Service manual

ManualsBrandsEquator ManualsCRT TVsED620

SERVICE MANUAL

BA-5 CHASSIS

MODEL COMMANDER DEST CHASSIS NO.

KV-27FS12 RM-Y168 US SCC-S40D-A

KV-27FS12 RM-Y168 CND SCC-S41D-A

KV-27FS16 RM-Y169 US SCC-S40E-A

KV-29FS12 RM-Y168 E SCC-S38K-A

KV-29FS12C RM-Y168 E SCC-S38L-A

TRINITRON

COLOR TV

RM-Y168

KV-27FS16

Summary of content (64 pages)

PAGE 1
BA-5 CHASSIS SERVICE MANUAL MODEL KV-27FS12 KV-27FS12 KV-27FS16 KV-29FS12 KV-29FS12C COMMANDER DEST CHASSIS NO.
PAGE 2
KV-27FS12/27FS16/29FS12/29FS12C SPECIFICATIONS KV-27FS12 120V, 60Hz Power requirements KV-27FS16 120V, 60Hz KV-29FS12 120V/220V, 60Hz/50Hz KV-29FS12C 120V/220V, 60Hz/50Hz Number of inputs/outputs Video 1) 3 3 3 3 S Video 2) 1 1 1 1 Audio 3) 3 3 3 3 Audio Out 4) 1 1 1 1 1 1 1 1 5Wx2 5Wx2 10Wx2 10Wx2 160W 170W 185W 185W 1W 1W 1W 1W Y, PB, PR 5) Speaker output(W) Power Consumption(W) In use(Max) In standby Dimensions(W/H/D) (mm) (in) 700 x 632 x 512 mm.
PAGE 3
KV-27FS12/27FS16/29FS12/29FS12C TABLE OF CONTENTS Section Title Page Warnings and Cautions ....................................................................................................................................... 4 Self-Diagnostic Function ...................................................................................................................................... 4 Safety Check-Out Instructions ........................................................................................
PAGE 4
KV-27FS12/27FS16/29FS12/29FS12C WARNINGS AND CAUTIONS CAUTION ATTENTION!! SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR CARBON PAINTED ON THE CRT, AFTER REMOVING THE ANODE. APRES AVOIR DECONNECTE LE CAP DE L'ANODE, COURT-CIRCUITER L'ANODE DU TUBE CATHODIQUE ET CELUI DE L'ANODE DU CAP AU CHASSIS METALLIQUE DE L'APPAREIL, OU AU COUCHE DE CARBONE PEINTE SUR LE TUBE CATHODIQUE OU AU BLINDAGE DU TUBE CATHODIQUE.
PAGE 5
KV-27FS12/27FS16/29FS12/29FS12C Display of Standby/Timer LED Flash Count 2 times 4 times 5 times LED ON 0.3 sec. LED OFF 0.3 sec. STANDBY/TIMER LED LED OFF 3 sec. Diagnostic Item Flash Count* +B overcurrent I-Prot IK 2 times 4 times 5 times *One flash count is not used for self-diagnostic. Stopping the Standby/Timer LED Flash Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER LAMP from flashing.
PAGE 6
KV-27FS12/27FS16/29FS12/29FS12C Handling of Self-Diagnostic Screen Display Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. When you have completed the repairs, clear the result display to “0”. Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after completion of the repairs.
PAGE 7
KV-27FS12/27FS16/29FS12/29FS12C SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: Leakage Test The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods. 1.
PAGE 8
The instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers shown reflect those of the Operating Instruction Manual. GENERAL Operating Instructions Cable Box Connections Connecting Your TV Some pay cable TV systems to use scrambled or encoded signals that require a cable box to view all channels. Read this chapter before setting up your TV for the first time.
PAGE 9
Connecting Your TV Connecting Additional Equipment Operating Instructions TV and Cable Box TV and VCR Cable Box Rear of TV 1 Rear of TV From cable 2 VCR 2 1 From cable/ antenna 1 Connect the coaxial cable from your cable service to the IN jack on your cable box. 2 Connect a coaxial cable (not supplied) from the OUT jack on your cable box to the VHF/UHF jack on the TV. 3 (Optional connection) —9— 1 Connect the coaxial cable from your TV antenna or cable service to the IN jack on your VCR.
PAGE 10
TV, Cable box, and Cable Operating Instructions TV, VCR, and Cable box KV-27FS16, KV-27FV16, KV-32FS16, KV-29FV16 only Rear of TV For this set up, you can switch between scrambled channels (through your cable box) and normal (CATV) channels by pressing . Rear of TV (KV-27FV16 only) 3 VCR Cable Box 2 Cable box From Cable 1 4 (Optional connection) — 10 — Cable When using PIP, the AUX input cannot be viewed in the window picture.
PAGE 11
Connecting Your TV TV and Satellite Receiver Operating Instructions TV, Satellite Receiver, and VCR Satellite antenna cable Rear of TV 2 1 From cable/ antenna Rear of TV 4 VCR SATELLITE IN 1 VHF/UHF AUDIO R AUDIO L VIDEO Satellite receiver 2 AUDIO R AUDIO L VIDEO IN OUT LINE OUT VHF/UHF LINE IN IN SATELLITE IN VHF/UHF AUDIO R AUDIO L VIDEO Satellite antenna cable From cable/ antenna Satellite receiver IN OUT LINE OUT OUT 3 LINE OUT 5 3 — 11 — 1 Connect the cable from your
PAGE 12
Using the Remote Control and Basic Functions SLEEP Turns the TV off automatically in approximately 15, 30, 45, 60, 90, or 120 minutes. Cancel by pressing until SLEEP OFF appears. MTS/SAP Cycles through the Multi-channel TV Sound (MTS) options: Stereo, Mono, and Auto-SAP (Second Audio Programming). DISPLAY Press once to show current time, (if set) and channel number. This section shows you how to use the more advanced buttons on the remote control and how to use the on-screen menus.
PAGE 13
Other Information Troubleshooting If you are having a problem with your TV, try the suggestions below. If the problem persists, contact your nearest Sony dealer. — 13 — Poor or no picture, good sound Good picture, no sound No color No signal Double images or ghosts Cable stations don’t seem to work Remote control does not operate The TV needs to be cleaned Adjust Picture in the Video menu (page 22). Adjust Brightness in the Video menu (page 22).
PAGE 14
KV-27FS12/27FS16/29FS12/29FS12C SECTION 2 DISASSEMBLY 2-1. REAR COVER REMOVAL Screw +BVTP 4x16 Rear Cover Screw +BVTP 4x16 Screw +BVTP 4x16 Screw +BVTP 4x16 Screw +BVTP 4x16 Screw +BVTP 4x16 Screw +BVTP 4x16 2-2. CHASSIS ASSEMBLY REMOVAL 2-3.
PAGE 15
KV-27FS12/27FS16/29FS12/29FS12C 2-4. PICTURE TUBE REMOVAL 1 WARNING: BEFORE REMOVING THE ANODE CAP 10 9 High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to remove the anode cap. Short between anode and CRT coated earth ground strap. 2 8 7 3 6 5 4 Coated Earth Ground Strap 1. Discharge the anode of the CRT and remove the anode cap. 6. Loosen the deflection yoke fixing screw and remove. 2.
PAGE 16
KV-27FS12/27FS16/29FS12/29FS12C SECTION 3 SET-UP ADJUSTMENTS The following adjustments should be made when a complete realignment is required or when a new picture tube is installed. Perform the adjustments in order as follows: 1. Beam Landing 2. Convergence 3. Focus 4. Screen (G2) 5. White Balance These adjustments should be performed with rated power supply voltage unless otherwise noted.
PAGE 17
KV-27FS12/27FS16/29FS12/29FS12C 3-2. CONVERGENCE Horizontal Static Convergence Before starting convergence adjustments: If the blue dot does not converge with the red and green dots, perform the following: 1. Perform FOCUS, V.LIN AND V.SIZE adjustments. 1. Move BMC magnet (a) to correct insufficient H. Static convergence. 2. Set BRIGHTNESS control to minimum. 3. Feed in dot pattern. 2. Rotate BMC magnet (b) to correct insufficient V. Static convergence. Vertical Static Convergence 3.
PAGE 18
KV-27FS12/27FS16/29FS12/29FS12C 4. Adjust XCV core to balance X axis. 5. Adjust YCH VR to balance Y axis. R B G R B G G B RG B R R G B B G R 6. Adjust vertical red and blue convergence with V.TILT (TLV VR). Note: Perform adjustments while tracking items 1 and 2. B G R R G B Screen-Corner Convergence 1. Affix a permalloy assembly corresponding to the misconverged areas. B R G B R G G R B GR B a b a 4. Tighten the deflection yoke screw. a-d: screen-corner 5. Install the deflection yoke spacers.
PAGE 19
KV-27FS12/27FS16/29FS12/29FS12C 3-4. SCREEN (G2) 3-6. WHITE BALANCE ADJUSTMENTS 1. Input a dots pattern. 1. Input an entire white signal with burst. 2. Set the PICTURE and BRIGHTNESS controls at minimum and COLOR control at normal. 2. Set to Service Adjustment Mode. 3. Adjust SBRT, GCUT, BCUT in service mode with an oscilloscope as shown below so that voltages on the red, green, and blue cathodes are 170 VDC. 4. Adjust with SBRT if necessary. 3. Set the PICTURE and BRIGHTNESS to minimum. 5.
PAGE 20
KV-27FS12/27FS16/29FS12/29FS12C SECTION 4 SAFETY RELATED ADJUSTMENTS 4-1. R564 CONFIRMATION METHOD (HV HOLD-DOWN CONFIRMATION) AND READJUSTMENTS Hold-Down Readjustment If the setting indicated in step 2 of Hold-Down Operation Confirmation cannot be met, readjustment should be performed by altering the resistance value of R564 component marked with . The following adjustments should always be performed when replacing the following components which are marked with on the schematic diagram: ammeter 3.
PAGE 21
KV-27FS12/27FS16/29FS12/29FS12C POWER SUPPLY DIGITAL MULTIMETER + – + – 1SS119 R564 C546 1 9 R454 R438 R449 JR503 C448 + R450 C530 R529 R567 R565 R445 IC501 R522 Q411 R525 8 Q503 D620 18 10 R225 R403 5 D235 R563 C546 R573 R531 R447 4 H.PROT D234 C213 R218 R407 C542 Q205 Q206 E B E R659 C659 6 4 D232 6 2 R539 D506 2 R506 C510 R518 7 T504 L509 R231 D233 D520 R511 C525 C550 D518 R540 C543 C511 L505 H.
PAGE 22
KV-27FS12/27FS16/29FS12/29FS12C SECTION 5 CIRCUIT ADJUSTMENTS ELECTRICAL ADJUSTMENTS BY REMOTE COMMANDER Use the Remote Commander (RM-Y168 or RM-Y169) to perform the circuit adjustments in this section. NOTE: Test Equipment Required: • • • • Pattern generator Frequency counter Digital multimeter Audio oscillator 5-1. SETTING THE SERVICE ADJUSTMENT MODE 5-2. MEMORY WRITE CONFIRMATION METHOD 1. Standby mode (power off). 1. After adjustment, remove the power plug from the AC outlet, then plug it in again.
PAGE 23
KV-27FS12/27FS16/29FS12/29FS12C Adjustment Items Reg # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 ITEM HSIZ HPOS VBOW VANG VTRP HTRP TROT PAMP UPIN LPIN VSIZ VPOS VLIN SCOR VZOM EHT ASP SCRL HBLK LBLK RBLK HDW EWDC LVLN UVLN INTL G2SW G2LV HOSC VSS HSS HMSK VTMS CDMD AFC FIFR VBLK REFP JPSW RDRV GDRV BDRV RCUT GCUT BCUT SCON
PAGE 24
KV-27FS12/27FS16/29FS12/29FS12C Reg # 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 ITEM PDSO CK VNL HPK HPKO CORE TRAP CHTR CBPF ENHO NMRD YAPS CLKS NSTD MSS KILS ADIN EXCS CPP HDP CDL DYCR DYGN DCCR DCGN YNRL CNRL WSC VTRH VTRR LDSR VAPG VAPI TEST YPFT YPFG
PAGE 25
KV-27FS12/27FS16/29FS12/29FS12C Reg # 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 ITEM PDCO PCGA PAAF PSU2 PCVF PBIT PAFC PACC PBUR PEVE PINW PINR PREF PARE PAVE PFRA PPAL PHPO PVPO PHTI PHAJ PBGY PCRO PPAR PHPF PFSC PVCH PVON PVLN PVSB PVLV SBAL SBAS STRE BBEL BBEH BBE AUX DISP HCLW HCHG ID0 ID1 ID2 ID3 ID4 ID5 ID6 FUNCTION C_GAIN BITSEL AFCBITSEL ACC_LEVEL
PAGE 26
KV-27FS12/27FS16/29FS12/29FS12C 3. Activate the Service Adjustment Mode.4. Set both GON and and ; set each to the following BON items. Using values. Leave RON set to “1”. Sub Hue, Sub Color Adjustment (CHUE, CCOL) 1. Input a color-bar signal. 2. Activate the Service Adjustment Mode. SERVICE RON 3. Connect an oscilloscope probe to CA Board, CN1752 Pin . 1 1: ON 0: OFF R ON: G ON: B ON: 4. Select the CHUE and CCOL item with ON (1) OFF (0) OFF (0) . 6.
PAGE 27
KV-27FS12/27FS16/29FS12/29FS12C horizontal center. then 5. Press to save into the memory. V ANGLE (VANG) V BOW (VBOW) H. Size Adjustment (HSIZ) 1. Input a monoscope signal. 2. Activate the Service Adjustment Mode. 3. Select HSIZ with 4. Adjust with 5. Press and and UPPER PIN (UPIN) . for the best horizontal size. then to save into the memory. LOW PIN (LPIN) V. Linearity (VLIN), V. Correction (VSCO), Pin Amp (PAMP), and Horizontal Trapezoid (TRAP) Adjustments Service Adjustment Mode Memory 1.
PAGE 28
KV-27FS12/27FS16/29FS12/29FS12C NOTES: — 28 —
PAGE 29
KV-27FS12/27FS16/29FS12/29FS12C NOTES: — 29 —
PAGE 30
KV-27FS12/27FS16/29FS12/29FS12C NOTES: — 30 —
PAGE 31
KV-27FS12/27FS16/29FS12/29FS12C SECTION 6 DIAGRAMS 6.
PAGE 32
KV-27FS12/27FS16/29FS12/29FS12C TU150 MEMORY 9V 9V 30V 30V 5V 5V DIG COMB IC003 FILTER IC1302 2ND TUNER Y/C/J COUT YOUT AFT OUT SDA SCL AIN CLOCK CKIN DATA DE-EM OUT MUTE CN302 DET-OUT 1 2 KV-27FS16 ONLY Y-TO-YUV CR 3 CB 4 GND A BUFFER Q3300,3308 CN1002 BUFFER FOR JIG Q001 B-CLK 1 B-DAT 2 B-INT 3 GND 4 STBY+5V REG STBY+7.5V IC002 CN305 RESET IO-BCLKN BUFFER IO-BDAT 9 VM 8 STBY 7.
PAGE 33
