User Manual

ManualsBrandsErgotron ManualsDesk Accessories & Workspace OrganizersLX Desk Mount LCD Arm, Tall Pole

1 of 9

888-45-040-W-03 rev.U • 09/14

LX Desk Mount LCD Arm

AB CDE

5 - 25 lbs*

(2.3 - 11.3 kg)

M4 x 10mm

4mm

M3 x 6mm

5°

70°

360°

180°

13"

(330 mm)

2.5mm

User's Guide - English

Guía del usuario - Español

Manuel de l’utilisateur - Français

Gebruikersgids - Deutsch

Benutzerhandbuch - Nederlands

Guida per l’utente - Italiano

Användarhandbok - svenska

ユーザーガイド : 日本語

用户指南 : 汉语

Includes

Constant Force™

Technology

< 4.5” (114 mm)

8.5” (216 mm)

ENGLISH

ASSEMBLY INSTRUCTIONS

For the latest User Installation Guide please visit: www.ergotron.com

* The lower most range of motion for vertical lift is

decreased up to 4.5” (114 mm) when arm is adjusted to

hold over 20lbs (9 kgs).

Summary of content (9 pages)

PAGE 1
ASSEMBLY INSTRUCTIONS LX Desk Mount LCD Arm * The lower most range of motion for vertical lift is decreased up to 4.5” (114 mm) when arm is adjusted to hold over 20lbs (9 kgs). 8.5” (216 mm) 5 - 25 lbs* (2.3 - 11.3 kg) < 4.5” (114 mm) 360° 70° 360° 13" 180° A 5° B 1x 1 ENGLISH (330 mm) C D 1x 4x E 1x 4mm M4 x 10mm 1x 1x 4x 2 1x M4 x 10mm 1x 3 1x 1x 1x 2.5mm 2x M3 x 6mm For the latest User Installation Guide please visit: www.ergotron.
PAGE 2
Hazard Symbols Review These symbols alert users of a safety condition that demands attention. All users should be able to recognize and understand the significance of the following Safety Hazards if encountered on the product or within the documentation.
PAGE 3
C/L 19” (483mm) 1 C/L < 0.4" (10 mm) 0.47" - 1.38" (12 - 35 mm) 1.46" - 2.4" (37 - 60 mm) 4mm < 2.25" (57 mm) b c 4mm ENGLISH a 0.31" - 2"* (8 - 51 mm) d CAUTION: For secure arm attachment and to avoid equipment damage, plate must make contact with underside of desk on both sides of the hole. CAUTION: Bolt must be centered in hole. 888-45-040-W-03 rev.
PAGE 4
2 4x M4 x 10mm 4x M4 x 10mm ENGLISH 360° M3 x 6mm 360° 0° WARNING WARNING! Stored Energy Hazard: The arm mechanism is under tension and will move up rapidly, on its own, as soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the arm has been moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or equipment damage! 888-45-040-W-03 rev.
PAGE 5
3 2.5mm ENGLISH 888-45-040-W-03 rev.
PAGE 6
4 NOTE: Leave enough slack in cable to allow full range of motion. ENGLISH Caution: To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow these instructions may result in equipment damage or personal injury. 5 888-45-040-W-03 rev.
PAGE 7
6 Lift – Up and down a 4mm 4mm CAUTION: DO NOT overtighten fasteners. Overtightening may cause damage to your equipment. Increase Lift Strength If the mounted weight is too heavy or this product does not stay up when raised, then you'll need to increase Lift Strength: Decrease Lift Strength If the mounted weight is too light or this product does not stay down when lowered, then you'll need to decrease Lift Strength: ENGLISH b Tilt – Forward and Backward 4mm 4mm CAUTION: DO NOT remove screw.
PAGE 8
c Arm Swing – Side-to-side 2.5mm Increase Friction If this product moves too easily, then you'll need to increase friction: Decrease Friction ENGLISH If this product is too difficult to move, then you'll need to decrease friction: d Rotate – Portrait/Landscape 360° 0° M3 x 6mm 888-45-040-W-03 rev.
PAGE 9
Set Your Workstation to Work For YOU! Learn more about ergonomic computer use at: www.computingcomfort.org Height Position top of screen slightly below eye level. Position keyboard at about elbow height with wrists flat. Distance Position screen an arm's length from face—at least 20” (508mm). Position keyboard close enough to create a 90˚ angle in elbow. Angle Tilt screen to eliminate glare. Tilt the keyboard back 10° so that your wrists remain flat.