Manual Desktop KVM Switch english www.equip-info.
Manual_Page 2 Content 1. 2. 3. 4. 5. 6. 6.1 7. 7.1 7.2 7.2.0 7.2.1 7.2.2 7.2.
Manual_Page 3 1. Introduction Thank you for your purchase of Combo KVM Switch! You now have a high quality, durable system that will enable you to control 2/4 Host computers and/or servers by using PS/2 and/or USB Connectors from one console (PS/2 Mouse & PS/2 Keyboard, and Monitor). 2. Features 1. Complex connections with PCs via either way of PS/2 and/or USB arbitrarily. 2. Controls 2 / 4 computers from a single console PS/2 (Keyboard/Mouse) over PS/2 and/or USB connections. 3.
Manual_Page 4 4. Specifications 5. System Requirements Console A VGA, SVGA, Multisync monitor capable of the highest resolution. PS/2 Keyboard/Mouse Computer or Server The following equipment must be equipped with each computer or server. - A VGA, SVGA or Multisync card. - Type A USB port or PS/2 6 pin mini-DIN for Keyboard and Mouse. www.equip-info.
Manual_Page 5 Cables The Combo Free KVM Switch must be used specific custom 4-in-1 cables. To purchase the specific cable sets, please contact your dealer. The cables are available in 1.8m, 3m and 5m length (item numbers 331992, 331993, 331995). 6. Installation LED Indicators: RED LED “Selected”: indicates that the KVM Switch is selected to the corresponding PC. GREEN LED “On-Line”: indicates that the KVM Switch is ready to the corresponding PC. Reset Switch: Press this switch when a system reset.
Manual_Page 6 System connecting: Use KVM custom cable sets to connect any available PC ports to the video and either USB or PS/2 ports alternatively, or even USB & PS/2 both all connected to the computers you are connecting up. ( Fig 1 ) combo custom 4-in-1 cable Note: The custome cable set, as Fig. 1, is not supplied with this package; it has to be purchased separately. The cables are available in 1.8m, 3m and 5m length (item numbers 331992, 331993, 331995).
Manual_Page 7 This KVM Switch with custom specific cable set provide three connecting methods. 1. Plug USB, PS/2 ( keyboard/mouse) ports and VGA into PCs at same time, recommended in priority. 2. Plug only PS/2 (keyboard / mouse) ports and VGA into PCs. 3. Plug only USB and VGA into PCs. 7. Operations The 2 / 4-Port Combo KVM Switch has the ability to switch the keyboard, video, mouse simultaneously.
Manual_Page 8 7.2.0 Hotkey Selection Hot Key: [Ctrl] -> [Ctrl] -> [Caps Lock] -> [Enter] : The hotkey changed to [Caps Lock] [Ctrl] -> [Ctrl] -> [Num Lock] -> [Enter] : The hotkey changed to [Num Lock] [Ctrl] -> [Ctrl] -> [Scroll Lock] -> [Enter] : The hotkey reversed to [Scroll Lock] Note : The default hotkey setting is , after you changing the hotkey setting, the new setting will effect on the KVM until power off or reset. 7.2.
Manual_Page 9 7.2.2 Auto-Scan Function Hot Key: [Scroll] -> [Scroll] -> [S] -> [Enter] to BEGIN. [Scroll] -> [Scroll] -> [S] -> [Enter] to STOP. You can activate the Auto-Scan function by using the following two-step Hot Key sequence. To send commands to the Combo KVM Switch, press the [Scroll] key twice (Step 1), then press [S] and then press [Enter] (Step 2). When you press the Auto-Scan hot key sequence, the Combo KVM Switch alternates between the two or four PCs and displays them on the monitor.
Manual_Page 10 Hot Key definition table Sun Microsystems Function Key Emulation: There are 16 special functions on the Sun Microsystems keyboard, the Combo KVM Switch can emulate these function keys via the PS/2 keyboard. Here is the mapping table for these functions operation. To active these emulation on the PS/2 keyboard, you have to press the LEFT Window KEY first (this key usually is located between the left [Ctrl] and left [Alt]), then choice the second relative key. www.equip-info.
