration Menu
- 6.4.3 Bandgap Calibration
- 6.4.4 Temperature Sensor Calibration
- 6.4.5 Reference Oscillator OCXO Calibration
- 6.4.6 PF Output Power Calibration
- 6.4.7 PR Reflected Power Calibration
- 6.4.8 VCO Modulation Calibration
- 6.4.9 TCXO Modulation Calibration
- 6.4.10 RSSI Calibration
- 6.4.11 EEPROM Display Editor Menu
- 6.4.12 PA Bias and FDAC Calibration Menu
- 6.4.13 Radio Register Editor Menu
- 6.4.14 Adjustment
- 6.4.15 Setup
- 6.5 Modem Operation Menu (BRU3 only)
- 6.6 Interface Board Parameters Menu (BRU1 only)
- 6.7 Status Overview Menu
- 6.8 Edit Loader Parameters Menu (BRU3 and System Release R14 only)
- 6.1 Board Test Menu
FBTEST REFERENCE MANUAL 101 (110)
BRU1/BRU3 MANUAL, Doc.no: b3fb_ref Uen Rev PJ5, 2004-02-19
[Main menu, Edit Loader Parameters, Ports, X.25 Parameters]
Figure 58 Edit X.25 Parameters menu.
Alt 1. Enter the LOCAL ADDRESS:
Enter your own X.25 address.
Alt 2. Enter the PACKET SIZE [-1 - 512]:(512)
Alt 3. Enter the WINDOW SIZE [-1 - 7]:(2)
Alt 4. Enter the bit rate, a toggle function between 1200 bps, 2400, 4800,
9600, 14400, 19200, 48000, 56000, 64000 bps, External 115 and
External 114. Default External 115.
Alt 5. Enter the Ltc channel [0 - 255]:(1), 2 if PVC
Alt 6. Enter the Htc channel [0 - 255]:(8), Normally 8
Alt 7. A toggle function between X.25 Network or No Network.
Alt 8. Enter the Network ID [0 - 9999]:(255) the X.25 ID if X.25 Network.
X25 parameters for port 1 SYS:yyyy-mm-dd hh:mm
Current test selection is MEDIUM
1 Local address : 1
2 Packet size : 512
3 Window size : 2
4 Bitrate : 9600 bps
5 Ltc channel : 1
6 Htc channel : 8
7 Network : X25 Network
8 Network ID : 255
0. Previous menu
Choose alternative: