ERB386GRD 710W 115mm ANGLE GRINDER
Original Instructions (Version 1.
Congratulations on your purchase of a quality power tool from Erbauer (UK) Ltd. This product should give you reliable service but for your peace of mind this power tool does carry a 2 year guarantee, the terms of which are detailed below. If this product develops a fault within the guarantee period contact your retailer. Please retain this handbook in case you need to refer to safety, care or guarantee information in the future. GUARANTEE This product carries a 2 year guarantee.
GENERAL POWER TOOL SAFETY WARNINGS Warning: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your electric (corded) power tool or batteryoperated (cordless) power tool. 1. Work area safety a. Keep work area clean and well lit. Cluttered or dark areas invite accidents. b.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. 4. Power tool use and care a. Do not force the power tool. Use the correct power tool for your application.
3. Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation. 4. The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart. 5. The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool.
Further safety instructions for all operations Kickback and Related Warnings Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory’s rotation at the point of the binding.
Additional safety instructions for cutting-off operations Additional Safety Warnings Specific for Abrasive Cutting-Off Operations: 1. Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage. 2. Do not position your body in line with and behind the rotating wheel.
VIBRATION The European Physical Agents (Vibration) Directive has been brought in to help reduce hand arm vibration syndrome injuries to power tool users. The directive requires power tool manufacturers and suppliers to provide indicative vibration test results to enable users to make informed decisions as to the period of time a power tool can be used safely on a daily basis and the choice of tool. Further Advice can be found at www.hse.gov.
Avoid using tools in temperatures of 10ºC or less. Plan your work schedule to spread any high vibration tool use across a number of days. Health Surveillance All employees should be part of an employer’s health surveillance scheme to help identity any vibration related diseases at an early stage, prevent disease progression and help employees stay in work. Double insulation The tool is double insulated. This means that all the external metal parts are electrically insulated from the mains power supply.
SYMBOLS To reduce the risk of injury, user must read instruction manual Warning Double insulation Wear ear protection Wear eye protection Wear dust mask Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
4 2 1 3 9 5 8 7 6 10 11 12 13
1. ON-OFF SWITCH 2. main hand area 3. AUXILIARY HANDLE 4. SPINDLE LOCK BUTTON 5. OUTER FLANGE 6. INNER FLANGE 7. SPINDLE 8. GRINDING DISC 9. SPANNER 10. PROTECTION GUARD FOR GRINDING 11. CLAMPING SCREW 12. CODED PROJECTION 13.
TECHNICAL DATA Rated voltage 230-240V~50Hz Rated input power 710W Rated speed 11000/min Protection class /II Spindle thread M14 Disc size 115mm Disc bore 22.2mm Machine weight 2.3 Kg NOISE INFORMATION A weighted sound pressure: A weighted sound power: Wear ear protection when sound pressure is over LpA: 88 dB (A) LwA: 99 dB (A) KPA=3.0 dB (A) KWA=3.
OPERATING INSTRUCTIONS Note: Before using the tool, read the instruction book carefully. Intended Use The machine is intended for cutting, roughing and brushing metal and stone materials without using water. For cutting metal, a special protection guard for cutting ( accessory) must be used. Assembly and Adjustment Mounting the Protective Devices 1. AUXILIARY HANDLE For all work with the machine, the auxiliary handle (3) must be mounted.
3. Adjustable outer flange clamping The outer flange (5) should be adjusted to suit different disc thickness. For thinner cutting discs the raised part of the outer flange is fitted facing away from the disc (See Fig.3-1). For thicker grinding discs the raised part of the outer flange is fitted facing towards the disc to provide improved support for the disc hole (See Fig.3-2). Always ensure your disc is securely clamped.
1. Hand grip areas Always hold your angle grinder firmly with both hands when operating (See Fig.5). 2. Rough Grinding The best roughing results are achieved when setting the machine at an angle of 30° to 40°. Move the machine back and forth with moderate pressure. In this manner, the workpiece will not become too hot, does not discolour and no grooves are formed. Warning! Never use a cutting disc for roughing. Fig. 5 3. Cutting Warning: For cutting metal, always work with the wheel guard for cutting.
WORKING HINTS FOR YOUR ANGLE GRINDER If your power tool becomes too hot, run no load for 2-3 minutes to cool the motor. Never start your angle grinder with the disc/ accessory in contact with the workpiece. Always start at no load to achieve maximum speed then start working. Do not force the disc to work faster, reducing the Disc’s moving speed means longer working time. When grinding, always work with a 30° to 40° angle between disc and workpiece.
Maintenance Remove the plug from the socket before carrying out any adjustment, servicing or maintenance. Your power tool requires no additional lubrication or maintenance. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots.
PLUG REPLACEMENT (UK & IRELAND ONLY) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: BLUE =NEUTRAL Brown = Live As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows. The wire which is colored blue must be connected to the terminal which is marked with N.
Declaration of Conformity We, Importer Erbauer (UK) Ltd BA22 8RT Declare that the product Description: 710W 115mm Angle grinder Model: ERB386GRD Complies with the following Directives, EC Machinery Directive 2006/42/EC EC Low Voltage Directive 2006/95/EC EC Electromagnetic Compatibility Directive 2004/108/EC Restrictions of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment 2002/95/EC Waste Electrical and Electronic Equipment (WEEE) 2002/96/EC and 2003/108/EC Standards conform to
