Reference Manual
Table Of Contents
- RBS 2206 Reference Manual
- Contents
- Preface
- Product Safety Requirements RBS 2000
- Environmental Capabilities
- Scope
- Terminology
- References
- Transport -40 C - +70 C
- Storage -25 C - +55 C
- Handling -40 C - +70 C
- Operation Indoor +5 C - +40 C
- Operation Outdoor -33 C - +40 C
- Operation Outdoor -33 C - +45 C
- Operation Outdoor -33 C - +55 C
- Operation Mast Mounted Equipment -33 C - +45 C
- Operation Mast Mounted Equipment -33 C - +55 C
- Radio Configurations, RBS 2206
- Product Data
- Unit Description, DXU-21
- Unit Description, dTRU
- Unit Decription, CDU-G and CDU-F
- Unit Description, CXU-10
- Unit Description, FCU-01
- Unit Description, DC-Filter 01
- Unit Description, PSU 1200 W
- Unit Description, ACCU/DCCU
- Unit Description, IDM
- Broadcast
- Common Control Channel Handling
- Physical Channel Handling
- Speech and Data Services
- Packet Data Services
- Call Control
- References
- Channel Activation
- Adaptive Frame Alignment
- Asynchronous Handover Detection
- RF Channel Release
- Deactivate SACCH
- Link Establish Indication
- Link Release Indication
- Link Establishment Request
- Link Release Request
- Transparent Message Transmission
- Transparent Message Reception
- SACCH Info Modify
- LAPDm
- Channel Reactivation
- Power Information
- GPRS, Physical Link Layer
- Base Station Power Control
- Channel Measurements
- Discontinuous Transmission
- Frequency Hopping
- Encryption
- Mode Modify
- Mobile Station Power Control
- Short Message Service
- Diversity Supervision
- Synchronization
- Radio Reception
- Radio Transmission
- Frequency Allocation Support
- Restart and Recovery
- Function Change
- Functionality Administration
- Operation and Maintenance Support
- References
- Concepts
- Buttons
- Change RU to Local Mode
- Change RU to Remote Mode
- Change RU to Remote Mode Cancel
- Change SW Power Boost Slave RU to Local Mode
- Loop Control
- RF Loop Test Supervision
- Calendar Time Request
- RSSI Temperature Compensation
- Max Cooling
- Fault Indicator
- BS Fault Indicator
- Operational Indicator
- Tx Not Enabled Indicator
- Local Mode Indicator
- External Alarms Indicator
- DC Disconnected Indicator
- Battery Mode Indicator
- Bat Disconnected Indicator
- AC Fault Indicator
- Test Result Indicators (not used)
- Local Mode in Progress
- Installation Data Handling
- Self Test and Supervision
- Diagnostics and Fault Handling
- Operation and Maintenance Terminal
- External Alarms
- Handling of Auxiliary Equipment
- Climate Protection
- EMC Capabilities
- Transmission Interface Handling G.703 2048 kbit/s
- Transmission Interface Handling DS1 1544 kbit/s
- Terrestrial Link Handling
- Channel Distribution Function
- Transport network O&M functions-DXX Support
- BTS Parameter Limitations
- Glossary
Operation and Maintenance Support
Preconditions and Initiation
Applicable for any operational condition. The function is initiated by
the HW when the RU is started.
Description
The DC Disconnect indicator indicates if the DC is working properly or
not. If the environmental requirements are not fulfilled, the power to the
rest of the RBS is switched off. The DC Disconnect indicator is
controlled from the Climate protection functionality and from Restart
and Recovery functionality. When the RU is reset in any way the
handling of the indicator is terminated.
Colour: Yellow
Position: EDMRU (ECU)
States of the indicator
ON: The environmental requirements are not
fulfilled and thus the power to the rest of
the RBS is switched off.
OFF The environmental requirements are
fulfilled.
38.20 Battery Mode Indicator
Purpose
To indicate if the RBS is running on battery backup.
Preconditions and Initiation
Applicable for any operational condition. The function is initiated by
the HW when the RU is started.
Description
The Battery Mode indicator indicates if the RBS is running on mains
power supply or battery backup. The Battery Mode indicator is
controlled from Power Supply functionality and from Restart and
Recovery functionality. When the RU is reset in any way the handling
of the indicator is terminated.
Colour: Yellow
Position: EDMRU (ECU)
States of the indicator
ON: Battery power supply fully or partly used.
OFF Mains power supply. No battery power is
used.
EN/LZT 720 0008 R1A
2001-06-26
297 (421)
© Ericsson Radio Systems AB
— All Rights Reserved —