KV-27FS12/27FS16/29FS12/29FS12C A BOARD IC BLOCK DIAGRAMS 6.2 CIRCUIT BOARD LOCATIONS A BOARD: IC401 TDA7057AQ/N2 (KV-27FS12/27FS16 ONLY) V HX Board P 4 I+i 3 CA Board 13 Input 1 1 DC Volume Control 1 + Positive Output 1 A BOARD: IC502 TDA8172 1 – VA Board Claw D Board A Board MA Board P Board K Board 6-3. PRINTED WIRING BOARDS SCHEMATIC DIAGRAMS AND • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytic and tantalums.
PAGE 34
KV-27FS12/27FS16/29FS12/29FS12C [POWER SUPPLY, DEFLECTION, TUNER/IF, AUDIO, MTS] R423 CN2007 25 SDAT D205 D208 R115 21 23 R105 Q101 R442 E 9 1 11 1 11 B C614 3 GND 27 17 D603 13 15 6 R102 7 L103 SCL 2 1 L101 AGC R114 Y2 GND D212 CN2005 R106 R508 D604 R618 KEY STBY-5V V2 GND C216 D206 CN2006 R204 CN2002 CN603 5V SET Q410 C661 C2 L102 R623 D210 R211 C102 R215 9V SET JR604 4 B 5 2 GND Q603 L601 RBK C403 R644 C652 IC604 IC602 D611 R424 1 I O R
PAGE 35
KV-27FS12/27FS16/29FS12/29FS12C A BOARD MARK (*) LIST A BOARD TRANSISTOR VOLTAGE LIST A BOARD SCHEMATIC DIAGRAM Q101 PIP-L C204 0.0047 B:CHIP 10 C216 4.7 R237 220 CHIP C210 4.7 R235 470k CHIP R238 220 CHIP D212 MTZJ-T-77-10B SET-5V TP101 R204 22k :CHIP SET 9V C641 10 450V J202 FRONT A/V Q605 2SK2663 CONVERTER R608 22M 1/2W 1 9V D624 1SS133T-77 3 1 L R617 22 R R610 10k CHIP D618 1SS133T-77 R616 6.8 1/2W C637 0.
PAGE 36
KV-27FS12/27FS16/29FS12/29FS12C MA BOARD SCHEMATIC DIAGRAM GND VM SPSW 8 9 I-PROT STBY 7.
PAGE 37
KV-27FS12/27FS16/29FS12/29FS12C MA BOARD IC VOLTAGE LIST [TUNING CONTROL, 2ND TUNER, Y/C/J] IC001 volt 18 0.1 37 3.1 56 1.0 19 4.3 38 5.0 57 NC pin 0.5 20 0.1 39 NC 58 0.1 1 2 4.8 21 NC 40 NC 59 NC 3 NC 22 5.0 41 NC 60 NC 4 5.0 23 NC 42 4.8 61 5 0.0 24 5.0 43 4.8 62 6 0.0 25 2.1 44 NC 63 0.1 7 2.4 26 NC 45 4.8 64 0.1 IC002 volt 8 5.0 17 4.4 36 3.9 55 1.6 8 5.0 5 4.8 pin IC301 pin volt 18 GND 37 1.9 56 1.7 9 4.8 6 5.
PAGE 38
KV-27FS12/27FS16/29FS12/29FS12C CA BOARD SCHEMATIC DIAGRAM [RGB DRIVE, CRT DRIVE] 1 R717 2.2 2W 2 3 1 2 3 KG KB G2 A IC701 4 5 5 6 CV 1 8 13 9 12 10 11 KR VDD R OUT B OUT G OUT 2.
PAGE 39
KV-27FS12/27FS16/29FS12/29FS12C [CONVERGENCE] NC 2 GND 3 GND 4 9V 5 H.P 6 VD+ R866 10k :CHIP 4 3 2 R863 2.2k :CHIP 1 Q811 2SA1309A QP DRIVE 5 6 7 R825 100k C808 0.01 :CHIP R860 10k :RN-CP C821 0.01 :CHIP +B CN802 1P R853 JW(5.0MM) :RS TO A BOARD 4 CN504 R839 100 :CHIP C818 0.0015 500V 2 1 C820 0.47 160V 6 1 C817 0.0039 630V R847 100k R846 100k R845 100k C815 0.022 630V :PP D812 ERB44-06 CLAMP D811 ERA38-06 DAMP 4 IC802 NJM2903D DF-COMP R849 3.
PAGE 40
KV-27FS12/27FS16/29FS12/29FS12C K BOARD SCHEMATIC DIAGRAM [VELOCITY MODULATOR] 2 3 1 2 1 JW419 C425 JR408 JR402 JW405 5MM JW403 7.5MM AUDIO-R R409 100 R404 100 1 S.R.S IC403 C431 C430 C446 12 C415 R876 R911 1 CN901 B Q903 E C912 R913 R916 5 R923 R919 B R220 4.7k Q906 B R219 CN450 DATA R920 R410 100 C C422 C450 20 JR451 E C407 0.22 :CHIP JR428 C418 C903 R219 4.7k R405 100 C406 0.0015 B:CHIP C409 R409 R901 C412 0.1 :CHIP AUDIO-L C AUDIO-R E C413 4.
PAGE 41
KV-27FS12/27FS16/29FS12/29FS12C [PIP, CHROMA DECODER] COMPONENT SIDE 2 1 X3300 :CHIP C3344 0.22 25V :CHIP R3404 22k :CHIP R3300 R3384 R3386 470 680 :CHIP C3320 0.47 470 :CHIP F:CHIP R3387 1k :CHIP Q3321 2SB709A BUFFER R3322 56k :CHIP C3331 0.001 :CHIP C3340 220 :CHIP 47 IC3300 NJM2534M(TE2) VIDEO SW :CHIP NOTCH VCC PAL/NTSC R3396 22k :CHIP CVBS FLT GREEN VSS BLUE CHROMA VOFF VREF L3300 C3352 0.22 25V F:CHIP Q3323 2SD601A BUFFER C3354 0.022 IC3300 7 2 3 6 4 5 0.
