Technical data

14
the burner there are only a dose of pellets which burns out during the
pause of the transporter and the safe burning of the fuel is secured.
· A sensor for temperature higher than 90-95
0
C – it is placed on the feeding
tube of the burner. If during work the temperature sensor detects a
temperature higher than 90–95
0
Ñ, the auger transporter stoppes and the
burner turns off. At this time a lamp ALARM starts to light. Even if the
temperature falls below 90–95
0
Ñ, the burner won’t start working again. It
is necessary the intervention of the operative staff. After fixing the error
in the normal work, the burner starts by its turning off and on. This can
be done by the POWER switch placed on the burner’s cover (it stoppes
the feeding of the logistical module in the burner and clears the alarm),
or by stopping the common feeding of the boiler through its main switch.
Ñ- ÌÎÍÒÀÆ ÍÀ ÃÎÐÅËÊÀÒÀ È ÏÓÑÊÀÍÅ Â ÅÊÑÏËÎÀÒÀÖÈß
Ñ. INSTALLATION AND GETTING IN OPERATION OF THE BURNER
Ñ-1. ÑÂÚÐÇÂÀÍÅ ÊÚÌ ÊÎÒÅËÀ
-Ñúîðúæåíèåòî òðÿáâà äà áúäå ðàçïîëîæåíî òàêà, ÷å äà èìà äîñòàòú÷íî
ñâîáîäíî ìÿñòî çà ÷èñòåíå, îòñòðàíÿâàíå íà ñàæäèòå îò ãîðåëêàòà, êîòåëà è
òðúáèòå çà èçãîðåëè ãàçîâå.
- Ãîðåëêàòà ñå ïîñòàâÿ â îòâîðà íà êîòåëà ñúñ ñúîòâåòíîòî óïëúòíåíèå.
Çàêðåïâà ñå ñ ãàéêè, êàòà ïîä åäíàòà ñå ïîñòàâÿ ÑÏÅÖÈÀËÅÍ “Ô-ÎÁÐÀÇÅÍ
ÄÅÒÀÉË ÎÒ ËÀÌÀÐÈÍÀ, êîÿòî ñëóæè çà íàòèñêàíå íà êðàéíèÿ èçêëþ÷âàòåë,
ÄÀÂÀÙ ÈÍÔÎÐÌÀÖÈß, ×Å ÃÎÐÅËÊÀÒÀ Å ÌÎÍÒÈÐÀÍÀ. Àáñîëþòíî ñå
çàáðàíÿâà åëèìèíèðàíåòî íà òàçè çàùèòà, òúé êàòî å ñâúðçàíà ïðÿêî ñ
ïîæàðíàòà áåçîïàñíîñò.
- Êîíòàêòà ìåæäó ãîðåëêàòà è êîòåëà òðÿáâà äà áúäå äîáðå óïëúòíåí, ñ öåë
äà íå ñå ïîëó÷è èçòè÷àíå íà èçãîðåëè ãàçîâå â êîòåëíîòî.
- Ïðè ìîíòèðàíåòî òðÿáâà äà ñå îáúðíå âíèìàíèå íà òîâà, ñúîðúæåíèåòî äà
å â îïòèìàëíî õîðèçîíòàëíî ïîëîæåíèå. Ìàðêó÷úò òðÿáâà äà áúäå èçïúíàò
è âðúçêèòå òðÿáâà äà áúäàò çàòåãíàòè.
Ñ-1. CONNECTING TO THE BOILER
- The device should be placed a in way, so there will be enough space for cleaning,
removing the soot from the burner, the boiler and the draught pipes.
- The burner must be installed in the boiler outlet with the relevant isolation. It
must be joined up with nuts. Under one of the nuts there must be put a SPECIAL
T-FIGURE TIN DETAIL which is for pushing the limit switch, INFORMING THAT
THE BURNER IS INSTALLED. It is absolutely forbidden the eliminating of this
protection since it is directly connected to the fire safety.