User`s guide

ManualsBrandsErgotron ManualsOffice FurnitureWorkFit-B

1 of 18

888-24-227-G-00 rev. B • 07/13

0.80”-1.75”*

(20-44 mm)

23.5”-30.5”*

(597-775 mm)

41"-72" *

(1041-1829 mm)

22.5-88 lbs (10.2-40 kg)*

User's Guide - English

Guía del usuario - Español

Manuel de l’utilisateur - Français

Gebruikersgids - Nederlands

Benutzerhandbuch - Deutsch

Guida per l’utente - Italiano

Användarhandbok - svenska

ユーザーガイド : 日本語

用户指南 : 汉语

www.ergotron.com

WorkFit-B, HD

Important! You will need to adjust this product after installation is

complete. Make sure all your equipment is properly installed on the

product before attempting adjustments. This product should move

smoothly and easily through the full range of motion and stay where

you set it. If movements are too easy or di cult or if product does

not stay in desired positions, follow the adjustment instructions to

create smooth and easy movements. Depending on your product

and the adjustment, it may take many turns to notice a di erence.

Any time equipment is added or removed from this product,

resulting in a change in the weight of the mounted load, you

should repeat these adjustment steps to ensure safe and optimum

operation.

*Total weight of worksurface and mounted equipment must

be < 88 lbs (40 kg).

Worksurface must meet ALL dimensional and weight range

speci cation requirements.

WARNING! The addition of accessories can negatively impact the

tip performance.

Wood Worksurface Weight Estimator

Worksurface

Thickness

Estimated Weight

per square foot

0.80” (20 mm) 2.9 lbs (1.32 kg)

1.25” (32 mm) 4.5 lbs (2.04 kg)

1.75” (44 mm) 6.3 lbs (2.86 kg)

Summary of content (18 pages)

