User Manual
Table Of Contents
- toc
- RBS Product Description
- 1 Introduction
- 2 Product Overview
- 3 Dimensions
- 4 Space Requirements
- 5 Environment
- 6 Hardware Units
- 7 Interfaces
- 7.1 External Connections
- 7.2 Test Interface
- 7.3 Operator Interface
- Figure 18 Power System
- 8.1 Power Supply
- 8.2 Battery Backup
- 8.3 Output Power to TM
- 8.4 Power Consumption
- 9 Transmission
- 10 External Alarms
- 11 Standards, Regulations and Dependability
- RBS Product Description
- tables
- Table 1 RBS Weights with Combined Climate Unit
- Table 2 RBS Weights with Heat Exchanger Climate Unit
- Table 3 RBS 2106 Colours
- Table 4 RBS 2106 Climatic Requirements
- Table 5 RBS 2106i and RBS 2106 V3 Climatic Requirements
- Table 6 Sound Pressure Level, Bystander Position without Sound H
- Table 7 Sound Pressure Level, Bystander Position with Sound Hood
- Table 8 Sound Pressure Levels for a Free Standing RBS with Combi
- Table 9 Sound Pressure Levels for an RBS against a Wall, with Co
- Table 10 Sound Pressure Level, Bystander Position without Sound
- Table 11 Sound Pressure Level, Bystander Position with Sound Hoo
- Table 12 Sound Pressure Levels for a Free Standing RBS€2106 with
- Table 13 Sound Pressure Levels for an RBS€2106 Against a Wall, w
- Table 14 Sound Pressure Level, Bystander Position without Sound
- Table 15 Sound Pressure Levels for a Free Standing RBS 2106i or
- Table 16 Sound Pressure Levels for an RBS 2106i or RBS€2106€V3 w
- Table 17 Compliance Boundary Dimensions for the General Public (
- Table 18 Characteristics of Typical Antenna
- Table 19 Maximum Power to Antenna for Various RBS€2106 Configura
- Table 20 Maximum Dimensions
- Table 21 Power Distribution for the TM Space
- Table 22 Connection Field Inlets in RBS 2106i and RBS 2106 V3
- Table 23 OVP Module Capacity
- Table 24 Overvoltage Arrestors
- Table 25 Antenna Connections
- Table 26 External Connections
- Table 27 Optical Indicators
- Table 28 Switches and Circuit Breakers
- Table 29 Power Parameters
- Table 30 Mains Fuses Recommendation
- Table 31 Output Power
- Table 32 Maximum Power Consumption during Battery Charging
Ericsson Internal
DESCRIPTION 32 ( 50 )
/ XSNSIXI 129/1551-LZA 701 0001 Uen
CBC/ XRX/M ( Kai Lian) 2011-05-05 F
Prepared (also subject responsible if other) No.
Approved Checked Date Rev Reference
Gas Collecting Kit
The acid leads can be supplied with a gas evaporating kit, which evacuates
gases from the cabinet.
Number of units: 0 – 1
HCU
The HCU contains three hybrid combiners. Each hybrid combines two RF
signals, delivered from the dTRU, into one.
Number of units: 0 – 1
OXU (RBS 2106 and RBS 2106i only)
The following Optional Expansion Unit (OXU) positions are available:
• Four spaces in the DXU/PSU subrack of the RBS 2106 and the RBS 2106i
(RUs that are typically located in the OXU slots include the DXX and the
TMA-CM)
• One 19-inch OXU position is available between the CXU and the CDU
subrack (used for HCU and ASU in co-sited cabinets)
Smoke Detector
The smoke detector is an optical device. Its purpose is to detect visual smoke.
When smoke enters the detector, a light beam is deflected towards a photocell
and an alarm is activated.
Number of units: 0 – 1
Sound Hood
The sound hood attenuates noise from the climate unit, heat exchanger, and
air condition.
Number of units: 0 – 1
TMA-CM
One or two Tower-Mounted Amplifier Control Modules (TMA-CM) can be used
to provide ddTMAs with 15 V DC power through the bias injectors. It also
identifies ddTMA faults and forwards this information to the alarm module in the
RBS. If TMA-CMs are used, then they are installed in the DXU/PSU subrack.
Number of units: 0 – 2
TM
The Transport Module (TM) is a space in the cabinet reserved for transmission
equipment. The RBS is type-approved with transmission equipment from
Ericsson. Equipment from other manufacturers requires a new type approval