Installation guide

QuadroM32x/8L/26x/12Li/26xi Manual II: Administrator's Guide Administrator’s Menus
QuadroM32x/8L/26x/12Li/26xi; (SW Version 5.3.x)
117
If the Send ALERT Message on Call Ringing checkbox is selected, the system will send ALERT messages to callers from the PSTN/PBX on call
ringing. If not, the system will send a PROGRESS message on receiving early media from the called party if the Generate Progress Tone to
PSTN/PBX setting is not set to None.
Enable CLIR Service checkbox selection enables Calling Line Identification Restriction (CLIR) service which displays the incoming caller ID only in
case if Presentation Indication is allowed on the remote side. Otherwise, if CLIR service is disabled, caller ID will be unconditionally displayed.
When the Enable Connect Acknowledge Option checkbox is selected, Quadro will stop the T303 and T310 timers upon receiving the CONNECT
message, will send a CONNECT ACKNOWLEDGE message to the remote side and enter the active state. When this checkbox is not selected,
Quadro will stop the T303 and T310 timers upon receiving the CONNECT message and will enter the active state without sending the CONNECT
ACKNOWLEDGE message to the remote side.
P-Asserted-Identity:
The Disable P-Asserted-Identity radio button disables the P-Asserted-Identity feature for both incoming and outgoing calls.
The Override CLID with P-Asserted-Identity radio button selection enables the SIP P-Asserted-Identity support.
For the calls from SIP to E1/T1 if the Invite SIP message contains a P-Asserted-Identity or a P-Preferred-Identity or a Remote-Party-ID, then the
CallerID on E1/T1 is sent with the original Caller ID which comes from the identity field. SIP user agent should check for the existence of the P-
Asserted-Identity, then the P-Preferred-Identity, then the Remote-Party-ID to fill the identity field.
For the calls from E1/T1 to SIP with restricted Caller ID, the SIP Invite message contains P-Asserted-Identity field with the value from the Caller ID
on E1/T1. The SIP From field contains anonymous.
The Use Redirecting Number Info Element with P-Asserted-Identity radio button selection enables full support of the SIP P-Asserted-Identity.
For the calls from SIP to E1/T1, if the SIP Invite message contains a P-Asserted-Identity or a P-Preferred-Identity or a Remote-Party-ID, then the
CallerID on E1/T1 contains the number from the user name field and the Redirecting Number IE contains the original number from the identity field.
SIP user agent should check for the existence of the P-Asserted-Identity, then the P-Preferred-Identity, then the Remote-Party-ID to fill the identity
field.
For the calls from E1/T1 to SIP with Caller ID, the SIP Invite message contains P-Asserted-Identity field with the original number value from the
Redirecting Number IE on E1/T1. The SIP From field contains the value from the user name.
The E1/T1 Trunk Status page provides information about the selected trunk state. Following information is displayed on this page:
• E1/T1 mode - displays which mode is selected: E1 or T1.
• Interface Type - displays selected interface type: User or Network.
• Signaling Type - displays selected signaling type: CAS or CCS.
• Clock Mode - displays the selected clock mode: Master or Slave.
• Framing mode - displays selected framing mode.
• Link - displays E1/T1 link state: up or down.
• Frame Synchronization - displays the signal synchronization state in the trunk: Yes or No.
• Red Alarm - indicates that the receive frame alignment for the line has been lost and the data cannot be properly extracted. The red alarm is
indicated by the loss of frame condition for the various framing formats.
• Out of Frame - number of Out of Frame errors.
• Line Code Violation - number of Line Code Violation errors.
• Frame Synchronization - number of Frame Synchronization errors.
• Link Synchronization - number of Link Synchronization errors.
The following statistics are available, if CAS Signaling is selected:
• Active Calls - currently active calls in the selected trunk.
• Outgoing Calls - total outgoing calls in the selected trunk.
• Incoming Calls - total incoming calls in the selected trunk.
Following statistics is available when CCS Signaling is selected:
ISDN PRI Layer statistics:
• Received Packets - number of received packets.
• Received Errors - number of received errorneous packets.
• Transmitted Packets - number of transmitted packets.
• Transmitted Errors - number of transmitted errorneous packets.
ISDN PRI Layer 2 statistics is displayed for actual TEI value and the received and transmitted packets:
• TEI Value – the actual TEI assigned.
• L2 State – the state of the TEI assignment.
• Information Frame - signaling packets for call initiation and termination.
• Receive Ready - controlling packets during E1/T1 link is up.