PAGE 42
KV-27FS12/27FS16/29FS12/29FS12C SECTION 7 EXPLODED VIEW 6-4. SEMICONDUCTORS 2SA1037AK-7146-QR 2SB709A-QRS-TX 2SD601A-QRS-TX 2SC2412K-T-146-QR 2SB734-7-34 2SC3209LK-TP 2SC1740S-QRT 2SA1309A-QRSTA 2SC3311A-QRSTA 2SD2144S-TP-UVW 2SC3840K Items with no part number and no description are not stocked because they are seldom required for routine service. The component parts of an assembly are indicated by the reference numbers in the remarks column.
PAGE 43
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: Les composants identifies per un trame et une marque sont critiques pour la securite. Ne les remplacer que par une piece portant le numero specifie. The components identified by shading and mark are critical for safety. Replace only with part number specified. 7-2.
PAGE 44
KV-27FS12/27FS16/29FS12/29FS12C SECTION 8 ELECTRICAL PARTS LIST Note: The components identified by in this manual have been carefully factory-selected for each set in order to satisfy regulations regarding X-ray radiation. Should replacement be required, replace only with the value originally used. The components identified by shading and mark are critical for safety. Replace only with part number specified. • Note: Les composants identifies per un trame et une marque sont critiques pour la securite.
PAGE 45
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading are critical for safety. Replace and mark only with part number specified. Les composants identifies per un trame et une marque sont critiques pour la securite. Ne les remplacer que par une piece portant le numero specifie. REF.NO. PART NO. DESCRIPTION REF.NO. PART NO. DESCRIPTION C547 C548 C549 C550 C551 1-163-031-11 1-104-710-11 1-126-934-11 1-107-846-11 1-137-417-11 CERAMIC CHIP ELECT ELECT FILM MYLAR 0.
PAGE 46
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION DIODE D204 D208 D209 D210 D211 8-719-982-22 8-719-110-17 8-719-977-22 8-719-110-17 8-719-108-12 DIODE MTZJ-T-77-30D DIODE MTZJ-T-77-10B DIODE UDZ-TE-17-9.1B DIODE MTZJ-T-77-10B DIODE RD9.
PAGE 47
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO.
PAGE 48
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO.
PAGE 49
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO.
PAGE 50
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO.
PAGE 51
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading and mark are critical for safety. Replace only with part number specified. Les composants identifies per un trame et une marque sont critiques pour la securite. Ne les remplacer que par une piece portant le numero specifie. REF.NO. PART NO.
PAGE 52
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK R812 R813 R815 R816 R817 1-216-061-00 1-216-041-00 1-215-862-11 1-247-807-31 1-216-091-00 RES-CHIP RES-CHIP METAL OXIDE CARBON RES-CHIP 3.
PAGE 53
