User Manual
Table Of Contents
- toc
- RBS Product Description
- 1 Introduction
- 2 Product Overview
- 3 Dimensions
- 4 Space Requirements
- 5 Environment
- 6 Hardware Units
- 7 Interfaces
- 7.1 External Connections
- 7.2 Test Interface
- 7.3 Operator Interface
- Figure 18 Power System
- 8.1 Power Supply
- 8.2 Battery Backup
- 8.3 Output Power to TM
- 8.4 Power Consumption
- 9 Transmission
- 10 External Alarms
- 11 Standards, Regulations and Dependability
- RBS Product Description
- tables
- Table 1 RBS Weights with Combined Climate Unit
- Table 2 RBS Weights with Heat Exchanger Climate Unit
- Table 3 RBS 2106 Colours
- Table 4 RBS 2106 Climatic Requirements
- Table 5 RBS 2106i and RBS 2106 V3 Climatic Requirements
- Table 6 Sound Pressure Level, Bystander Position without Sound H
- Table 7 Sound Pressure Level, Bystander Position with Sound Hood
- Table 8 Sound Pressure Levels for a Free Standing RBS with Combi
- Table 9 Sound Pressure Levels for an RBS against a Wall, with Co
- Table 10 Sound Pressure Level, Bystander Position without Sound
- Table 11 Sound Pressure Level, Bystander Position with Sound Hoo
- Table 12 Sound Pressure Levels for a Free Standing RBS€2106 with
- Table 13 Sound Pressure Levels for an RBS€2106 Against a Wall, w
- Table 14 Sound Pressure Level, Bystander Position without Sound
- Table 15 Sound Pressure Levels for a Free Standing RBS 2106i or
- Table 16 Sound Pressure Levels for an RBS 2106i or RBS€2106€V3 w
- Table 17 Compliance Boundary Dimensions for the General Public (
- Table 18 Characteristics of Typical Antenna
- Table 19 Maximum Power to Antenna for Various RBS€2106 Configura
- Table 20 Maximum Dimensions
- Table 21 Power Distribution for the TM Space
- Table 22 Connection Field Inlets in RBS 2106i and RBS 2106 V3
- Table 23 OVP Module Capacity
- Table 24 Overvoltage Arrestors
- Table 25 Antenna Connections
- Table 26 External Connections
- Table 27 Optical Indicators
- Table 28 Switches and Circuit Breakers
- Table 29 Power Parameters
- Table 30 Mains Fuses Recommendation
- Table 31 Output Power
- Table 32 Maximum Power Consumption during Battery Charging
Ericsson Internal
DESCRIPTION 14 ( 50 )
/ XSNSIXI 129/1551-LZA 701 0001 Uen
CBC/ XRX/M ( Kai Lian) 2011-05-05 F
Prepared (also subject responsible if other) No.
Approved Checked Date Rev Reference
5.2.1 Heat Dissipation
The RBS 2106 (RBS 2106, RBS 2106i or RBS 2106 V3) generates an average
heat load of 3000 W. The exact figure is dependent upon configuration,
equipment, and site-specific conditions.
5.2.2 Acoustic Dispersion with Combined Climate Unit
The cabinet noise dispersion for an RBS 2106 (RBS 2106, RBS 2106i or
RBS 2106 V3) with Combined Climate Unit is shown in the tables below. The
figures and tables show the noise dispersion generated by a free-standing
cabinet and by a cabinet mounted against a wall.
Note: The acoustic noise dispersion values for a free-standing cabinet
and a cabinet installed against a wall were tested according to
the ISO 9614-2 standard. Deviations from these values can be
experienced due to the nature of materials in the environment where
the cabinet is installed. Objects near the cabinet can reflect or absorb
sound and thus affect acoustic dispersion.
The following two tables show the sound pressure levels, calculated at the
bystander position at a distance of 1 metre from the cabinet and 1.5 metre
above the floor. The calculations are valid in free field. If the RBS is placed in a
room the sound pressure level will be higher than indicated in the tables below.
Table 6 Sound Pressure Level, Bystander Position without Sound Hood
Sound Pressure Level at the Bystander Position at a
Distance of one Metre, L
pA
Db
Operating
Condition
Front Left Right Back
20
C
58 54
55
50
25
C
60 56
57
51
30
C
57
53 54 49
45
C
62 58 59 53
Table 7 Sound Pressure Level, Bystander Position with Sound Hood
Sound Pressure Level at the Bystander Position at a
Distance of one Metre, L
pA
Db
Operating
Condition
Front Left Right Back
20
C
51 50 51 49
25
C
50 49 50 48
30
C
48 48 48 47
45
C
54 52 53 51