Reference Manual
Table Of Contents
- RBS 2206 Reference Manual
- Contents
- Preface
- Product Safety Requirements RBS 2000
- Environmental Capabilities
- Scope
- Terminology
- References
- Transport -40 C - +70 C
- Storage -25 C - +55 C
- Handling -40 C - +70 C
- Operation Indoor +5 C - +40 C
- Operation Outdoor -33 C - +40 C
- Operation Outdoor -33 C - +45 C
- Operation Outdoor -33 C - +55 C
- Operation Mast Mounted Equipment -33 C - +45 C
- Operation Mast Mounted Equipment -33 C - +55 C
- Radio Configurations, RBS 2206
- Product Data
- Unit Description, DXU-21
- Unit Description, dTRU
- Unit Decription, CDU-G and CDU-F
- Unit Description, CXU-10
- Unit Description, FCU-01
- Unit Description, DC-Filter 01
- Unit Description, PSU 1200 W
- Unit Description, ACCU/DCCU
- Unit Description, IDM
- Broadcast
- Common Control Channel Handling
- Physical Channel Handling
- Speech and Data Services
- Packet Data Services
- Call Control
- References
- Channel Activation
- Adaptive Frame Alignment
- Asynchronous Handover Detection
- RF Channel Release
- Deactivate SACCH
- Link Establish Indication
- Link Release Indication
- Link Establishment Request
- Link Release Request
- Transparent Message Transmission
- Transparent Message Reception
- SACCH Info Modify
- LAPDm
- Channel Reactivation
- Power Information
- GPRS, Physical Link Layer
- Base Station Power Control
- Channel Measurements
- Discontinuous Transmission
- Frequency Hopping
- Encryption
- Mode Modify
- Mobile Station Power Control
- Short Message Service
- Diversity Supervision
- Synchronization
- Radio Reception
- Radio Transmission
- Frequency Allocation Support
- Restart and Recovery
- Function Change
- Functionality Administration
- Operation and Maintenance Support
- References
- Concepts
- Buttons
- Change RU to Local Mode
- Change RU to Remote Mode
- Change RU to Remote Mode Cancel
- Change SW Power Boost Slave RU to Local Mode
- Loop Control
- RF Loop Test Supervision
- Calendar Time Request
- RSSI Temperature Compensation
- Max Cooling
- Fault Indicator
- BS Fault Indicator
- Operational Indicator
- Tx Not Enabled Indicator
- Local Mode Indicator
- External Alarms Indicator
- DC Disconnected Indicator
- Battery Mode Indicator
- Bat Disconnected Indicator
- AC Fault Indicator
- Test Result Indicators (not used)
- Local Mode in Progress
- Installation Data Handling
- Self Test and Supervision
- Diagnostics and Fault Handling
- Operation and Maintenance Terminal
- External Alarms
- Handling of Auxiliary Equipment
- Climate Protection
- EMC Capabilities
- Transmission Interface Handling G.703 2048 kbit/s
- Transmission Interface Handling DS1 1544 kbit/s
- Terrestrial Link Handling
- Channel Distribution Function
- Transport network O&M functions-DXX Support
- BTS Parameter Limitations
- Glossary
Operation and Maintenance Support
Preconditions and Initiation
Applicable for any operational condition. The function is initiated when
the SW is started.
Description
The TX Not Enabled indicator is controlled from Functionality
Administration functionality and from Restart and Recovery
functionality. The TX Not Enabled indicator is on until the BSC has
changed MO State for TX to enabled. When the TX is disabled or reset
by the BSC or auto-disabled by the RBS the indicator is turned on.
When the RU is reset in any way the handling of the indicator is
terminated.
Colour: Yellow
Position: TDMRU (TRU)
States of the indicator
ON: TX is not enabled
OFF TX is enabled
38.17 Local Mode Indicator
Purpose
To indicate the current RU Mode.
Preconditions and Initiation
Applicable for any operational condition. The function is initiated when
the SW is started.
Description
After a restart, the indicator is on until the Local Remote handling starts
(refer to the Restart and Recovery functionality). When the RU is reset
in any way the handling of the indicator is terminated.
Colour: Yellow
Position: CMRU (DXU) and TDMRU (TRU).
States of the indicator
ON: RU Mode is Local.
FLASHING (0.5 Hz): Change of RU mode is in progress:
− Waiting for layer 2 A-bis communication to be
established OR.
− Waiting for confirmation that the layer 2 A-bis
communication has been released.
OFF RU Mode is Remote.
EN/LZT 720 0008 R1A
2001-06-26
295 (421)
© Ericsson Radio Systems AB
— All Rights Reserved —