Reference Manual
Table Of Contents
- RBS 2206 Reference Manual
- Contents
- Preface
- Product Safety Requirements RBS 2000
- Environmental Capabilities
- Scope
- Terminology
- References
- Transport -40 C - +70 C
- Storage -25 C - +55 C
- Handling -40 C - +70 C
- Operation Indoor +5 C - +40 C
- Operation Outdoor -33 C - +40 C
- Operation Outdoor -33 C - +45 C
- Operation Outdoor -33 C - +55 C
- Operation Mast Mounted Equipment -33 C - +45 C
- Operation Mast Mounted Equipment -33 C - +55 C
- Radio Configurations, RBS 2206
- Product Data
- Unit Description, DXU-21
- Unit Description, dTRU
- Unit Decription, CDU-G and CDU-F
- Unit Description, CXU-10
- Unit Description, FCU-01
- Unit Description, DC-Filter 01
- Unit Description, PSU 1200 W
- Unit Description, ACCU/DCCU
- Unit Description, IDM
- Broadcast
- Common Control Channel Handling
- Physical Channel Handling
- Speech and Data Services
- Packet Data Services
- Call Control
- References
- Channel Activation
- Adaptive Frame Alignment
- Asynchronous Handover Detection
- RF Channel Release
- Deactivate SACCH
- Link Establish Indication
- Link Release Indication
- Link Establishment Request
- Link Release Request
- Transparent Message Transmission
- Transparent Message Reception
- SACCH Info Modify
- LAPDm
- Channel Reactivation
- Power Information
- GPRS, Physical Link Layer
- Base Station Power Control
- Channel Measurements
- Discontinuous Transmission
- Frequency Hopping
- Encryption
- Mode Modify
- Mobile Station Power Control
- Short Message Service
- Diversity Supervision
- Synchronization
- Radio Reception
- Radio Transmission
- Frequency Allocation Support
- Restart and Recovery
- Function Change
- Functionality Administration
- Operation and Maintenance Support
- References
- Concepts
- Buttons
- Change RU to Local Mode
- Change RU to Remote Mode
- Change RU to Remote Mode Cancel
- Change SW Power Boost Slave RU to Local Mode
- Loop Control
- RF Loop Test Supervision
- Calendar Time Request
- RSSI Temperature Compensation
- Max Cooling
- Fault Indicator
- BS Fault Indicator
- Operational Indicator
- Tx Not Enabled Indicator
- Local Mode Indicator
- External Alarms Indicator
- DC Disconnected Indicator
- Battery Mode Indicator
- Bat Disconnected Indicator
- AC Fault Indicator
- Test Result Indicators (not used)
- Local Mode in Progress
- Installation Data Handling
- Self Test and Supervision
- Diagnostics and Fault Handling
- Operation and Maintenance Terminal
- External Alarms
- Handling of Auxiliary Equipment
- Climate Protection
- EMC Capabilities
- Transmission Interface Handling G.703 2048 kbit/s
- Transmission Interface Handling DS1 1544 kbit/s
- Terrestrial Link Handling
- Channel Distribution Function
- Transport network O&M functions-DXX Support
- BTS Parameter Limitations
- Glossary
Transport network O&M functions-DXX Support
TNOM timeslotThe parameter used for the Transport Network O&M
Timeslot allocation is:TNOM_timeslot
The valid range of the parameter is:1–31 for E11–24 for T1
TNOM node IdThe parameter used for the Transport Network O&M
Node Id allocation is:TNOM_nodeid
The valid range of the parameter is:1–65534
The parameters can be modified from the OMT. The parameter
TNOM_nodeid can be modified from DXX as well. The new settings
are activated immediately.
51.4.13 Administration of DXX specific functions
The DXX specific functions are maintained via the interface
’RBS2000–DXX O&M’.
Application Parameters
The parameters used for the Node identity function are handled
by:Object 50 (SUBRACK_INVENTORY)
The parameters used for the Node access control are handled by:Object
44 (NAC_OBJECT)
The parameters used for the Real time control function are handled
by:Object 44 (RTC_OBJECT)
The parameters used for the Current alarm report are handled by:Object
6 (CURRENT _ALARMS)Object 40 (SUBRACK_STATE)Object 41
(NODE_STATE)
The parameters used for the Alarm history report are handled by:Object
7 (ALARM_HISTORY)
The parameters used for the G.821 performance report are handled
by:Object 23 (G.821_OBJECT)
The parameters used for the Fault mask function are handled by:Object
27 (FLM_OBJECT)Object 228 (IFM_OBJECT)
The parameters used for the Loop back function are handled by:Object
227 (LL_OBJECT)Object 226 (CONTROLS_TIMEOUT)
The parameters used for the Node inventory function are handled
by:Object 2 (UNIT_IDENT)Object 17
(INTERFACE_LOCKING)Object 18 (INTERFACE_MODULE)Object
50 (SUBRACK_INVENTORY)Object 230 (HDLC_MODE)Object 240
(TS0B4..B8_OBJECT)Object 243 (TS0B1_OBJECT)
51.4.14 DXX Protocol Handling
This function is initiated during restart of the DXU if the parameter
TNOM_use in RBS DB is already set to ON, otherwise the function is
initiated when the parameter is set to ON.
The DXX protocol is implemented as four layers in the ISO OSI layer
model, layer 1,2,3 and 7. These layers correspond to physical link
layer, data link layer, network layer, and application layer respectively.
EN/LZT 720 0008 R1A
2001-06-26
397 (421)
© Ericsson Radio Systems AB
— All Rights Reserved —