Electric Hybrid Cooktop 23” Built-In 2 Induction + 2 Ceramic Model: EHC 23422 Hybrid Induction-Ceramic Keep Warm POWER Pause II
Insufficient spacing around appliance Website: EquatorAppliances.com QR Code 1. Open Smart Phone 2. Open Camera 3. Scan QR Code 4.
Congratulations on your new Hybrid Induction-Ceramic Cooktop! In addition to its contemporary design, this is a highly sophisticated engineered product that will give you many years of satisfaction.
Installation Follow cutout dimensions of the countertop as indicated on the diagram. Before cutting out the countertop, check that the dimensions in the diagram correspond to the dimensions of the product. Ensure the work surface is heat-resistant and is at least 1.2 inches thick. Ensure the safety distance between the sides of the cooktop and the inner surfaces of the countertop is at least 0.12 inches. Keep a space of at least 0.2 inches around the cut-out.
Ensure that the following conditions are met for adequate ventilation of the cooktop and that the supply and exhaust air is not blocked: The safety distance between the cooktop and the cabinet or the vent hood should be at least 30 inches. If the cooktop is installed above an oven, the oven must have its own fan. The safety distance between the bottom of cooktop and the oven must be at least 2 inches. The installation must comply with all space requirements and regulations.
Electrical Connections The cooktop must connect to a separate, grounded wire, single phase, AC only electrical supply with its own circuit breaker. These appliances must be installed in accordance with National Electrical Codes, as well as all state, municipal and local codes. This appliance must be supplied with the proper voltage and frequency and amperage, which is protected by a properly sized circuit breaker or time delay fuse.
Cooktop Features Hybrid Induction-Ceramic 10 Keep Warm POWER Pause II 1. Glass Surface 2. Left Rear Burner (Induction) 3. Left Front Burner (Induction) 4. Right Rear Burner (Ceramic) 5. Right Front Burner (Ceramic) Main Control Panel 6. Left Rear Burner Display 7. Left Front Burner Display 8. Right Rear Burner Display 9. Right Front Burner Display 10. QR Code 6 3 Keep Warm POWER Pause 8 II 7 5 4 2 1 5. Power Levels 6. Burner On and Display 7. Timer 8. Pause 1. Power 2. Child Lock 3.
Compatible Cookware Ceramic Burner - Use any cookware for electric cooking. Induction Burner - Use only induction cookware or induction compatible cookware. NOTE: Follow all cookware manufacturers' recommendations when using any type of cookware on the cooktop.
Operating the Cooktop Ensure the cooktop is plugged into an electrical outlet. Place suitable cookware onto the cooktop. Main Power Press the Power icon for three seconds. This powers on the whole cooktop. You will hear a beep and see flashing lines - on the display next to all the burners. Burners To select the burner to use and the power level, press the burner icon for the desired burner. You can change the power levels by sliding your finger across the slider or by pressing a number.
Child Lock To ensure the safety of children, the cooktop controls can be locked so children cannot change the settings. To lock: hold the Child Lock icon for 3 seconds until “L0” displays and the rest of the icons are disabled except the On/Off Power icon. To unlock: hold down the Child Lock icon for 3 seconds and the cooktop will return to normal. Keep Warm Press the Keep Warm icon to allow the burner to be on at a low temperature and to keep the food warm. The display will show .
Maintenance Wait for the cooktop to cool down completely before cleaning it. Do not use chemicals and abrasive materials to clean the cooktop. Never wash the cooktop with water. Use mild detergent and a damp cloth to wipe down the cooktop. Periodically, use a vacuum cleaner to remove dust from intake and exhaust vents. burner is still hot. Troubleshooting In most cases, when your Cooktop fails to work, the problems arising can be easily solved without having to call for a technician.
Error Codes Information codes may be displayed to help you understand better what is wrong with the appliance. Error Codes Possible Cause Solution E0 No pan or incorrect pan on burner. Place correct pan on burner and ensure that if it is an induction burner there is liquid or some substance in the pan. E2 NTC short or not connected. Call for Customer Service. E3 High voltage: Higher than 260-275V. Ensure voltage is below this range. E4 Low voltage: Lower than 145-160V.
Equator Advanced Appliances USA, founded in 1991, offers Efcient, High-Quality, and Innovative household appliances. Our Mission is to simplify domestic chores and save Time, Space, and Energy.
