Reference Manual
Table Of Contents
- RBS 2206 Reference Manual
- Contents
- Preface
- Product Safety Requirements RBS 2000
- Environmental Capabilities
- Scope
- Terminology
- References
- Transport -40 C - +70 C
- Storage -25 C - +55 C
- Handling -40 C - +70 C
- Operation Indoor +5 C - +40 C
- Operation Outdoor -33 C - +40 C
- Operation Outdoor -33 C - +45 C
- Operation Outdoor -33 C - +55 C
- Operation Mast Mounted Equipment -33 C - +45 C
- Operation Mast Mounted Equipment -33 C - +55 C
- Radio Configurations, RBS 2206
- Product Data
- Unit Description, DXU-21
- Unit Description, dTRU
- Unit Decription, CDU-G and CDU-F
- Unit Description, CXU-10
- Unit Description, FCU-01
- Unit Description, DC-Filter 01
- Unit Description, PSU 1200 W
- Unit Description, ACCU/DCCU
- Unit Description, IDM
- Broadcast
- Common Control Channel Handling
- Physical Channel Handling
- Speech and Data Services
- Packet Data Services
- Call Control
- References
- Channel Activation
- Adaptive Frame Alignment
- Asynchronous Handover Detection
- RF Channel Release
- Deactivate SACCH
- Link Establish Indication
- Link Release Indication
- Link Establishment Request
- Link Release Request
- Transparent Message Transmission
- Transparent Message Reception
- SACCH Info Modify
- LAPDm
- Channel Reactivation
- Power Information
- GPRS, Physical Link Layer
- Base Station Power Control
- Channel Measurements
- Discontinuous Transmission
- Frequency Hopping
- Encryption
- Mode Modify
- Mobile Station Power Control
- Short Message Service
- Diversity Supervision
- Synchronization
- Radio Reception
- Radio Transmission
- Frequency Allocation Support
- Restart and Recovery
- Function Change
- Functionality Administration
- Operation and Maintenance Support
- References
- Concepts
- Buttons
- Change RU to Local Mode
- Change RU to Remote Mode
- Change RU to Remote Mode Cancel
- Change SW Power Boost Slave RU to Local Mode
- Loop Control
- RF Loop Test Supervision
- Calendar Time Request
- RSSI Temperature Compensation
- Max Cooling
- Fault Indicator
- BS Fault Indicator
- Operational Indicator
- Tx Not Enabled Indicator
- Local Mode Indicator
- External Alarms Indicator
- DC Disconnected Indicator
- Battery Mode Indicator
- Bat Disconnected Indicator
- AC Fault Indicator
- Test Result Indicators (not used)
- Local Mode in Progress
- Installation Data Handling
- Self Test and Supervision
- Diagnostics and Fault Handling
- Operation and Maintenance Terminal
- External Alarms
- Handling of Auxiliary Equipment
- Climate Protection
- EMC Capabilities
- Transmission Interface Handling G.703 2048 kbit/s
- Transmission Interface Handling DS1 1544 kbit/s
- Terrestrial Link Handling
- Channel Distribution Function
- Transport network O&M functions-DXX Support
- BTS Parameter Limitations
- Glossary
Product Description 28 (33)
© Ericsson. Commercial in confidence Rev B 2001-05-16 SRN/X-00:146
6.2 CDU-types for GSM 1800
CDU-G 1800
dTRU
CDU-G
CDU-
G
dTRU
TXCout TX1
RXDA
DPX
DPX
RXDA
RXout1
RXin1
RXin2
RXin2
RXin1
TXCout TX2
RXout2
TX/RX
TX/RX
dTRU
CDU-G
dTRU
TX2
RXDA
DPX
DPX
RXDA
RXin2
RXin1
TXCout TX1
TXCout
TX/RX
TX/RX
dTRU
CDU-G
dTRU
TXCout TX1
RXDA
DPX
DPX
RXDA
RXout1
RXin1
RXin2
RXin2
RXin1
TXCout TX2
RXout2
TX/RX
TX/RX
CXU
RXin2
RXin1
RXout1
RXout2
Figure 10. CDU-G for GSM 1800 in a configuration with four TRX’s (two dTRU’s) in each sector.
Hybrids in the dTRU’s are used.
With CDU-G it is optional to use the hybrid combiner in the dTRU.
If the hybrid combiner is used 4 TRXs per cross-polarised antenna is supported. When the
hybrid combiner is by-passed the output power is maximised.
Synthesised or base band frequency hopping is allowed for all CDU-G configurations.
Sector 1
Sector 2
Sector 3