Reference Manual
Table Of Contents
- RBS 2206 Reference Manual
- Contents
- Preface
- Product Safety Requirements RBS 2000
- Environmental Capabilities
- Scope
- Terminology
- References
- Transport -40 C - +70 C
- Storage -25 C - +55 C
- Handling -40 C - +70 C
- Operation Indoor +5 C - +40 C
- Operation Outdoor -33 C - +40 C
- Operation Outdoor -33 C - +45 C
- Operation Outdoor -33 C - +55 C
- Operation Mast Mounted Equipment -33 C - +45 C
- Operation Mast Mounted Equipment -33 C - +55 C
- Radio Configurations, RBS 2206
- Product Data
- Unit Description, DXU-21
- Unit Description, dTRU
- Unit Decription, CDU-G and CDU-F
- Unit Description, CXU-10
- Unit Description, FCU-01
- Unit Description, DC-Filter 01
- Unit Description, PSU 1200 W
- Unit Description, ACCU/DCCU
- Unit Description, IDM
- Broadcast
- Common Control Channel Handling
- Physical Channel Handling
- Speech and Data Services
- Packet Data Services
- Call Control
- References
- Channel Activation
- Adaptive Frame Alignment
- Asynchronous Handover Detection
- RF Channel Release
- Deactivate SACCH
- Link Establish Indication
- Link Release Indication
- Link Establishment Request
- Link Release Request
- Transparent Message Transmission
- Transparent Message Reception
- SACCH Info Modify
- LAPDm
- Channel Reactivation
- Power Information
- GPRS, Physical Link Layer
- Base Station Power Control
- Channel Measurements
- Discontinuous Transmission
- Frequency Hopping
- Encryption
- Mode Modify
- Mobile Station Power Control
- Short Message Service
- Diversity Supervision
- Synchronization
- Radio Reception
- Radio Transmission
- Frequency Allocation Support
- Restart and Recovery
- Function Change
- Functionality Administration
- Operation and Maintenance Support
- References
- Concepts
- Buttons
- Change RU to Local Mode
- Change RU to Remote Mode
- Change RU to Remote Mode Cancel
- Change SW Power Boost Slave RU to Local Mode
- Loop Control
- RF Loop Test Supervision
- Calendar Time Request
- RSSI Temperature Compensation
- Max Cooling
- Fault Indicator
- BS Fault Indicator
- Operational Indicator
- Tx Not Enabled Indicator
- Local Mode Indicator
- External Alarms Indicator
- DC Disconnected Indicator
- Battery Mode Indicator
- Bat Disconnected Indicator
- AC Fault Indicator
- Test Result Indicators (not used)
- Local Mode in Progress
- Installation Data Handling
- Self Test and Supervision
- Diagnostics and Fault Handling
- Operation and Maintenance Terminal
- External Alarms
- Handling of Auxiliary Equipment
- Climate Protection
- EMC Capabilities
- Transmission Interface Handling G.703 2048 kbit/s
- Transmission Interface Handling DS1 1544 kbit/s
- Terrestrial Link Handling
- Channel Distribution Function
- Transport network O&M functions-DXX Support
- BTS Parameter Limitations
- Glossary
Radio Configurations, RBS 2206
4.8 Co-Siting with RBS 200 or RBS 2000 Macro Cabinet
This section shows expansions where RBSs, forming an original SCC,
are co-sited and use TG-synchronization to form one new resulting
SCC. Antennas are not shared.
4.8.1 RBS 200 Expanded with 12–TRX Cabinet
Co-Siting with RBS 200 Using a Filter Combiner
Using TG-synchronization, it is possible to build one resulting SCC
from the described SCC in the table below. The antenna systems are
not shared between RBSs.
Table 33 Expansion using filter combiner
Result
SCC
Original
SCC
Cabinet Combiner Antennas TMA Original
SCC
Basic
Configuration
Antennas
1 x 16 *
1x4 RBS 200 FCOMB (3) No 1x12 F9de_2.12 (2)
RBS 205 FCOMB (3) No F18d_2.12 (2)
RBS 205 FCOMB (3) M F18dt_2.12 (2)
RBS 205 FCOMB&DPX (2) No F18d_2.12 (2)
RBS 205 FCOMB (2) M F18dt_2.12 (2)
1x20
**
1x8 RBS 200 FCOMB (3) No 1x12 F9de_2.12 (2)
RBS 205 FCOMB (3) No F18d_2.12 (2)
RBS 205 FCOMB (3) M F18dt_2.12 (2)
RBS 205 FCOMB&DPX (2) No F18d_2.12 (2)
RBS 205 FCOMB (2) M F18dt_2.12 (2)
3x8
***
3x4 RBS 200 FCOMB (3) (3) (3) No 3x4 3 x F9de_2.4 (2) (2) (2)
**** RBS 205 FCOMB (3) (3) (3) No 3 x F18d_2.4 (2) (2) (2)
RBS 205 FCOMB (3) (3) (3) M 3 x F18dt_2.4 (2) (2) (2)
RBS 205 FCOMB&DPX (2) (2) (2) No 3 x F18d_2.4 (2) (2) (2)
RBS 205 FCOMB (2) (2) (2) M 3 x F18dt_2.4 (2) (2) (2)
M = Mandatory
* 1 x 6, 1 x 8, 1 x 10, 1 x 12 and 1 x 14 can be accomplished with a
partly-equipped expansion configuration.
** 1 x 10, 1 x 12, 1 x 14, 1 x 16 and 1 x 18 can be accomplished with
a partly-equipped expansion configuration.
*** 3 x 6 can be accomplished with a partly-equipped expansion
configuration.
**** When using TG-synchronization, only one RBS 200/RBS 205 can
act as master. Therefore the 3 x 4 configuration, which is three separate
RBSs, must be rebuilt to one single RBS, that is, all three sectors of the
RBS 200 must be connected to the same TMCB.
74 (421)
EN/LZT 720 0008 R1A
2001-06-26
© Ericsson Radio Systems AB
— All Rights Reserved —