Specifications

p 10
Eraser Company Inc. • Syracuse, NY USA • Ph: 315-454-3237 • [e-mail] • www.eraser.com • Fax [phone]
With this last batch, the example kit is completely
dened. When the kit is fully dened, the operator
presses the <RUN> key to run the kit, or the <ESC/
PAUSE> key to go back to the KIT SELECT screen.
A <RUN> key press displays the KIT QUANTITY
screen:
QUANTITY: 0 KIT#1
ENTER 0 FOR MANUAL
OR # FOR AUTOMODE
AUTOMODE KIT OPERATION (PROCESSING A
KIT AT A SPECIFIC QUANTITY):
Kit quantities must be entered each time a kit is
called up and processed, they are not stored in
the kit’s program or from the last run. The cursor
is now at the ‘QUANTITY:’ parameter. For our
example, we’ll process a quantity of ten (10) kits, as
programmed (Kit #1). When a kit quantity is entered,
the machine will output kits continuously until the
entered quantity of kits has been processed. The
operator presses the <1> key, the <0> key, then
the <ENTER> or the <RUN> key. The KIT START
screen displays:
JOG - JOG
CUT - CUT
SAVE - ENTER
START – RUN
MANUAL MODE & SAVE OPERATIONS:
A <JOG> or <+> key press at this screen will
advance material through the feed belts (Manual
Mode) for as long as the key is held. A <-> key press
will reverse material (Manual Mode) for as long as
the key is held.
A <CUT> key press will cycle the blade once
(Manual Mode).
An <ENTER> key press saves the kit and brings the
operator back to the BATCH SELECT screen.
Continuing our example of 10 kits of Kit #1, the
operator presses the <RUN> key at the KIT
START screen (above). As soon as the <RUN>
key is pressed, kit processing begins, and the KIT
PROCESSING STATUS screen displays:
# OF KITS 10 KIT #1
KITS LEFT X
CURRENT BATCH Y
PIECES LEFT Z
During Automode Kit Processing (running a quantity
of kits) the KIT PROCESSING STATUS screen
(above) displays the quantity of kits programmed
and the kit number on the rst (top) line. This line
is static – it will not change during kit processing.
The second line (‘KITS LEFT’) counts down the
number of kits left to be processed. The third line
(‘CURRENT BATCH’) displays the current batch
being processed. The fourth (bottom) line (‘PIECES
LEFT’) displays the number of pieces left in the
current batch (not the kit) being processed.
During kit processing, the operator can press the
<ESC/PAUSE> key to stop kit processing and
display the KIT ESCAPE screen:
JOG - JOG
CUT - CUT
ABORT - ESC
CONTINUE - RUN
At this point the operator can jog or cut material
manually (see Manual Mode & Save Operations
section above), or continue the kit run by pressing
the <RUN> key. The kit will resume processing
from the point at which it was stopped. Pressing the
<ESC/PAUSE> key from the KIT ESCAPE screen
(ABORT command) brings the operator to the KIT
RUN COMPLETE screen (below). When all kits
have been processed, the KIT RUN COMPLETE
screen displays:
RUN COMPLETE KIT #1
KITS LEFT 0
PUSH ANY KEY
Pressing any key will bring the operator back to the
BATCH SELECT screen. To return to kit processing/
programming from the BATCH SELECT screen,
press the < . > key.
MANUAL (SINGLE) KIT OPERATION:
(Using the default kit quantity of ‘0’)
In Manual Kit Mode, one (1) kit is processed per
<RUN> key press (even though ‘0’ is entered as a
quantity – in this instance, ‘0’ designates Manual
[Single] Kit Mode). After pressing the <ENTER>
MODEL WC601A AUTOMATIC WIRE & TUBING CUTTER