PAGE 1
WorkFit-B, HD www.ergotron.com User's Guide - English Guía del usuario - Español Manuel de l’utilisateur - Français Gebruikersgids - Nederlands Benutzerhandbuch - Deutsch Guida per l’utente - Italiano Användarhandbok - svenska ユーザーガイド : 日本語用户指南 : 汉语 22.5-88 lbs (10.2-40 kg)* 0.80”-1.75”* (20-44 mm) 41"-72" * (1041-1829 mm) 23.5”-30.5”* (597-775 mm) Important! You will need to adjust this product after installation is complete.
PAGE 2
Hazard Symbols Review Symbol These symbols alert users of a safety condition that demands attention. All users should be able to recognize and understand the significance of the following Safety Hazards if encountered on the product or within the documentation.
PAGE 3
Safety WARNING! Stop screws are pre-installed in this product to secure it in the compressed position during shipping and installation. DO NOT REMOVE THESE SCREWS UNTIL INSTRUCTED TO DO SO IN THESE INSTRUCTIONS. Make sure these screws are in place before starting installation. Failure to follow these instructions may cause lift engine to expand rapidly and may result in equipment damage and or personal injury.
PAGE 4
Safety Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or difficult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
PAGE 5
Components A B 1x C 1x 1x 1 2x 16x 2 M5 x 6mm 17x #12-14 x 5/8” 3x 3x 3 M2.9 x 8mm 2x 4.25” (108 mm) 3.75” (95 mm) 3.25” (83 mm) 1x 2.75” (70 mm) 2.25” (57 mm) 1.75” (44 mm) 1.25” (32 mm) 0.75” (19 mm) ST3.9 x 16mm 4.25” (108 mm) WORKSURFACE TEMPLATE FOR WORKFIT-B, HD Lay this template on the bottom of your worksurface See table for value of X based on the depth of to drill the holes to attach the WorkFit-D, Base. your worksurface. 3.75” (95 mm) 3.
PAGE 6
Set-up Steps 1 Place the worksurface on a clean floor with the top side facing down. Center Template Side-to-Side on worksurface. , Bit #46 (2mem) UseØDrill s 0.081”thes 3 hole ) deep. to drill 0.24” (6 mm , Bit #21mm ) Use Drill ” (4.8e 9 holes Ø 0.19thes ) deep. to drill 3/8” (9.5 mm , Bit #21mm ) Use Drill ” (4.8these 8 holes p. Ø 0.19drill ) dee to 3/8” (9.5 mm Brake Rele kets of Base Brac e Bracket ts. ! unstabl Basepro duc al HAZARD Across injury.
PAGE 7
Set-up Steps Using the specified drill bit, drill the 17 holes for base. #21, Ø 0.19” (4.8mm) Drill holes 0.375" (9.5 mm) deep. TIP: To ensure proper depth, place a piece of tape on the drill bit 0.375” (9.5 mm) from the tip. , ll Bit #46 (2mm) holes UseØDri 0.081” ll these 3 ) deep. to dri 0.24” (6 mm #21, ) ll Bit(4.8 mm Use Dri Ø 0.1ll9”the se 9 hol) es deep. to dri3/8 ” (9.5 mm #21, ) ll Bit(4.8 mm 8 holes Use Dri se ) deep. Ø 0.19” to drill”the 3/8 (9.5 mm Brackets nt of Base ts.
PAGE 8
Front Edge of Worksurface Set-up Steps 2 Place the worksurface on a clean floor with the top side facing down. Carefully position the leg with the hand brake on the right end of the worksurface. Place the other leg on the left end. Rear Edge of Worksurface NOTE: The brake cable is attached to both legs. Take care when removing the legs from the packaging to avoid damaging or pulling the brake cable from the legs. 3 Set the right leg (with hand brake) upright on the worksurface.
PAGE 9
WARNING Set-up Steps Keep Brake Cables Away from Sync Rod and Crossbars During Installation! Failure to keep the brake cables away from sync rod and crossbars may restrict lift motion and may cause equipment damage or personal injury! Refer to instruction manual for more information. 5 Set the left leg (without hand brake) upright on the worksurface. Attach the left end of the sync rod to the left leg. Make sure the brake cables don’t loop around the sync rod. See Warning, right.
PAGE 10
Set-up Steps 9 If your brake release handle is not aligned with the front edge of your worksurface and you would like it to be, follow these instructions to relocate the brake release handle. a b c Relocate brake release handle along front edge of worksurface and next to the inside of the leg only. DO NOT attach brake release handle in front of or to the outside of the leg. Make sure cable has enough slack to allow worksurface to fully extend up and down. #46, Ø 0.081” (2mm) d 4x ST3.
PAGE 11
Set-up Steps 10 11 Capture the brake cable in the cable clip as illustrated, then use a Phillips screwdriver to attach the cable clips to bottom of work surface with the provided M2.9 x 8 mm screws. 3x Using the 2 provided cable ties, attach brake cable to the legs leaving as much slack in cable as possible between the cable tie and the leg to allow desk top to raise up unrestricted. 3x M2.
PAGE 12
Set-up Steps 12 Set the desk upright onto its legs. CAUTION! LIFT HAZARD! Two persons are required for this step. Failure to follow this warning may result in equipment damage and or personal injury. 13 Adjust the riser on each leg and check with a level to make sure the work surface is even. Spin Left to Raise. Spin Right to Lower. 888-24-227-G-00 rev.
PAGE 13
Set-up Steps 14 Remove the 4 brake stop screws before installing equipment. Remove the 2 stop screws from the legs then the 2 stop screws from the brake to allow the worksurface to raise and lower. 1 IMPORTANT! Save these stop screws and instructions. Install stop screws when shipping or storing this product. Failure to follow these instructions may cause lift engine to expand rapidly and may result in equipment damage and or personal injury. 2 2.
PAGE 14
Set-up Steps 15 Install all equipment. CAUTION! Make sure you leave 20” (508mm) of slack in all equipment cables to allow the worksurface to raise up it’s full 20” (508mm). Failure to allow enough slack in equipment cables may cause cables to get pulled, equipment to fall off desk and may result in product damage and or personal injury. 16 Adjustment Step Important! You will need to adjust this product after installation is complete.
PAGE 15
17 Adjustment Step Release the hand brake (on the right leg) and move the worksurface up to highest level. Push in the cover located behind each leg to access the adjustment point. NOTE: The covers on the legs will not open unless the worksurface has been lifted to it’s full height. The worksurface will not lower unless the covers have been completely closed. Maintain equal amount of tension on both legs by alternating the adjustment from one leg to the other using a 14mm socket drill.
PAGE 16
APPENDIX A - Minimize Lift Tension WARNING. Before removing mounted equipment (monitor, arm, stand CPU, etc.), from desk, or to prepare for shipping or storing the desk it is extremely important to minimize the lift tension. Failure to install these instructions may cause lift engine to expand rapidly and may result in equipment damage and or personal injury. 1. Release the hand brake (on the right leg) and move the worksurface up to highest level. 2.
PAGE 17
APPENDIX B - Inserting Stop Screws WARNING. Before shipping or storing the desk, or in cases where the desk is placed on it’s back or side*, it is extremely important that the 4 stop screws be re-inserted. Failure to follow these instructions may cause lift engine to expand rapidly and may result in equipment damage and or personal injury. 1. Follow instructions in Appendix A to minimize lift tension. 2. Push the desk down to its lowest position. 3. Insert 2 stop screws at the bottom of each leg. 4.
PAGE 18
Set Your Workstation to Work For YOU! Configure su estación de trabajo para que trabaje para USTED. Ajustez votre station de travail en fonction de VOS besoins ! Richten Sie Ihren Arbeitsplatz so ein, dass er für SIE arbeitet! Stel uw werkstation zo in dat het voor U werkt! Approntare la stazione di lavoro nella posizione ergonomica ottimale.