Reference Manual
Table Of Contents
- RBS 2206 Reference Manual
- Contents
- Preface
- Product Safety Requirements RBS 2000
- Environmental Capabilities
- Scope
- Terminology
- References
- Transport -40 C - +70 C
- Storage -25 C - +55 C
- Handling -40 C - +70 C
- Operation Indoor +5 C - +40 C
- Operation Outdoor -33 C - +40 C
- Operation Outdoor -33 C - +45 C
- Operation Outdoor -33 C - +55 C
- Operation Mast Mounted Equipment -33 C - +45 C
- Operation Mast Mounted Equipment -33 C - +55 C
- Radio Configurations, RBS 2206
- Product Data
- Unit Description, DXU-21
- Unit Description, dTRU
- Unit Decription, CDU-G and CDU-F
- Unit Description, CXU-10
- Unit Description, FCU-01
- Unit Description, DC-Filter 01
- Unit Description, PSU 1200 W
- Unit Description, ACCU/DCCU
- Unit Description, IDM
- Broadcast
- Common Control Channel Handling
- Physical Channel Handling
- Speech and Data Services
- Packet Data Services
- Call Control
- References
- Channel Activation
- Adaptive Frame Alignment
- Asynchronous Handover Detection
- RF Channel Release
- Deactivate SACCH
- Link Establish Indication
- Link Release Indication
- Link Establishment Request
- Link Release Request
- Transparent Message Transmission
- Transparent Message Reception
- SACCH Info Modify
- LAPDm
- Channel Reactivation
- Power Information
- GPRS, Physical Link Layer
- Base Station Power Control
- Channel Measurements
- Discontinuous Transmission
- Frequency Hopping
- Encryption
- Mode Modify
- Mobile Station Power Control
- Short Message Service
- Diversity Supervision
- Synchronization
- Radio Reception
- Radio Transmission
- Frequency Allocation Support
- Restart and Recovery
- Function Change
- Functionality Administration
- Operation and Maintenance Support
- References
- Concepts
- Buttons
- Change RU to Local Mode
- Change RU to Remote Mode
- Change RU to Remote Mode Cancel
- Change SW Power Boost Slave RU to Local Mode
- Loop Control
- RF Loop Test Supervision
- Calendar Time Request
- RSSI Temperature Compensation
- Max Cooling
- Fault Indicator
- BS Fault Indicator
- Operational Indicator
- Tx Not Enabled Indicator
- Local Mode Indicator
- External Alarms Indicator
- DC Disconnected Indicator
- Battery Mode Indicator
- Bat Disconnected Indicator
- AC Fault Indicator
- Test Result Indicators (not used)
- Local Mode in Progress
- Installation Data Handling
- Self Test and Supervision
- Diagnostics and Fault Handling
- Operation and Maintenance Terminal
- External Alarms
- Handling of Auxiliary Equipment
- Climate Protection
- EMC Capabilities
- Transmission Interface Handling G.703 2048 kbit/s
- Transmission Interface Handling DS1 1544 kbit/s
- Terrestrial Link Handling
- Channel Distribution Function
- Transport network O&M functions-DXX Support
- BTS Parameter Limitations
- Glossary
BTS Parameter Limitations
52 BTS Parameter Limitations
This document specifies configurable BTS parameters with limitations
compared with the parameter ranges in the Abis O&M IWD. BTS
parameters with no limitations compared to the Abis O&M IWD are not
stated in this document.
52.1 Purpose and Readers
The purpose is to show BTS parameters with parameter range
limitations compared to the Abis O&M IWD.
People involved in the preparation of data transcripts for the BSC are
the target group of this specification.
52.2 References
•
6/155 19–HSC 103 12 Uen
Abis O&M Interface, Part II, Procedures
• 5/155 19–HSC 103 12 Uen
Abis O&M Interface, Part I, Model
•
3/1551–APT 210 09 Uen
Translation of Abis O&M IWD Parameters - BSC Command
Parameters
52.3 Parameters
The parameters listed in this document are extracted from the Data
Elements listed in the Abis O&M IWD document (see reference 1).
This document states the BTS parameters with parameter range
limitations compared with the Abis O&M IWD.
For each parameter in the list, the range supported by the BTS and the
Abis O&M IWD is stated.
All coding in the document is in hexadecimal (hex) representation if
nothing else is stated.
Note: See reference 3 for BSC Commands.
52.3.1 Accordance Indication
BTS-supported value range:
AIP: 0 – 1, 3
IWD-defined value range: 0 – 3
52.3.2 Alarm Status Type
BTS-supported value range:
Alarm status type: 1
IWD
EN/LZT 720 0008 R1A
2001-06-26
399 (421)
© Ericsson Radio Systems AB
— All Rights Reserved —