Reference Manual
Table Of Contents
- RBS 2206 Reference Manual
- Contents
- Preface
- Product Safety Requirements RBS 2000
- Environmental Capabilities
- Scope
- Terminology
- References
- Transport -40 C - +70 C
- Storage -25 C - +55 C
- Handling -40 C - +70 C
- Operation Indoor +5 C - +40 C
- Operation Outdoor -33 C - +40 C
- Operation Outdoor -33 C - +45 C
- Operation Outdoor -33 C - +55 C
- Operation Mast Mounted Equipment -33 C - +45 C
- Operation Mast Mounted Equipment -33 C - +55 C
- Radio Configurations, RBS 2206
- Product Data
- Unit Description, DXU-21
- Unit Description, dTRU
- Unit Decription, CDU-G and CDU-F
- Unit Description, CXU-10
- Unit Description, FCU-01
- Unit Description, DC-Filter 01
- Unit Description, PSU 1200 W
- Unit Description, ACCU/DCCU
- Unit Description, IDM
- Broadcast
- Common Control Channel Handling
- Physical Channel Handling
- Speech and Data Services
- Packet Data Services
- Call Control
- References
- Channel Activation
- Adaptive Frame Alignment
- Asynchronous Handover Detection
- RF Channel Release
- Deactivate SACCH
- Link Establish Indication
- Link Release Indication
- Link Establishment Request
- Link Release Request
- Transparent Message Transmission
- Transparent Message Reception
- SACCH Info Modify
- LAPDm
- Channel Reactivation
- Power Information
- GPRS, Physical Link Layer
- Base Station Power Control
- Channel Measurements
- Discontinuous Transmission
- Frequency Hopping
- Encryption
- Mode Modify
- Mobile Station Power Control
- Short Message Service
- Diversity Supervision
- Synchronization
- Radio Reception
- Radio Transmission
- Frequency Allocation Support
- Restart and Recovery
- Function Change
- Functionality Administration
- Operation and Maintenance Support
- References
- Concepts
- Buttons
- Change RU to Local Mode
- Change RU to Remote Mode
- Change RU to Remote Mode Cancel
- Change SW Power Boost Slave RU to Local Mode
- Loop Control
- RF Loop Test Supervision
- Calendar Time Request
- RSSI Temperature Compensation
- Max Cooling
- Fault Indicator
- BS Fault Indicator
- Operational Indicator
- Tx Not Enabled Indicator
- Local Mode Indicator
- External Alarms Indicator
- DC Disconnected Indicator
- Battery Mode Indicator
- Bat Disconnected Indicator
- AC Fault Indicator
- Test Result Indicators (not used)
- Local Mode in Progress
- Installation Data Handling
- Self Test and Supervision
- Diagnostics and Fault Handling
- Operation and Maintenance Terminal
- External Alarms
- Handling of Auxiliary Equipment
- Climate Protection
- EMC Capabilities
- Transmission Interface Handling G.703 2048 kbit/s
- Transmission Interface Handling DS1 1544 kbit/s
- Terrestrial Link Handling
- Channel Distribution Function
- Transport network O&M functions-DXX Support
- BTS Parameter Limitations
- Glossary
Operation and Maintenance Terminal
Configurations possible to display, comprise all RBS 2000
products and the configurations as specified for each product.
The following RU and connections are graphically displayed:
−
DXU
− TRU
− ECU
− CDU
− Local bus
− CDU bus
− Number of antenna systems (1 or 3)
• Display RBS software revisions, display RU software revisions for
all Main RUs, see Section 42.3.16 Replaceable Unit on page 329.
•
Display TEI/RU list, display list of TEI and RU Instances for the
CMRU and for the DMRUs with a direct signalling link to the
BSC in the cabinet (see also Section 42.3.16 Replaceable Unit on
page 329).
The functions above are normally used for:
•
General purpose (display RBS configuration)
•
Maintenance (display RBS software revisions)
•
Installation (display TEI/RU list)
42.3.3 OMT Connection
The following user functions, related to the OMT, are available in the
OMT:
• Connect, establish a connection between the OMT and the RBS.
A functionality and compatibility check is performed on RBS and
OMT software versions. If the OMT is connected remotely an
RBS address can be given in order to select one of several RBSes
connected in a multidrop chain. Also a timeslot, which the OMT
uses when established, is given by the operator. The RBS is
scanning for remote OMT link establishment on all 64 kbit/s
timeslots on PCM-A. If the RBS software does not support
scanning for remote OMT link establishment on all timeslots, the
operator has to use TS23, which is the default value. In case of
different versions the OMT operator is informed about this fact
and that all functionality is not supported.
• Disconnect, release the connection between the OMT and the
RBS.
The functions above are for general purpose use.
42.3.4 Installation Database
The following user functions, related to the IDB, are available in the
OMT:
EN/LZT 720 0008 R1A
2001-06-26
323 (421)
© Ericsson Radio Systems AB
— All Rights Reserved —