Reference Manual
Table Of Contents
- RBS 2206 Reference Manual
- Contents
- Preface
- Product Safety Requirements RBS 2000
- Environmental Capabilities
- Scope
- Terminology
- References
- Transport -40 C - +70 C
- Storage -25 C - +55 C
- Handling -40 C - +70 C
- Operation Indoor +5 C - +40 C
- Operation Outdoor -33 C - +40 C
- Operation Outdoor -33 C - +45 C
- Operation Outdoor -33 C - +55 C
- Operation Mast Mounted Equipment -33 C - +45 C
- Operation Mast Mounted Equipment -33 C - +55 C
- Radio Configurations, RBS 2206
- Product Data
- Unit Description, DXU-21
- Unit Description, dTRU
- Unit Decription, CDU-G and CDU-F
- Unit Description, CXU-10
- Unit Description, FCU-01
- Unit Description, DC-Filter 01
- Unit Description, PSU 1200 W
- Unit Description, ACCU/DCCU
- Unit Description, IDM
- Broadcast
- Common Control Channel Handling
- Physical Channel Handling
- Speech and Data Services
- Packet Data Services
- Call Control
- References
- Channel Activation
- Adaptive Frame Alignment
- Asynchronous Handover Detection
- RF Channel Release
- Deactivate SACCH
- Link Establish Indication
- Link Release Indication
- Link Establishment Request
- Link Release Request
- Transparent Message Transmission
- Transparent Message Reception
- SACCH Info Modify
- LAPDm
- Channel Reactivation
- Power Information
- GPRS, Physical Link Layer
- Base Station Power Control
- Channel Measurements
- Discontinuous Transmission
- Frequency Hopping
- Encryption
- Mode Modify
- Mobile Station Power Control
- Short Message Service
- Diversity Supervision
- Synchronization
- Radio Reception
- Radio Transmission
- Frequency Allocation Support
- Restart and Recovery
- Function Change
- Functionality Administration
- Operation and Maintenance Support
- References
- Concepts
- Buttons
- Change RU to Local Mode
- Change RU to Remote Mode
- Change RU to Remote Mode Cancel
- Change SW Power Boost Slave RU to Local Mode
- Loop Control
- RF Loop Test Supervision
- Calendar Time Request
- RSSI Temperature Compensation
- Max Cooling
- Fault Indicator
- BS Fault Indicator
- Operational Indicator
- Tx Not Enabled Indicator
- Local Mode Indicator
- External Alarms Indicator
- DC Disconnected Indicator
- Battery Mode Indicator
- Bat Disconnected Indicator
- AC Fault Indicator
- Test Result Indicators (not used)
- Local Mode in Progress
- Installation Data Handling
- Self Test and Supervision
- Diagnostics and Fault Handling
- Operation and Maintenance Terminal
- External Alarms
- Handling of Auxiliary Equipment
- Climate Protection
- EMC Capabilities
- Transmission Interface Handling G.703 2048 kbit/s
- Transmission Interface Handling DS1 1544 kbit/s
- Terrestrial Link Handling
- Channel Distribution Function
- Transport network O&M functions-DXX Support
- BTS Parameter Limitations
- Glossary
Product Description 16 (33)
© Ericsson. Commercial in confidence Rev B 2001-05-16 SRN/X-00:146
The Mini-DXC or DXX plug-in has the functionality of a Mini-DXC / DXX node, a
combination of Cross-connect, Control and G.703 interface units.
The TM-box (6HE) in the bottom of the cabinet can house customer specific transmission
equipment. If no internal batteries are used, additional customer specific transmission
equipment can be placed in the internal battery box. This gives a total space of 12HE.
In case customer specific equipment is set in this compartment the equipment must fulfil
the Electromagnetic Compatibility (EMC) requirements according to:
• ETS 300 342-2, the BTS product standard, in line with the European EMC Directive
89/336/EEC.
• FCC, part 15
The transmission box supports the equipment with 250 or 500 W. When 500 W is used the
PSU redundancy is reduced, the allowed heat generated in TM-box is max 300W and
transmission battery backup time will be slightly shorter.
3.10 Other Requirements
Product Safety
In accordance with the Low Voltage Directive (LVD 73/23/EEC plus 93/68/EEC) within
the European Union the RBS 2106 models comply with the following requirements
regarding product safety:
• EN 60 950/IEC 950
• EN 60 215/IEC 215
• EN 60 529/IEC 529
The RBS 2106 models are designed to fulfil the following safety standards in North
America:
• UL 1950, 2nd Edition, “Information Technology Equipment Including Electrical
Business Equipment”
• CSA C22.2 No. 950-95, “Safety of Information Technology Equipment Including
Electrical Business Equipment”
The RBS 2106 models are CE marked and UL listed in order to show this compliance.
Environmental Requirements
The requirements for climatic/mechanical environment are based on ETSI standard ETS
300 019 Classification of Environmental Conditions and IEC 721.
Storage Requirements
The RBS 2106 complies with ETS class 1.2 Weather Protected, Not Temperature
Controlled Storage Locations in ETS 300 019-1-1.