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading and mark are critical for safety. Replace only with part number specified. Les composants identifies per un trame et une marque sont critiques pour la securite. Ne les remplacer que par une piece portant le numero specifie. REF.NO. PART NO. DESCRIPTION REMARK C412 C413 C414 C415 C416 1-163-038-91 1-126-963-11 1-126-963-11 1-126-963-11 1-126-963-11 CERAMIC CHIP ELECT ELECT ELECT ELECT 0.1µF 4.7µF 4.7µF 4.7µF 4.
PAGE 54
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION C034 C037 C038 C039 C040 1-163-037-11 1-164-161-11 1-126-935-11 1-126-964-11 1-163-229-11 CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP 0.022µF 0.
PAGE 55
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading and mark are critical for safety. Replace only with part number specified. Les composants identifies per un trame et une marque sont critiques pour la securite. Ne les remplacer que par une piece portant le numero specifie. REF.NO. PART NO. DESCRIPTION C369 C370 C371 C377 C389 1-163-021-91 1-126-933-11 1-163-243-11 1-126-963-11 1-115-185-11 CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP 0.01µF 100µF 47PF 4.7µF 0.
PAGE 56
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK L301 L302 L303 L304 L305 1-414-267-11 1-414-271-11 1-414-856-11 1-414-856-11 1-414-267-11 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 10µH 47µH 10µH 10µH 10µH L308 L310 L350 L351 1-414-273-11 1-414-273-11 1-414-856-11 1-414-856-11 INDUCTOR INDUCTOR INDUCTOR INDUCTOR 100µH 100µH 10µH 10µH TRANSISTOR REF.
PAGE 57
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. R046 R047 R048 220 4.
PAGE 58
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO.
PAGE 59
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading and mark are critical for safety. Replace only with part number specified. Les composants identifies per un trame et une marque sont critiques pour la securite. Ne les remplacer que par une piece portant le numero specifie. REF.NO. PART NO.
PAGE 60
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK R3311 R3312 R3313 R3316 R3317 1-216-037-00 1-216-043-91 1-216-035-00 1-216-295-91 1-216-295-91 RES-CHIP RES-CHIP RES-CHIP SHORT SHORT 330 560 270 5% 5% 5% R3318 R3319 R3320 R3321 R3322 1-216-061-00 1-216-295-91 1-216-073-00 1-216-049-91 1-216-091-00 RES-CHIP SHORT RES-CHIP RES-CHIP RES-CHIP 3.
PAGE 61
KV-27FS12/27FS16/29FS12/29FS12C Note: Note: The components identified by shading and mark are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION C908 C909 C910 C911 C912 C913 C914 1-126-925-11 1-161-830-00 1-104-999-11 1-104-665-11 1-126-941-11 1-102-074-00 1-130-491-00 ELECT CERAMIC MYLAR ELECT ELECT CERAMIC MYLAR Les composants identifies per un trame et une marque sont critiques pour la securite.
PAGE 62
KV-27FS12/27FS16/29FS12/29FS12C NOTES: — 78 —
PAGE 63
KV-27FS12/27FS16/29FS12/29FS12C NOTES: — 79 —
PAGE 64
KV-27FS12/27FS16/29FS12/29FS12C 9-965-882-01 Sony Corporation English Sony Technology Center Product Quality Division Service Promotion Dept. 2000DS74325-1 Printed in USA 2000.