WorkFit-A, Single LCD Mount, LD ASSEMBLY INSTRUCTIONS ENGLISH For local customer care phone numbers visit: http://contact.ergotron.com For the latest User Installation Guide please visit: www.ergotron.com User's Guide - English Guía del usuario - Español Manuel de l’utilisateur - Français Gebruikersgids - Deutsch Benutzerhandbuch - Nederlands Guida per l’utente - Italiano Användarhandbok - svenska ユーザーガイド : 日本語 用户指南 : 汉语 Includes Constant Force™ Technology 888-45-298-W-02 rev.
Warning: Because mounting surface materials can vary widely, it is imperative that you make sure mounting surface is strong enough to handle mounted product and equipment. Adjust the height of your desk (or chair and footrest) to allow the keyboard to lower to your sitting elbow height for ergonomic computing. Caution: To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual.
Set Your Workstation to Work For YOU! Learn more about ergonomic computer use at: www.computingcomfort.org To Reduce Fatigue Breathe - Breathe deeply through your nose. Blink - Blink often to avoid dry eyes. Break • 2 to 3 minutes every 20 minutes • 15 to 20 minutes every 2 hours. Height Position top of screen slightly below eye level. Position keyboard at about elbow height with wrists flat. Distance Position screen an arm's length from face—at least 20” (508mm).
1 Arm Extension and Desk Size: The keyboard tray is designed to extend over the edge of your desk. You can expand the extension of the arm if you need to based on your desk size. To determine if you need to expand your arm extension, refer to the 4 desk dimensions below: CLAMP 9.5" (250 mm) GROMMET HOLE 6 CAUTION: Base must be completely on desk surface. Failure to follow these instructions may result in equipment damage or personal injury. 9.
How to expand the arm extension. a b c 180˚ base using the provided 4mm hex wrench. 180˚ d2 Flip the base around (turn d3 Re-insert the 4 screws and tighten 180 degrees. with the 4mm hex wrench. 4 mm 888-45-298-W-02 rev.
2 CLAMP a DESK THICKNESS ENGLISH GROMMET HOLE 4 mm 4 mm 0.78"-1.78" (20-45mm) 1.70"-2.56" (43-65mm) b 4 mm c 1x 1x 8mm 1/4” 1/4" d 1x 1x CAUTION: Bolt must be centered in hole. 888-45-298-W-02 rev.
3a 2x M6 x 45mm 4 mm ENGLISH b c 2x M5 x 35mm WARNING! Screws must be tightened to keep product secure. Failure to follow these instructions will create an unstable situation and may result in equipment damage or personal injury. 888-45-298-W-02 rev.
4 a 1x b c 2x ENGLISH M4x16mm 888-45-298-W-02 rev.
5a b M5 x 8mm ENGLISH 6 1x 4 mm 1x M3 x 6mm 0° 4x M4 x 10mm 4x M4 x 10mm 888-45-298-W-02 rev.
7 8 4x 1x 1x 4x ENGLISH M4 x 10mm 9 NOTE: Leave enough slack in cable to allow full range of motion. Caution: To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow these instructions may result in equipment damage or personal injury. 8x 1x 888-45-298-W-02 rev.
10 Adjustment Step Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or difficult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
b 8mm 1/4” 1/4" Increase Lift Strength If the mounted weight is too heavy or this product does not stay up when raised, then you'll need to increase Lift Strength: Decrease Lift Strength ENGLISH If the mounted weight is too light or this product does not stay down when lowered, then you'll need to decrease Lift Strength: c Increase Friction If this product moves too easily from side-to-side, then you'll need to increase friction: Decrease Friction If this product is too difficult to move from side-
d 8mm 1/4” 1/4" Increase Friction If this product moves too easily from side-to-side, then you'll need to increase friction: Decrease Friction If this product is too difficult to move from side-to-side, then you'll need to decrease friction: 1/4” 1/4" Increase Friction If this product moves too easily from side-to-side, then you'll need to increase friction: Decrease Friction If this product is too difficult to move from side-to-side, then you'll need to decrease friction: f 4 mm Increase Friction
f Angle Setting Adjustment 1 Loosen these two screws. 2 Loosen or tighten this bolt to adjust tilt to desired angle. 4 mm ENGLISH Tighten to tilt up. Loosen to tilt down. 3 After desired tilt is achieved, retighten these two screws to secure. WARNING! Screws must be tightened to keep product secure. Failure to follow these instructions will create an unstable situation and may result in equipment damage or personal injury. © 2015 Ergotron, Inc. 888-45-298-W-02 rev.
