Reference Manual
Table Of Contents
- RBS 2206 Reference Manual
- Contents
- Preface
- Product Safety Requirements RBS 2000
- Environmental Capabilities
- Scope
- Terminology
- References
- Transport -40 C - +70 C
- Storage -25 C - +55 C
- Handling -40 C - +70 C
- Operation Indoor +5 C - +40 C
- Operation Outdoor -33 C - +40 C
- Operation Outdoor -33 C - +45 C
- Operation Outdoor -33 C - +55 C
- Operation Mast Mounted Equipment -33 C - +45 C
- Operation Mast Mounted Equipment -33 C - +55 C
- Radio Configurations, RBS 2206
- Product Data
- Unit Description, DXU-21
- Unit Description, dTRU
- Unit Decription, CDU-G and CDU-F
- Unit Description, CXU-10
- Unit Description, FCU-01
- Unit Description, DC-Filter 01
- Unit Description, PSU 1200 W
- Unit Description, ACCU/DCCU
- Unit Description, IDM
- Broadcast
- Common Control Channel Handling
- Physical Channel Handling
- Speech and Data Services
- Packet Data Services
- Call Control
- References
- Channel Activation
- Adaptive Frame Alignment
- Asynchronous Handover Detection
- RF Channel Release
- Deactivate SACCH
- Link Establish Indication
- Link Release Indication
- Link Establishment Request
- Link Release Request
- Transparent Message Transmission
- Transparent Message Reception
- SACCH Info Modify
- LAPDm
- Channel Reactivation
- Power Information
- GPRS, Physical Link Layer
- Base Station Power Control
- Channel Measurements
- Discontinuous Transmission
- Frequency Hopping
- Encryption
- Mode Modify
- Mobile Station Power Control
- Short Message Service
- Diversity Supervision
- Synchronization
- Radio Reception
- Radio Transmission
- Frequency Allocation Support
- Restart and Recovery
- Function Change
- Functionality Administration
- Operation and Maintenance Support
- References
- Concepts
- Buttons
- Change RU to Local Mode
- Change RU to Remote Mode
- Change RU to Remote Mode Cancel
- Change SW Power Boost Slave RU to Local Mode
- Loop Control
- RF Loop Test Supervision
- Calendar Time Request
- RSSI Temperature Compensation
- Max Cooling
- Fault Indicator
- BS Fault Indicator
- Operational Indicator
- Tx Not Enabled Indicator
- Local Mode Indicator
- External Alarms Indicator
- DC Disconnected Indicator
- Battery Mode Indicator
- Bat Disconnected Indicator
- AC Fault Indicator
- Test Result Indicators (not used)
- Local Mode in Progress
- Installation Data Handling
- Self Test and Supervision
- Diagnostics and Fault Handling
- Operation and Maintenance Terminal
- External Alarms
- Handling of Auxiliary Equipment
- Climate Protection
- EMC Capabilities
- Transmission Interface Handling G.703 2048 kbit/s
- Transmission Interface Handling DS1 1544 kbit/s
- Terrestrial Link Handling
- Channel Distribution Function
- Transport network O&M functions-DXX Support
- BTS Parameter Limitations
- Glossary
Operation and Maintenance Terminal
Exception: A DXU which uses the PRACT transmission circuit
does not support the LBO values.
•
Modify FDL use values for transmission interface.
Sets the individual Facility Data Link (FDL) use values for a T1
transmission interface. The values are defined and referred as
parameter "FDL_use" in the IDB.
Exception: A DXU which uses the PRACT transmission circuit
does not support the FDL_use.
•
Display FDL use values for transmission interface.
Displays the individual FDL use values for a T1 transmission
interface. The values are defined and stored as parameter
"FDL_use" in the IDB.
Exception: A DXU which uses the PRACT transmission circuit
does not support the FDL_use.
The functions above are normally used at:
•
Installation (set transmission interface type, set/display available
synchronization source, display/define spare bits, display/switch
on/switch off CRC-4)
•
Maintenance (monitor maintenance data)
42.3.13 Antenna System
The following user functions, related to the antenna system, are
available in the OMT:
•
Monitor maintenance data, display any of the following data and
update changes continuously
− Diversity
The functions above are normally used for maintenance.
42.3.14 Transceiver
The following user functions, related to the transceivers, are available in
the OMT:
•
Switch on QIU, switch on subjective speech quality improvements
uplink for one or more traffic channels within one transceiver
1)
• Switch off QIU
1)
1)
Facilitates BER measurements according to /GSM:11.20/ and /
GSM:05.05/.
• Monitor maintenance data, display any of the following data and
update changes continuously
− Transmission and reception
− Timing advance
328 (421)
EN/LZT 720 0008 R1A
2001-06-26
© Ericsson Radio Systems AB
— All Rights Reserved —