Reference Manual
Table Of Contents
- RBS 2206 Reference Manual
- Contents
- Preface
- Product Safety Requirements RBS 2000
- Environmental Capabilities
- Scope
- Terminology
- References
- Transport -40 C - +70 C
- Storage -25 C - +55 C
- Handling -40 C - +70 C
- Operation Indoor +5 C - +40 C
- Operation Outdoor -33 C - +40 C
- Operation Outdoor -33 C - +45 C
- Operation Outdoor -33 C - +55 C
- Operation Mast Mounted Equipment -33 C - +45 C
- Operation Mast Mounted Equipment -33 C - +55 C
- Radio Configurations, RBS 2206
- Product Data
- Unit Description, DXU-21
- Unit Description, dTRU
- Unit Decription, CDU-G and CDU-F
- Unit Description, CXU-10
- Unit Description, FCU-01
- Unit Description, DC-Filter 01
- Unit Description, PSU 1200 W
- Unit Description, ACCU/DCCU
- Unit Description, IDM
- Broadcast
- Common Control Channel Handling
- Physical Channel Handling
- Speech and Data Services
- Packet Data Services
- Call Control
- References
- Channel Activation
- Adaptive Frame Alignment
- Asynchronous Handover Detection
- RF Channel Release
- Deactivate SACCH
- Link Establish Indication
- Link Release Indication
- Link Establishment Request
- Link Release Request
- Transparent Message Transmission
- Transparent Message Reception
- SACCH Info Modify
- LAPDm
- Channel Reactivation
- Power Information
- GPRS, Physical Link Layer
- Base Station Power Control
- Channel Measurements
- Discontinuous Transmission
- Frequency Hopping
- Encryption
- Mode Modify
- Mobile Station Power Control
- Short Message Service
- Diversity Supervision
- Synchronization
- Radio Reception
- Radio Transmission
- Frequency Allocation Support
- Restart and Recovery
- Function Change
- Functionality Administration
- Operation and Maintenance Support
- References
- Concepts
- Buttons
- Change RU to Local Mode
- Change RU to Remote Mode
- Change RU to Remote Mode Cancel
- Change SW Power Boost Slave RU to Local Mode
- Loop Control
- RF Loop Test Supervision
- Calendar Time Request
- RSSI Temperature Compensation
- Max Cooling
- Fault Indicator
- BS Fault Indicator
- Operational Indicator
- Tx Not Enabled Indicator
- Local Mode Indicator
- External Alarms Indicator
- DC Disconnected Indicator
- Battery Mode Indicator
- Bat Disconnected Indicator
- AC Fault Indicator
- Test Result Indicators (not used)
- Local Mode in Progress
- Installation Data Handling
- Self Test and Supervision
- Diagnostics and Fault Handling
- Operation and Maintenance Terminal
- External Alarms
- Handling of Auxiliary Equipment
- Climate Protection
- EMC Capabilities
- Transmission Interface Handling G.703 2048 kbit/s
- Transmission Interface Handling DS1 1544 kbit/s
- Terrestrial Link Handling
- Channel Distribution Function
- Transport network O&M functions-DXX Support
- BTS Parameter Limitations
- Glossary
Operation and Maintenance Terminal
42.3.6 ARAE Supervision Parameters
The following user functions, related to the ARAE, are available in the
OMT:
• Auxiliary Faults are possible to define for each alarm inlet.
• The alarm inlets can be used for both External Alarms and for
ARAE Supervision.
•
The definition of the ARAE Supervision Parameters is displayed.
•
Monitor ARAE fault status.
The output can be displayed or directed to file (output stored in a file on
the OMT).
42.3.7 Modify TN O&M Values
This function modifies the Transport Network O&M parameters in the
IDB. There are three TN O&M parameters in the TNOM_information
element that are possible to modify:
TNOM_use. Indicates if TN O&M functionality is activated or not.
TNOM_timeslot. Indicates which 64 kbit/s timeslot on the PCM link to
use for TN O&M communication.
TNOM_nodeid. Holds the identity of the BTS node in the TN O&M
network.
42.3.8 Display TN O&M Values
This function displays the value of the TN O&M parameters, which are
stored in the TNOM_information element in the IDB (see parameters
above).
42.3.9 Calibration of Optional Reference Oscillator
This function is used to calibrate the optional reference oscillator.
42.3.10 Cable Loss
The following user function, related to Cable loss, is available in the
OMT:
• Define cable loss, defines cable and feeder loss values.
• Display cable loss, displays cable and feeder loss values.
42.3.11 ALNA/TMA Parameters
The following functions, related to ALNA/TMA parameters are
available in the OMT.
• Define ALNA/TMA parameters.
In OMT state LOCAL and in OMT state CONNECTED, it is
possible to define values for the following:
– Current Supervision Limits
EN/LZT 720 0008 R1A
2001-06-26
325 (421)
© Ericsson Radio Systems AB
— All Rights Reserved —